Intelliflo VF Installation / Owners Manual - Pool Center
Intelliflo VF Installation / Owners Manual - Pool Center
Intelliflo VF Installation / Owners Manual - Pool Center
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
26<br />
Features 1 – 2 (Flow and Duration)<br />
To run Feature 1 or 2 (Flow and Duration)<br />
1. Press the Feature 1 or Feature 2 button, then press the Start/Stop button. The active feature LED<br />
will be on until the process is finished.<br />
2. The Features screen will then start to subtract time in minutes from your duration or you can scroll<br />
using the Up or Down arrow buttons to see the power, speed, or flow status.<br />
The following screen shown Feature 1 initiated:<br />
IntelliFlo ®<br />
IntelliFlo ®<br />
IntelliFlo ®<br />
Feature 1 12:54<br />
50.GPM<br />
Set Flow<br />
Feature 1 3:02<br />
0:01<br />
Time Duration<br />
FEATURE 1 5:01<br />
1.MIN<br />
REMAINING TIME<br />
RUNNING<br />
Time remaining in minutes<br />
Pump run status<br />
Filter<br />
Vacuum<br />
Back<br />
Wash<br />
<strong>Manual</strong><br />
Filter<br />
Vacuum<br />
Back<br />
Wash<br />
<strong>Manual</strong><br />
Filter<br />
Vacuum<br />
Back<br />
Wash<br />
<strong>Manual</strong><br />
Select<br />
Escape<br />
Select<br />
Escape<br />
Select<br />
Escape<br />
On<br />
Enter<br />
Menu<br />
On<br />
Enter<br />
Menu<br />
On<br />
Enter<br />
Menu<br />
Warn.<br />
Warn.<br />
Warn.<br />
Alarm<br />
Alarm<br />
Alarm<br />
Feature<br />
1<br />
Feature<br />
2<br />
Start<br />
Stop<br />
Reset<br />
Feature<br />
1<br />
Feature<br />
2<br />
Start<br />
Stop<br />
Reset<br />
Feature<br />
1<br />
Feature<br />
2<br />
Start<br />
Stop<br />
Reset<br />
Start / Stop LED on<br />
Feature 1 LED on<br />
Features 3 – 9 (Flow, Start/Stop Time)<br />
Feature 3 – 9 affect the “Filter” mode as shown on page 20.<br />
Feature 3 – 9 are programmed by a flow rate and a start/stop time and are automatically initiated. They are<br />
controlled by the time of day. All alerts and alarms are active in Feature mode. Feature 3 – 9 must be<br />
enabled in its menu.<br />
Enabling Features 3 – 9<br />
To use any Feature 3 – 9 it must be first enabled. If it is not enabled, it will not work with the parameters in<br />
the “Set Flow” and “Set Start Time” and “Set Stop Time” settings. Features 3 – 9 are each programmed in<br />
the same way. Three parameters are required after Enabling; Flow, Start, and Stop.<br />
To use the Feature 3 settings; Enabled, Set Flow, Set Start Time, and Set Stop Time:<br />
1. Ensure that the green power LED is on and the pump is stopped.<br />
2. Press the Menu button. Press the Up or Down arrows to select the “Features” menu. Press the<br />
Down arrow button to select Feature 3. Press the Select button to access the Feature 3 menu<br />
settings. The Features 3 menu setting is displayed.<br />
IntelliFlo <strong>VF</strong> <strong>Installation</strong> and User’s Guide