Best Practices for Project Management, Design, and Construction of ...

More documents

Recommendations

Info

3.8 Architectural Details Purpose Details developed by the Registered Design Professional are intended to convey construction requirements to the contractors which, when properly constructed, complete the design intent as well as meet the code requirements for structural integrity and life-safety. While it is not possible to provide details that reflect every possible condition of the construction, it is desirable to provide enough details, typical to the various conditions of the project, which establish the minimum construction standards. It is best practice to follow current industry standards when developing these details. For interior partition construction and gypsum ceilings, such standards may include: • CBC, Table 720.1(2) • Gypsum Association, Fire Resistive Design Manual • Leading manufacturers of Gypsum and Metal Stud Products • Metal Stud Manufacturers’ Association (SSMA) • Designs tested and published by an approved testing agency (UL, Intertek, Omega Point, etc.) To further assist in the correct application of interior details for partitions and ceiling construction, OSHPD has established a program of developing pre-approved details which will provide the Registered Design Professional a library of details that, when properly used, meet the structural requirements of California Building Code. For small projects that may be categorized as “Field Review,” “Exempt,” or “Expedited Review,” additional information is provided in the FREER Manual, which provides design criteria for various, minor non-structural work, which a hospital may undertake. Organization and Approach Architectural interior details should be organized, as much as possible, based on subject matter, such as details for structural design, details for fire-resistive construction, and details for non-rated architectural finishes, etc. It is important to provide adequate references on the plans, or in notes, to assist in locating the proper details. General application details may be more appropriate un-referenced on the plans, however, it should be clear where these details apply. Where common standard details are provided for interior partitions, they may be organized in a schedule-type format to allow “tagging” of walls shown on the plans, which reference the various typical construction details. These details may cover required rated construction, acoustical requirements, and typical common construction of chase walls, shaft walls, and walls with radiation shielding. Where fire-resistive partition details are provided, the correct UL, or other testing agency, number must be provided to shown compliance to the intended rating. (OSHPD Best Practices) Page 42 DRAFT FINAL, Sept. 2011
Drawing Content For details that provide information on structural connectors, proper sizing of connectors must be supported by engineering calculations and industry-assigned values, according to the loading on the connection and the Seismic Design Category of the Project. Component identification should also conform to industry nomenclature for structural shapes, sizes and weights—such as the standard designation of studs provided by the SSMA. OSHPD has initiated a Standard Details program, which provides typical details which may be used by the Design Professional. OSHPD Pre-approved Details (OPDs) are available from the FDD Website for use by the Registered Design Professional. The responsibility for the proper use and application of these details remains with the responsible Design Professional. (OSHPD Best Practices) Page 43 DRAFT FINAL, Sept. 2011
Page 1 and 2: [On inside Title Page: Many of the
Page 3 and 4: • Part 1 of Title 24 is the Calif
Page 5 and 6: Rapid Review Unit The Rapid Review
Page 7 and 8: Section 2: Geologic Hazards Investi
Page 9 and 10: equested, CGS will review the suppl
Page 11 and 12: under OSHPD regulations. Please see
Page 13 and 14: Another approach to creating better
Page 15 and 16: create confusion. The discipline ha
Page 17 and 18: applicable phasing must be clearly
Page 19 and 20: addresses, and project Websites, ma
Page 21 and 22: • Plumbing fixture counts for pub
Page 23 and 24: (OSHPD Best Practices) Page 23 DRAF
Page 25 and 26: • Treatment of listed floor slab
Page 27 and 28: • References to the prescriptive
Page 29 and 30: Provisions of California Fire Code
Page 31 and 32: Existing Special Conditions The sam
Page 33 and 34: Enlarged Drawings Provide enlarged
Page 35 and 36: 3.6 Door Schedule Purpose The door
Page 37 and 38: Existing or Special Conditions Exis
Page 39 and 40: approved “shake table testing.”
Page 41: Drawing Content Equipment may inclu
Page 45 and 46: Details that provide information on
Page 47 and 48: Early in the design process, it is
Page 49 and 50: • Identify any equipment that req
Page 51 and 52: • Identify any equipment that req
Page 53 and 54: Several drawings contain essential
Page 55 and 56: o o o o o o o o Floor Plan - Lighti
Page 57 and 58: Section 4: Inspector of Record Best
Page 59 and 60: • Approved program flexes; • Ra
Page 61 and 62: 9. The IOR shall submit verified co
Page 63 and 64: • Log and record areas that by de
Page 65 and 66: • Inspections completed by the us
Page 67 and 68: Logging Inspection Requests 1. When
Page 69 and 70: Preconstruction Meetings A preconst
Page 71 and 72: • Explain code requirements for s
Page 73 and 74: Concluding Remarks An IOR needs to
Page 75 and 76: Although including the TIO Program
Page 77 and 78: Owner The Owner is responsible for
Page 79 and 80: Inspections The TIO Program should
Page 81 and 82: The construction of hospitals in Ca
Page 83 and 84: Instruction Bulletins (IBs), prepar
Page 85 and 86: Changes will undoubtedly be require
Page 87 and 88: Proper execution of these and the o
Page 89 and 90: contingencies, that concur with def
Page 91 and 92: and help in determining the cause o
Page 93 and 94:
have discovered that bids only cove
Page 95 and 96:
Best Practice 7: Determine whether
Page 97 and 98:
OSHPD believes the key to receiving
Page 99 and 100:
the design assistance from the manu
Page 101 and 102:
Permit Phase Best Practice 15: Keep
Page 103 and 104:
Comment and Process Review The deci
Page 105 and 106:
See Section 4 of this volume for a
Page 107 and 108:
• OSHPD shall schedule a final st
Page 109 and 110:
CPC CPR DD Deferred Submittals DSE
Page 111:
(OSHPD Best Practices) Page 111 DRA
show all

Best Practices for Project Management, Design, and Construction of ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?