UM EN FLX ASI SYS PRO INST - Onlinecomponents.com

More documents

Recommendations

Info

UM EN FLX ASI SYS PRO INST 4.1.12 Replacing the Electronics Module If in the event of servicing it is necessary to replace the electronics module, proceed as follows: • Release the locking latch (A). • Remove the electronics module from the mounting base (B). • Make sure the arrows on the side of the electronics module and mounting base line up when snapping the electronics module onto the mounting base with the locking latch open (C). A B B C 7513A033 7513A034 7513A035 onlinecomponents.com 7513A032 Figure 4-16 Replacing the electronics module 4-14 PHOENIX CONTACT 7513_en_01
Slaves 4.2 Description for Fieldline Extension AS-i M8 Devices Versions The Fieldline Extension AS-Interface product group includes digital slave devices with the following functions: - DI Digital input devices acquire digital control signals from the process level. These signals are transferred to the higher-level automation equipment via the bus. The signal status is indicated on the device using LEDs. Sensors are connected via M8 screw connectors. The sensors are supplied from the sensor voltage U LS (26.5 V to 31.6 V from AS-Interface). - DIO Digital I/O devices have digital inputs and digital outputs. They acquire digital control signals from the process level. These signals are transferred to the higher-level automation equipment via the bus. Sensors are connected via M8 screw connectors. The sensors are supplied from the sensor voltage U LS (26.5 V to 31.6 V from AS-Interface). Digital I/O devices transfer the digital control signals from the automation equipment to the process level at the actuators. For the specified load currents for the outputs of the various devices, please refer to the data sheet. Actuators are connected via M8 screw connectors. The outputs are short-circuit-proof. The actuators are supplied from the auxiliary voltage U AUX . The signal status is indicated on the device using LEDs. Connection Degree of protection The bus and supply (20 V DC PELV to 30 V DC PELV) are connected via an M12 screw connector using SPEEDCON fast connection technology. The I/O devices are connected via M8 connectors. The devices have IP65/67 protection. onlinecomponents.com 7513_en_01 PHOENIX CONTACT 4-15
Page 1 and 2:
AUTOMATION User Manual onlinecompon
Page 3 and 4:
AUTOMATION User Manual Configuring
Page 5 and 6:
UM EN FLX ASI SYS PRO General terms
Page 7 and 8:
Table of Contents 1 Fieldline Exten
Page 9 and 10:
Table of Contents 4.2.5 Connecting
Page 11 and 12: Fieldline Extension and the AS-Inte
Page 13 and 14: 1.3 Documentation for AS-i Devices
Page 15 and 16: 1.5 AS-Interface standardization Fi
Page 17 and 18: 1.6 Different data transmission typ
Page 19 and 20: ! " * ) 4 + ! ! " " 4 , 7 7 5
Page 21 and 22: AS-Interface Masters/Gateways 2 AS-
Page 23 and 24: AS-Interface Masters/Gateways 2.1.2
Page 25 and 26: AS-Interface Masters/Gateways Snapp
Page 27 and 28: 2.1.6 Power Supply and AS-i Connect
Page 33 and 34: AS-Interface Masters/Gateways Conne
Page 35 and 36: PROFIBUS AS-Interface Masters/Gatew
Page 37 and 38: AS-Interface Masters/Gateways AS-i
Page 39 and 40: 2.3.5 Connecting the Master FLX ASI
Page 41 and 42: 2.3.7 Diagnostic and Status Indicat
Page 43 and 44: Power Supply Units 3 Power Supply U
Page 45 and 46: Power Supply Units 3.4 Housing Dime
Page 47 and 48: Power Supply Units 3.5.2 Mounting o
Page 49 and 50: Slaves 4 Slaves Up to 62 slaves can
Page 51 and 52: Slaves 4.1.2 Housing Dimensions of
Page 53 and 54: Slaves 4.1.4 Mounting Fieldline Ext
Page 55 and 56: Slaves 4.1.5 Flat-Ribbon Cable A ke
Page 57 and 58: Slaves 4.1.7 Connecting AS-Interfac
Page 59 and 60: Slaves 4.1.9 Labeling Fieldline Ext
Page 61: Slaves 4.1.11 Setting the Address f
Page 65 and 66: Slaves 4.2.2 Housing Dimensions of
Page 67 and 68: Slaves 4.2.4 Mounting Fieldline Ext
Page 69 and 70: Slaves 4.2.7 Pin Assignment of the
Page 71 and 72: Slaves 4.2.10 Setting the Address f
Page 73 and 74: Slaves 4.3.2 Description for ASI IO
Page 75 and 76: Slaves 4.3.4 Description for ASI IO
Page 77 and 78: Slaves 4.3.8 Terminal Assignment of
Page 79 and 80: Slaves 4.3.10 Setting the Address f
Page 81 and 82: Slaves Setting the switch ASI IO ME
Page 83 and 84: Configuration 5 Configuration Befor
Page 85 and 86: Configuration 5.6 Integrating the A
Page 87 and 88: 6 General Information About Install
Page 89 and 90: 6.2 Installation Instructions Gener
Page 91 and 92: Startup 7 Startup 7.1 Mounting and
show all

UM EN FLX ASI SYS PRO INST - Onlinecomponents.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?