UM EN FLX ASI SYS PRO INST - Onlinecomponents.com

More documents

Recommendations

Info

UM EN FLX ASI SYS PRO INST 4.2.5 Connecting AS-Interface and the Auxiliary Voltage AUX to M8 Devices For Fieldline Extension AS-i M8 devices, the AS-i bus and the power supply are connected via an M12 female connector. Fieldline Extension AS-i output devices also require the auxiliary voltage AUX, which is likewise connected via this M12 female connector. Connection All supply voltages are connected via an M12 connector. 4.2.6 Pin Assignment of the AS-i Connection Figure 4-22 Pin assignment of the AS-i connection Pin AS-i and AUX 1 AS-i + 2 AUX- 3 AS-i - 4 AUX+ onlinecomponents.com 4-20 PHOENIX CONTACT 7513_en_01
Slaves 4.2.7 Pin Assignment of the Inputs and Outputs " Figure 4-23 ! $ ! % # ) " Pin assignment of the inputs and outputs Pin Female Input Connector Female Output Connector 1 30 V U S supply voltage for sensors Not used 3 0 V 0 V 4 Input Output 4.2.8 Labeling Fieldline Extension AS-i M8 Devices The devices can be labeled next to the bus connection (4 in Figure 4-20) and at every I/O connection. Depending on the device type, five or ten blank marking labels are supplied as standard with the devices. When labeling, proceed as follows: • Complete a labeling field and snap it into the relevant slot. • If you want to replace a labeling field, it can be removed using a small screwdriver. For professional labeling, Phoenix Contact offers the CMS-MARK-WIN software (see Phoenix Contact CLIPLINE catalog). onlinecomponents.com 7513_en_01 PHOENIX CONTACT 4-21
Page 1 and 2:
AUTOMATION User Manual onlinecompon
Page 3 and 4:
AUTOMATION User Manual Configuring
Page 5 and 6:
UM EN FLX ASI SYS PRO General terms
Page 7 and 8:
Table of Contents 1 Fieldline Exten
Page 9 and 10:
Table of Contents 4.2.5 Connecting
Page 11 and 12:
Fieldline Extension and the AS-Inte
Page 13 and 14:
1.3 Documentation for AS-i Devices
Page 15 and 16:
1.5 AS-Interface standardization Fi
Page 17 and 18: 1.6 Different data transmission typ
Page 19 and 20: ! " * ) 4 + ! ! " " 4 , 7 7 5
Page 21 and 22: AS-Interface Masters/Gateways 2 AS-
Page 23 and 24: AS-Interface Masters/Gateways 2.1.2
Page 25 and 26: AS-Interface Masters/Gateways Snapp
Page 27 and 28: 2.1.6 Power Supply and AS-i Connect
Page 33 and 34: AS-Interface Masters/Gateways Conne
Page 35 and 36: PROFIBUS AS-Interface Masters/Gatew
Page 37 and 38: AS-Interface Masters/Gateways AS-i
Page 39 and 40: 2.3.5 Connecting the Master FLX ASI
Page 41 and 42: 2.3.7 Diagnostic and Status Indicat
Page 43 and 44: Power Supply Units 3 Power Supply U
Page 45 and 46: Power Supply Units 3.4 Housing Dime
Page 47 and 48: Power Supply Units 3.5.2 Mounting o
Page 49 and 50: Slaves 4 Slaves Up to 62 slaves can
Page 51 and 52: Slaves 4.1.2 Housing Dimensions of
Page 53 and 54: Slaves 4.1.4 Mounting Fieldline Ext
Page 55 and 56: Slaves 4.1.5 Flat-Ribbon Cable A ke
Page 57 and 58: Slaves 4.1.7 Connecting AS-Interfac
Page 59 and 60: Slaves 4.1.9 Labeling Fieldline Ext
Page 61 and 62: Slaves 4.1.11 Setting the Address f
Page 63 and 64: Slaves 4.2 Description for Fieldlin
Page 65 and 66: Slaves 4.2.2 Housing Dimensions of
Page 67: Slaves 4.2.4 Mounting Fieldline Ext
Page 73 and 74: Slaves 4.3.2 Description for ASI IO
Page 75 and 76: Slaves 4.3.4 Description for ASI IO
Page 77 and 78: Slaves 4.3.8 Terminal Assignment of
Page 81 and 82: Slaves Setting the switch ASI IO ME
Page 83 and 84: Configuration 5 Configuration Befor
Page 85 and 86: Configuration 5.6 Integrating the A
Page 87 and 88: 6 General Information About Install
Page 89 and 90: 6.2 Installation Instructions Gener
Page 91 and 92: Startup 7 Startup 7.1 Mounting and
show all

UM EN FLX ASI SYS PRO INST - Onlinecomponents.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?