Pantera SA 2M30 - Frame Grabbers
Pantera SA 2M30 - Frame Grabbers Pantera SA 2M30 - Frame Grabbers
Pantera SA DS -21-02M30 and DS-22-02M30 User’s Manual 12 DALSA 03-32-10150-01
Pantera SA DS -21-02M30 and DS-22-02M30 User’s Manual 13 Camera Hardware Interface 2 2.1 Installation Overview When setting up your camera, you should take these steps: This installation overview assumes you have not installed any system components yet. 1. Power down all equipment. 2. Following the manufacturer’s instructions, install the frame grabber (if applicable). Be sure to observe all static precautions. 3. Install any necessary imaging software. 4. Connect camera body and/or front plate to heat sink. Refer to Thermal Management & Dark Current on page 41 for more information. IMPORTANT: Prior to operation of the Pantera SA 2M30, refer to Section 4.1 Mechanical Interface, for information regarding Thermal Management and Dark Current. 5. Before connecting power to the camera, test all power supplies. Ensure that all the correct voltages are present at the camera end of the power. Power supplies must meet the requirements defined in section 2.4. 6. Inspect all cables and connectors prior to installation. Do not use damaged cables or connectors or the camera may be damaged. 7. Connect Camera Link and power cables. 8. After connecting cables, apply power to the camera. 9. Check the diagnostic LED. See 2.2.1 LED Status Indicator for a description. You must also set up the other components of your system, including light sources, camera mounts, host computers, optics, encoders, and so on. DALSA 03-32-10150-01
- Page 1 and 2: 1.6k x 1.2k Stop Action Area Scan C
- Page 3 and 4: Pantera SA DS -21-02M30 and DS-22-0
- Page 5 and 6: Pantera SA DS -21-02M30 and DS-22-0
- Page 7 and 8: Pantera SA DS -21-02M30 and DS-22-0
- Page 9 and 10: Pantera SA DS -21-02M30 and DS-22-0
- Page 11: Pantera SA DS -21-02M30 and DS-22-0
- Page 15 and 16: Pantera SA DS -21-02M30 and DS-22-0
- Page 17 and 18: Pantera SA DS -21-02M30 and DS-22-0
- Page 19 and 20: Pantera SA DS -21-02M30 and DS-22-0
- Page 21 and 22: Pantera SA DS -21-02M30 and DS-22-0
- Page 23 and 24: Pantera SA DS -21-02M30 and DS-22-0
- Page 25 and 26: Pantera SA DS -21-02M30 and DS-22-0
- Page 27 and 28: Pantera SA DS -21-02M30 and DS-22-0
- Page 29 and 30: Pantera SA DS -21-02M30 and DS-22-0
- Page 31 and 32: Pantera SA DS -21-02M30 and DS-22-0
- Page 33 and 34: Pantera SA DS -21-02M30 and DS-22-0
- Page 35 and 36: Pantera SA DS -21-02M30 and DS-22-0
- Page 37 and 38: Pantera SA DS -21-02M30 and DS-22-0
- Page 39 and 40: Pantera SA DS -21-02M30 and DS-22-0
- Page 41 and 42: Pantera SA DS -21-02M30 and DS-22-0
- Page 43 and 44: Pantera SA DS -21-02M30 and DS-22-0
- Page 45 and 46: Pantera SA DS -21-02M30 and DS-22-0
- Page 47 and 48: Pantera SA DS -21-02M30 and DS-22-0
- Page 49 and 50: Pantera SA DS -21-02M30 and DS-22-0
- Page 51 and 52: Pantera SA DS -21-02M30 and DS-22-0
- Page 53 and 54: Pantera SA DS -21-02M30 and DS-22-0
- Page 55 and 56: Pantera SA DS -21-02M30 and DS-22-0
- Page 57 and 58: Pantera SA DS -21-02M30 and DS-22-0
- Page 59 and 60: Pantera SA DS -21-02M30 and DS-22-0
- Page 61 and 62: Pantera SA DS -21-02M30 and DS-22-0
<strong>Pantera</strong> <strong>SA</strong> DS -21-0<strong>2M30</strong> and DS-22-0<strong>2M30</strong> User’s Manual 13<br />
Camera Hardware<br />
Interface<br />
2<br />
2.1 Installation Overview<br />
When setting up your camera, you should take these steps:<br />
This installation<br />
overview assumes you<br />
have not installed any<br />
system components yet.<br />
1. Power down all equipment.<br />
2. Following the manufacturer’s instructions, install the frame grabber (if applicable). Be<br />
sure to observe all static precautions.<br />
3. Install any necessary imaging software.<br />
4. Connect camera body and/or front plate to heat sink. Refer to Thermal Management<br />
& Dark Current on page 41 for more information. IMPORTANT: Prior to operation of<br />
the <strong>Pantera</strong> <strong>SA</strong> <strong>2M30</strong>, refer to Section 4.1 Mechanical Interface, for information<br />
regarding Thermal Management and Dark Current.<br />
5. Before connecting power to the camera, test all power supplies. Ensure that all the<br />
correct voltages are present at the camera end of the power. Power supplies must<br />
meet the requirements defined in section 2.4.<br />
6. Inspect all cables and connectors prior to installation. Do not use damaged cables or<br />
connectors or the camera may be damaged.<br />
7. Connect Camera Link and power cables.<br />
8. After connecting cables, apply power to the camera.<br />
9. Check the diagnostic LED. See 2.2.1 LED Status Indicator for a description.<br />
You must also set up the other components of your system, including light sources,<br />
camera mounts, host computers, optics, encoders, and so on.<br />
DAL<strong>SA</strong> 03-32-10150-01