Spyder 3 Camera User's Manual GigE Dual Line - Frame Grabbers
Spyder 3 Camera User's Manual GigE Dual Line - Frame Grabbers Spyder 3 Camera User's Manual GigE Dual Line - Frame Grabbers
102 Spyder 3 GigE User Manual Mnemonic Syntax Parameters Description set video mode svm i Switch between normal video mode and camera test patterns: 0: Normal video mode 1: Camera test pattern 2: Camera test pattern update gain reference ugr Changes 0dB gain to equal the current analog gain value set with the sag command. verify temperature vt Check the internal temperature of the camera verify voltage vv Check the camera’s input voltages and return OK or fail write FPN coefficients wfc i Write all current FPN coefficients to EEROM where i is: 1 = FPN coefficient set one 2 = FPN coefficient set two 3 = FPN coefficient set one 4 = FPN coefficient set two write PRNU coeffs wpc i Write all current PRNU coefficients to EEROM where i is: 1 = PRNU coefficient set one 2 = PRNU coefficient set two 3 = PRNU coefficient set one 4 = PRNU coefficient set two write user settings wus Write all of the user settings to EEROM. 03-032-10158-06 DALSA
Spyder 3 GigE User’s Manual 103 A5 Error Handling The following table lists warning and error messages and provides a description and possible cause. Warning messages are returned when the camera cannot meet the full value of the request; error messages are returned when the camera is unable to complete the request. Table 15: Warning and Error Messages Message Description OK> Warning 01: Outside of specification> Warning 02: Clipped to min> Warning 03: Clipped to max> Warning 04: Related parameters adjusted> Warning 05: Can’t set LVDS for this GPIO signal Warning 07: Coefficient may be inaccurate A/D clipping has occurred> Warning 08: Greater than 1% of coefficients have been clipped> Warning 09: Internal line rate inconsistent with readout time> Message Error 02: Unrecognized command> Error 03: Incorrect number of parameters> Error 04: Incorrect parameter value> Error 05: Command unavailable in this mode> SUCCESS Parameter accepted was outside of specified operating range (e.g. gain greater than ±10 dB of factory setting). Parameter was clipped to the current operating range. Use gcp to see value used. Parameter was clipped to the current operating range. Use gcp to see value used. Parameter was clipped to the current operating range. Use gcp to see value used. Input 3 and Output 3 cannot be set to use an LVDS signal. In the region of interest (ROI) greater than 6.251% single or 1% of averaged pixel values were zero or saturated. A FPN/PRNU has been calculated to be greater than the maximum allowable 511 (8). Description Command is not available in the current access level or it is not a valid command. This response returned for · Alpha received for numeric or vice versa · Not an element of the set of possible values. E.g., Baud Rate · Outside the range limit Command is valid at this level of access, but not effective. Eg line rate when in smart EXSYNC mode DALSA 03-032-10158-06
- Page 51 and 52: Spyder 3 GigE User’s Manual 51 en
- Page 53 and 54: Spyder 3 GigE User’s Manual 53 Ap
- Page 55 and 56: Spyder 3 GigE User’s Manual 55 Pa
- Page 57 and 58: Spyder 3 GigE User’s Manual 57 A1
- Page 59 and 60: Spyder 3 GigE User’s Manual 59 Mo
- Page 61 and 62: Spyder 3 GigE User’s Manual 61 Se
- Page 63 and 64: Spyder 3 GigE User’s Manual 63 A1
- Page 65 and 66: ccg, Spyder 3 GigE User’s Manual
- Page 67 and 68: Spyder 3 GigE User’s Manual 67 To
- Page 69 and 70: Spyder 3 GigE User’s Manual 69 Pu
- Page 71 and 72: Spyder 3 GigE User’s Manual 71 Fo
