Intelliflo VF Installation / Owners Manual - Pool Center

More documents

Recommendations

Info

26 Features 1 – 2 (Flow and Duration) To run Feature 1 or 2 (Flow and Duration) 1. Press the Feature 1 or Feature 2 button, then press the Start/Stop button. The active feature LED will be on until the process is finished. 2. The Features screen will then start to subtract time in minutes from your duration or you can scroll using the Up or Down arrow buttons to see the power, speed, or flow status. The following screen shown Feature 1 initiated: IntelliFlo ® IntelliFlo ® IntelliFlo ® Feature 1 12:54 50.GPM Set Flow Feature 1 3:02 0:01 Time Duration FEATURE 1 5:01 1.MIN REMAINING TIME RUNNING Time remaining in minutes Pump run status Filter Vacuum Back Wash Manual Filter Vacuum Back Wash Manual Filter Vacuum Back Wash Manual Select Escape Select Escape Select Escape On Enter Menu On Enter Menu On Enter Menu Warn. Warn. Warn. Alarm Alarm Alarm Feature 1 Feature 2 Start Stop Reset Feature 1 Feature 2 Start Stop Reset Feature 1 Feature 2 Start Stop Reset Start / Stop LED on Feature 1 LED on Features 3 – 9 (Flow, Start/Stop Time) Feature 3 – 9 affect the “Filter” mode as shown on page 20. Feature 3 – 9 are programmed by a flow rate and a start/stop time and are automatically initiated. They are controlled by the time of day. All alerts and alarms are active in Feature mode. Feature 3 – 9 must be enabled in its menu. Enabling Features 3 – 9 To use any Feature 3 – 9 it must be first enabled. If it is not enabled, it will not work with the parameters in the “Set Flow” and “Set Start Time” and “Set Stop Time” settings. Features 3 – 9 are each programmed in the same way. Three parameters are required after Enabling; Flow, Start, and Stop. To use the Feature 3 settings; Enabled, Set Flow, Set Start Time, and Set Stop Time: 1. Ensure that the green power LED is on and the pump is stopped. 2. Press the Menu button. Press the Up or Down arrows to select the “Features” menu. Press the Down arrow button to select Feature 3. Press the Select button to access the Feature 3 menu settings. The Features 3 menu setting is displayed. IntelliFlo VF Installation and User’s Guide
27 3. To enable Feature 3: Press the Select button then the Down arrow button to select Enabled if not already selected. Press the Enter button to save the setting. 4. To set the flow rate for Feature 3: Press the Down arrow button to select “Set Flow” setting. Press the Select button to access the setting. To edit the flow rate (GPM) setting, see step 6. 5. To set the start and stop time for Feature 3: Press the Down arrow button to select “Start Time” or Stop Time” setting. Press the Select button to access the setting. To edit the start and stop time, see step 6. 6. Press the Select button to change the current value. 7. To change the value, press the Left and Right arrows to select which digit to modify, then use the Up and Down arrows to change the selected digit. 8. When you are done, press the Enter button to save the changes. To cancel any changes, press the Escape button to exit edit mode without saving. IntelliFlo ® Features 5:22 Feature 3 IntelliFlo ® Feature 3 4:50 Disabled Activation IntelliFlo ® Feature 3 5:18 Enabled Activation Filter On Warn. Select Back Vacuum Wash Enter Escape Manual Menu Filter On Warn. Select Back Vacuum Wash Enter Escape Manual Menu Select + + Enter Filter On Warn. Select Back Vacuum Wash Enter Escape Manual Menu Alarm Alarm Alarm Feature 1 Feature 2 Start Stop Reset Feature 1 Feature 2 Start Stop Reset Feature 1 Feature 2 Start Stop Reset Filter Cycle Examples Flow Flow Feature 3 50 gpm 20 gpm 20 gpm Filter Cycle Filter Cycle Time Time 8:00 am 10:00 PM 8:00 am 6:00 pm 6:10 pm 9:45 pm Original Filter Cycle w/No Timed Feature New Flow/Time Optimized Filter Cycle Note: Refer to page 20 for further explaination. IntelliFlo VF Installation and User’s Guide
Page 1 and 2: IntelliFlo ® VF Variable Flow Pump
Page 3 and 4: i Contents Important Safety Precaut
Page 5 and 6: F iii IMPORTANT SAFETY PRECAUTIONS
Page 7 and 8: v IMPORTANT SAFETY PRECAUTIONS (con
Page 9 and 10: IntelliFlo ® VF Overview 1 Section
Page 11 and 12: 3 Operator control panel cover Driv
Page 13 and 14: This section describes the operator
Page 15 and 16: 7 Navigating the Menu Structure Bef
Page 17 and 18: This section describes how to use t
Page 19 and 20: 11 Manual Mode (Continued) 9. Press
Page 21 and 22: 13 Pool Data Mode Use the Pool Data
Page 23 and 24: 15 Priming Mode (Continued) 6. To s
Page 25 and 26: 17 Filter Mode (Continued) 5. To se
Page 27 and 28: 19 Filter Mode (Continued) Clean Fi
Page 29 and 30: 21 Filter Mode (Continued) Flow Con
Page 31 and 32: 23 Features Mode The Feature mode c
Page 33: 25 Features Mode (Continued) The fu
Page 37 and 38: 29 External Control with IntelliCom
Page 39 and 40: 31 Controlling IntelliFlo with the
Page 41 and 42: 33 Backwash Mode When the Filter mo
Page 43 and 44: 35 Vacuum Mode Use Vacuum mode to c
Page 45 and 46: 37 Section 4 User Maintenance The f
Page 47 and 48: 39 Winterizing The IntelliFlo’s i
Page 49 and 50: Section 5 Installation and Removal
Page 51 and 52: 43 Pump Disassembly WARNING — Alw
Page 53 and 54: 45 Drive Assembly Removal and Insta
Page 55 and 56: 12.50 47 IntelliFlo VF Pump Dimensi
Page 57 and 58: Alerts and Warnings The IntelliFlo
Page 59 and 60: 51 IntelliFlo VF Installation and U
Page 61 and 62: 53 How to make your pool more energ
Page 63 and 64: 55 Notes IntelliFlo VF Installation
Page 65 and 66: Notes

Intelliflo VF Installation / Owners Manual - Pool Center

Create successful ePaper yourself

Delete template?

Save as template?