Models SRJ-7 and HRJ-7 Juno Survey Meters
Models SRJ-7 and HRJ-7 Juno Survey Meters
Models SRJ-7 and HRJ-7 Juno Survey Meters
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
4M- 10/58<br />
Bullefin No. 744<br />
INSTRUMENTATION FOR NUCLEAR RESEARCH<br />
IONIZATION CHAMBERS (MODELS IC-1 <strong>and</strong> IC-2)<br />
CONNECTOR<br />
I<br />
APPLICATION: These ionization chambers are used for detection <strong>and</strong><br />
measurement of Beta <strong>and</strong> Gamma radiation or Gamma radiation only. They<br />
can be installed in “hot” locations in a laboratory or reactor installation<br />
where it is desirable to monitor for control, health, or safety purposes.<br />
Model IC-1 has approximately one-half of the wall area cut away in the<br />
form of four windows which are fitted with .005” thick cellulose acetate.<br />
It is sensitive to soft radiation <strong>and</strong> is used for the detection <strong>and</strong> measurement<br />
of Beta <strong>and</strong> Gamma radiation. Model IC-2 is of solid wall construction<br />
<strong>and</strong> is used for the detection <strong>and</strong> measurement of Gamma radiation.<br />
CONSTRUCTION: These chambers consist of a bakelite tube 5” in diameter<br />
x 18%’’ long, with bakelite end plates. One end plate holds the high voltage<br />
input <strong>and</strong> signal output connectois. At the other end of the chamber, a<br />
space is provided to hold a dessicant to assui’e reliable operation under<br />
conditions of high humidity. Silica jell is used as the dessicant <strong>and</strong> is<br />
supplied in a cloth bag suitable for inseltion in the cavity provided.<br />
The collectoi, is an aluminum tube Yi’’ in diameter x 17%” long, <strong>and</strong><br />
is supported by Teflon insulation .at the back end, <strong>and</strong> by polystyrene<br />
insulation at the connector end. Guard rings are pi’ovided at either end to<br />
fuither reduce leakage. Leakage resistance is 10:’ ohms or higher to eithei.<br />
ground or high voltage.<br />
The inside of the 5” cylinder <strong>and</strong> the inside of the end plates are coated<br />
with aquadag to form a conducting surface. The aquadag coating is connected<br />
to the high voltage input connector. The electrical continuity resistance<br />
of the aquadag coating is held to less than 5000 ohms.<br />
Cai.eful craftsmanship thi.oughout assembly <strong>and</strong> testing insures<br />
that i.igid insulation specifications are maintained<br />
INQUIRIES INVITED<br />
In addition to the types<br />
SPEClFlCATlONS :<br />
OPERATING VOLTAGE RANGE: 275 to 325 volts D.C.<br />
described. Technical Associates<br />
- SENSITIVITY: Less than 1 mr/hr with micro-micro ammeter<br />
is prepared to supply ionization<br />
on 0.1 volt 10-11 ampere range.<br />
chambers for special purposes to<br />
* ENERGY DEPENDENCE: Small corrective factor below 0.3 mev;<br />
customer specifications.<br />
flat above 0.3 mev.<br />
* OIMENSIDNS: 5” dia. x 20” long. WEIGHT: Net 3 Ibs. Shipping 6 Ibs.<br />
TA<br />
TECHNICAL ASSOCIATES<br />
140 WEST PROVIDENCIA AVENUE BURBANK, CALIFORNIA