UM EN FLX ASI SYS PRO INST - Onlinecomponents.com

More documents

Recommendations

Info

UM EN FLX ASI SYS PRO INST Interference – Signal and power supply cables should not be installed in parallel. If necessary, metal isolating segments should be placed between the power supply and signal cables. – During installation, all connector interlocks must be firmly tightened to ensure the best possible contact. Cable routing in control cabinets – Install AS-i cables in separate cable ducts. – Install AS-i cables with a minimum distance of 10 cm to power cables. Cable routing in buildings – Where possible, use metal cable hangers. – Install AS-i cables as far away as possible from sources of interference, for example, motors and welding equipment. 6.1 Interference Suppression Measures Phoenix Contact recommends connecting relay coils or motor coils with an RC element to protect the devices against interference. Depending on the application, the delay time of the relay can be increased by approximately 1 ms. Figure 6-1 5001B301 Relay coil with RC element For the sizing of the RC element the following values are recommended: R = 100 Ω to 200 Ω; C=220nFto470nF. onlinecomponents.com 6-2 PHOENIX CONTACT 7513_en_01
6.2 Installation Instructions General Information About Installation Electrostatic discharge The device contains components that can be damaged or destroyed by electrostatic discharge. When handling the device, observe the necessary safety precautions against electrostatic discharge (ESD) according to EN 61340-5-1 and EN 61340-5-2. NOTE: The device may only be installed and removed by qualified personnel while observing the ESD regulations. NOTE: Ensure IP65/67 protection To ensure IP65/67 protection, cover unused connections with protective caps. NOTE: Avoid damage to the electronics Only supply the sensors of FLX ASI M8 and FLX ASI M12 devices with the voltage U LS provided at the terminal points. NOTE: Avoid polarity reversal Avoid polarity reversal of the supply voltages U LS and U AUX . 6.3 Mounting Distances No specific distances must be observed between devices or between a device and a cabinet door or cover. Mounting distances are determined solely by the connectors used and the bending radii of the cables. onlinecomponents.com 7513_en_01 PHOENIX CONTACT 6-3
Page 1 and 2:
AUTOMATION User Manual onlinecompon
Page 3 and 4:
AUTOMATION User Manual Configuring
Page 5 and 6:
UM EN FLX ASI SYS PRO General terms
Page 7 and 8:
Table of Contents 1 Fieldline Exten
Page 9 and 10:
Table of Contents 4.2.5 Connecting
Page 11 and 12:
Fieldline Extension and the AS-Inte
Page 13 and 14:
1.3 Documentation for AS-i Devices
Page 15 and 16:
1.5 AS-Interface standardization Fi
Page 17 and 18:
1.6 Different data transmission typ
Page 19 and 20:
! " * ) 4 + ! ! " " 4 , 7 7 5
Page 21 and 22:
AS-Interface Masters/Gateways 2 AS-
Page 23 and 24:
AS-Interface Masters/Gateways 2.1.2
Page 25 and 26:
AS-Interface Masters/Gateways Snapp
Page 27 and 28:
2.1.6 Power Supply and AS-i Connect
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
AS-Interface Masters/Gateways Conne
Page 35 and 36:
PROFIBUS AS-Interface Masters/Gatew
Page 37 and 38: AS-Interface Masters/Gateways AS-i
Page 39 and 40: 2.3.5 Connecting the Master FLX ASI
Page 41 and 42: 2.3.7 Diagnostic and Status Indicat
Page 43 and 44: Power Supply Units 3 Power Supply U
Page 45 and 46: Power Supply Units 3.4 Housing Dime
Page 47 and 48: Power Supply Units 3.5.2 Mounting o
Page 49 and 50: Slaves 4 Slaves Up to 62 slaves can
Page 51 and 52: Slaves 4.1.2 Housing Dimensions of
Page 53 and 54: Slaves 4.1.4 Mounting Fieldline Ext
Page 55 and 56: Slaves 4.1.5 Flat-Ribbon Cable A ke
Page 57 and 58: Slaves 4.1.7 Connecting AS-Interfac
Page 59 and 60: Slaves 4.1.9 Labeling Fieldline Ext
Page 61 and 62: Slaves 4.1.11 Setting the Address f
Page 63 and 64: Slaves 4.2 Description for Fieldlin
Page 65 and 66: Slaves 4.2.2 Housing Dimensions of
Page 67 and 68: Slaves 4.2.4 Mounting Fieldline Ext
Page 69 and 70: Slaves 4.2.7 Pin Assignment of the
Page 73 and 74: Slaves 4.3.2 Description for ASI IO
Page 75 and 76: Slaves 4.3.4 Description for ASI IO
Page 77 and 78: Slaves 4.3.8 Terminal Assignment of
Page 81 and 82: Slaves Setting the switch ASI IO ME
Page 83 and 84: Configuration 5 Configuration Befor
Page 85 and 86: Configuration 5.6 Integrating the A
Page 87: 6 General Information About Install
Page 91 and 92: Startup 7 Startup 7.1 Mounting and
show all

UM EN FLX ASI SYS PRO INST - Onlinecomponents.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?