Intelliflo VF Installation / Owners Manual - Pool Center
Intelliflo VF Installation / Owners Manual - Pool Center
Intelliflo VF Installation / Owners Manual - Pool Center
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
18<br />
Filter Mode (Continued)<br />
Filter Cycle Settings<br />
Note: The control panel is disabled when the <strong>Intelliflo</strong> is communicating with an IntelliTouch.<br />
"DISPLAY NOT ACTIVE!" will be displayed.<br />
NAME<br />
Turnovers<br />
Day<br />
Per<br />
Cycles per<br />
Day<br />
Clean Filter<br />
Pressure<br />
Start Cycle 1<br />
Stop Cycle 1<br />
Start Cycle 2<br />
Stop Cycle 2<br />
Start Cycle 3<br />
Stop Cycle 3<br />
Start Cycle 4<br />
Stop Cycle 4<br />
VALUE<br />
1-8 (Default 1)<br />
1-4 Cycles (Default 1)<br />
1-50 PSI (Default 14<br />
PSI)<br />
1:00 -12:59 HH.MM<br />
am/pm (Default 9:00<br />
am)<br />
1:00 -12:59 HH.MM<br />
am/pm (Default 9:00<br />
pm)<br />
1:00 -12:59 HH.MM<br />
am/pm (Default 9:10<br />
pm)<br />
1:00 -12:59 HH.MM<br />
am/pm (Default 9:20<br />
pm)<br />
1:00 -12:59 HH.MM<br />
am/pm (Default 9:30<br />
pm)<br />
1:00 -12:59 HH.MM<br />
am/pm (Default 9:40<br />
pm)<br />
1:00 -12:59 HH.MM<br />
am/pm (Default 9:50<br />
pm)<br />
1:00 -12:59 HH.MM<br />
am/pm (Default 10:00<br />
pm)<br />
DESCRIPTION<br />
The number of times per day the volume of water setup<br />
in "<strong>Pool</strong> Volume" will be moved.<br />
The number of cycles (start and stop) the IntelliFlo must<br />
do per day.<br />
The differential pressure from the 0-pressure to 100%<br />
filter status.<br />
Start<br />
time for cycle 1 (if start and stop is the same time<br />
the IntelliFlo will run 24*7).<br />
Stop<br />
time for cycle 1 (if start and stop is the same time<br />
the IntelliFlo will run 24*7).<br />
S tart time for cycle 2. If "Cycles per day" is below 2,<br />
"OFF" will be shown in the display and data cannot be<br />
entered.<br />
S top time for cycle 2. If "Cycles per day" is below 2,<br />
"OFF" will be shown in the display and data cannot be<br />
entered.<br />
S tart time for cycle 3. If "Cycles per day" is below 3,<br />
"OFF" will be shown in the display and data cannot be<br />
entered.<br />
S top time for cycle 3. If "Cycles per day" is below 3,<br />
"OFF" will be shown in the display and data cannot be<br />
entered.<br />
S tart time for cycle 4. If "Cycles per day" is below 4,<br />
"OFF" will be shown in the display and data cannot be<br />
entered.<br />
S top time for cycle 4. If "Cycles per day" is below 4,<br />
"OFF" will be shown in the display and data cannot be<br />
entered.<br />
Based on “<strong>Pool</strong> Volume”, “Turnovers per day” and the total number of hours for Cycle 1 + 2 + 3 + 4<br />
the flow must be calculated:<br />
" <strong>Pool</strong>Volume"<br />
× " Turnovers pr day"<br />
Flow =<br />
Cycle1+<br />
Cycle 2 + Cycle3+<br />
Cycle 4<br />
Note: Only enabled cycles are included in the calculation<br />
IntelliFlo <strong>VF</strong> <strong>Installation</strong> and User’s Guide