- Page 73 and 74: Spyder 3 GigE User’s Manual 73 Di
- Page 75 and 76: Spyder 3 GigE User’s Manual 75 Pe
- Page 77 and 78: Spyder 3 GigE User’s Manual 77 cp
- Page 79 and 80: Spyder 3 GigE User’s Manual 79 Re
- Page 81 and 82: Spyder 3 GigE User’s Manual 81 Lo
- Page 83 and 84: Spyder 3 GigE User’s Manual 83 A3
- Page 85 and 86: Spyder 3 GigE User’s Manual 85 1
- Page 87 and 88: Spyder 3 GigE User’s Manual 87 Re
- Page 89 and 90: Spyder 3 GigE User’s Manual 89 A4
- Page 91 and 92: Spyder 3 GigE User’s Manual 91 Nu
- Page 93 and 94: Spyder 3 GigE User’s Manual 93 Sy
- Page 95 and 96: Spyder 3 GigE User’s Manual 95 Sy
- Page 97 and 98: Spyder 3 GigE User’s Manual 97 Mn
- Page 99 and 100: Spyder 3 GigE User’s Manual 99 Mn
- Page 101: Spyder 3 GigE User’s Manual 101 M
- Page 105 and 106: Spyder 3 GigE User’s Manual 105 A
- Page 107 and 108: Spyder 3 GigE User’s Manual 107 A
- Page 109 and 110: Spyder 3 GigE User’s Manual 109 D
- Page 111 and 112: Spyder 3 GigE User’s Manual 111 I
- Page 113 and 114: Spyder 3 GigE User’s Manual 113 E
- Page 115 and 116: Spyder 3 GigE User’s Manual 115 A
- Page 117 and 118: Spyder 3 GigE User’s Manual 117 I
- Page 119: Spyder 3 GigE User’s Manual 119 s
<strong>Spyder</strong> 3 <strong>GigE</strong> User’s <strong>Manual</strong><br />
103<br />
A5 Error Handling<br />
The following table lists warning and error messages and provides a description and<br />
possible cause. Warning messages are returned when the camera cannot meet the full<br />
value of the request; error messages are returned when the camera is unable to complete<br />
the request.<br />
Table 15: Warning and Error Messages<br />
Message<br />
Description<br />
OK><br />
Warning 01: Outside<br />
of specification><br />
Warning 02: Clipped<br />
to min><br />
Warning 03: Clipped<br />
to max><br />
Warning 04: Related<br />
parameters<br />
adjusted><br />
Warning 05: Can’t<br />
set LVDS for this<br />
GPIO signal<br />
Warning 07:<br />
Coefficient may be<br />
inaccurate A/D<br />
clipping has<br />
occurred><br />
Warning 08: Greater<br />
than 1% of<br />
coefficients have<br />
been clipped><br />
Warning 09: Internal<br />
line rate inconsistent<br />
with readout time><br />
Message<br />
Error 02:<br />
Unrecognized<br />
command><br />
Error 03: Incorrect<br />
number of<br />
parameters><br />
Error 04: Incorrect<br />
parameter value><br />
Error 05: Command<br />
unavailable in this<br />
mode><br />
SUCCESS<br />
Parameter accepted was outside of specified operating range (e.g. gain<br />
greater than ±10 dB of factory setting).<br />
Parameter was clipped to the current operating range. Use gcp to see<br />
value used.<br />
Parameter was clipped to the current operating range. Use gcp to see<br />
value used.<br />
Parameter was clipped to the current operating range. Use gcp to see<br />
value used.<br />
Input 3 and Output 3 cannot be set to use an LVDS signal.<br />
In the region of interest (ROI) greater than 6.251% single or 1% of<br />
averaged pixel values were zero or saturated.<br />
A FPN/PRNU has been calculated to be greater than the maximum<br />
allowable 511 (8).<br />
Description<br />
Command is not available in the current access level or it is not a valid<br />
command.<br />
This response returned for<br />
· Alpha received for numeric or vice versa<br />
· Not an element of the set of possible values. E.g., Baud Rate<br />
· Outside the range limit<br />
Command is valid at this level of access, but not effective. Eg line rate<br />
when in smart EXSYNC mode<br />
DALSA 03-032-10158-06