UM EN FLX ASI SYS PRO INST - Onlinecomponents.com

More documents

Recommendations

Info

UM EN FLX ASI SYS PRO INST 4.3.11 Setting the Sensor Power Supply You can specify whether the sensor is to be supplied from the AS-i circuit or from an external power supply. For the ASI IO ME DI 4 AB and ASI IO ME DIO 4/3 modules, proceed as follows: • To release the upper part, press on both tabs (1) one after the other using a screwdriver. • Pull the upper part towards you until you can feel some resistance. Opening the module ASI IO ME DI 4 AB ASI IO ME DIO 4/3 AB Setting the switch ASI IO ME DI 4 AB ASI IO ME DIO 4/3 AB Figure 4-35 % # ! ) # Opening the module • If you are using an external sensor power supply (U EXT = 12 V DC to 30 V DC) set the switch to the "EXT" position. • If you want to supply the sensor from the AS-i circuit set the switch to the "INT" position. The green "INT" LED lights up. CAUTION: Use a PELV power supply The auxiliary voltage for the output supply must be taken from an isolated power supply (PELV according to IEC 60364-4-41). onlinecomponents.com 1 6 - : 6 % # ! ) " Figure 4-36 Setting the switch 4-32 PHOENIX CONTACT 7513_en_01
Slaves Setting the switch ASI IO ME DIO 4/4 AB 1 6 - : 6 Figure 4-37 Setting the switch % # & " ) % • If you are using an external sensor power supply (U EXT = 12 V DC to 30 V DC) set the switch to the "EXT" position. The green "INT" LED does not light up. • If you want to supply the sensor from the AS-i circuit set the switch to the "INT" position. The green "INT" LED lights up. CAUTION: Use a PELV power supply The auxiliary voltages for the input/output supply must be taken from an isolated power supply (PELV according to IEC 60364-4-41). For additional information about the control cabinet modules, please refer to the corresponding data sheets. onlinecomponents.com 7513_en_01 PHOENIX CONTACT 4-33
Page 1 and 2:
AUTOMATION User Manual onlinecompon
Page 3 and 4:
AUTOMATION User Manual Configuring
Page 5 and 6:
UM EN FLX ASI SYS PRO General terms
Page 7 and 8:
Table of Contents 1 Fieldline Exten
Page 9 and 10:
Table of Contents 4.2.5 Connecting
Page 11 and 12:
Fieldline Extension and the AS-Inte
Page 13 and 14:
1.3 Documentation for AS-i Devices
Page 15 and 16:
1.5 AS-Interface standardization Fi
Page 17 and 18:
1.6 Different data transmission typ
Page 19 and 20:
! " * ) 4 + ! ! " " 4 , 7 7 5
Page 21 and 22:
AS-Interface Masters/Gateways 2 AS-
Page 23 and 24:
AS-Interface Masters/Gateways 2.1.2
Page 25 and 26:
AS-Interface Masters/Gateways Snapp
Page 27 and 28:
2.1.6 Power Supply and AS-i Connect
Page 29 and 30: AS-Interface Masters/Gateways 2.1.9
Page 31 and 32: AS-Interface Masters/Gateways 2.2.2
Page 33 and 34: AS-Interface Masters/Gateways Conne
Page 35 and 36: PROFIBUS AS-Interface Masters/Gatew
Page 37 and 38: AS-Interface Masters/Gateways AS-i
Page 39 and 40: 2.3.5 Connecting the Master FLX ASI
Page 41 and 42: 2.3.7 Diagnostic and Status Indicat
Page 43 and 44: Power Supply Units 3 Power Supply U
Page 45 and 46: Power Supply Units 3.4 Housing Dime
Page 47 and 48: Power Supply Units 3.5.2 Mounting o
Page 49 and 50: Slaves 4 Slaves Up to 62 slaves can
Page 51 and 52: Slaves 4.1.2 Housing Dimensions of
Page 53 and 54: Slaves 4.1.4 Mounting Fieldline Ext
Page 55 and 56: Slaves 4.1.5 Flat-Ribbon Cable A ke
Page 57 and 58: Slaves 4.1.7 Connecting AS-Interfac
Page 59 and 60: Slaves 4.1.9 Labeling Fieldline Ext
Page 61 and 62: Slaves 4.1.11 Setting the Address f
Page 63 and 64: Slaves 4.2 Description for Fieldlin
Page 65 and 66: Slaves 4.2.2 Housing Dimensions of
Page 67 and 68: Slaves 4.2.4 Mounting Fieldline Ext
Page 69 and 70: Slaves 4.2.7 Pin Assignment of the
Page 71 and 72: Slaves 4.2.10 Setting the Address f
Page 73 and 74: Slaves 4.3.2 Description for ASI IO
Page 75 and 76: Slaves 4.3.4 Description for ASI IO
Page 77 and 78: Slaves 4.3.8 Terminal Assignment of
Page 79: Slaves 4.3.10 Setting the Address f
Page 83 and 84: Configuration 5 Configuration Befor
Page 85 and 86: Configuration 5.6 Integrating the A
Page 87 and 88: 6 General Information About Install
Page 89 and 90: 6.2 Installation Instructions Gener
Page 91 and 92: Startup 7 Startup 7.1 Mounting and
show all

UM EN FLX ASI SYS PRO INST - Onlinecomponents.com

Create successful ePaper yourself

Delete template?

Save as template?