UM EN FLX ASI SYS PRO INST - Onlinecomponents.com

More documents

Recommendations

Info

UM EN FLX ASI SYS PRO INST DIN rail mounting Mounting • Place the device with the bottom metal edge (1) on the DIN rail. • Push the device forwards (A) until it snaps onto the DIN rail. A Figure 4-6 Snapping the device onto the DIN rail Removing • Push the device forwards (B). • At the same time, push the device down (C), until it detaches from the DIN rail. Figure 4-7 7513A036 Removing the device from the DIN rail onlinecomponents.com 1 B C 7513A037 4-6 PHOENIX CONTACT 7513_en_01
Slaves 4.1.5 Flat-Ribbon Cable A key electromechanical feature of AS-Interface is the flat-ribbon cable. This cable design is used because the AS-i cable should be contacted where possible without cutting off or stripping the sheath. In order to avoid the risk of polarity reversal of the wires, the flat-ribbon cable has a keyway at one end. Unless forced mechanically, the cable cannot be inserted incorrectly in the cable routing aids, which prevents unintentional polarity reversal. The trapezoidal cross-section of the cable makes it easier to seal the cable in the devices, thus providing IP67 protection. In addition to the mechanical keying, both wires in the flat-ribbon cable are color-coded: the positive cable has brown sheathing and the negative cable has light blue sheathing. The external sheath is usually yellow, and when the same cable type is used for the external auxiliary voltage of output devices with 24 V DC a black sheath is used. Figure 4-8 2.5 3.6 7 10 AS-i flat-ribbon cable The cable sheath can consist of various different types of insulation material. For normal rubber cable, the sheath ensures that it automatically closes any contact points that have opened again. This effect is known as self-healing. This means that multiple contact and release is possible at the same point without adversely affecting the seal and the cable insulation. Other cable materials are also available, which have a high level of resistance to chemicals and can permanently withstand UV light. However, the selected material does affect the mechanical properties of the outer cable sheath. onlinecomponents.com 0.5 2 4 7513A012 7513_en_01 PHOENIX CONTACT 4-7
Page 1 and 2:
AUTOMATION User Manual onlinecompon
Page 3 and 4: AUTOMATION User Manual Configuring
Page 5 and 6: UM EN FLX ASI SYS PRO General terms
Page 7 and 8: Table of Contents 1 Fieldline Exten
Page 9 and 10: Table of Contents 4.2.5 Connecting
Page 11 and 12: Fieldline Extension and the AS-Inte
Page 13 and 14: 1.3 Documentation for AS-i Devices
Page 15 and 16: 1.5 AS-Interface standardization Fi
Page 17 and 18: 1.6 Different data transmission typ
Page 19 and 20: ! " * ) 4 + ! ! " " 4 , 7 7 5
Page 21 and 22: AS-Interface Masters/Gateways 2 AS-
Page 23 and 24: AS-Interface Masters/Gateways 2.1.2
Page 25 and 26: AS-Interface Masters/Gateways Snapp
Page 27 and 28: 2.1.6 Power Supply and AS-i Connect
Page 33 and 34: AS-Interface Masters/Gateways Conne
Page 35 and 36: PROFIBUS AS-Interface Masters/Gatew
Page 37 and 38: AS-Interface Masters/Gateways AS-i
Page 39 and 40: 2.3.5 Connecting the Master FLX ASI
Page 41 and 42: 2.3.7 Diagnostic and Status Indicat
Page 43 and 44: Power Supply Units 3 Power Supply U
Page 45 and 46: Power Supply Units 3.4 Housing Dime
Page 47 and 48: Power Supply Units 3.5.2 Mounting o
Page 49 and 50: Slaves 4 Slaves Up to 62 slaves can
Page 51 and 52: Slaves 4.1.2 Housing Dimensions of
Page 53: Slaves 4.1.4 Mounting Fieldline Ext
Page 57 and 58: Slaves 4.1.7 Connecting AS-Interfac
Page 59 and 60: Slaves 4.1.9 Labeling Fieldline Ext
Page 61 and 62: Slaves 4.1.11 Setting the Address f
Page 63 and 64: Slaves 4.2 Description for Fieldlin
Page 65 and 66: Slaves 4.2.2 Housing Dimensions of
Page 67 and 68: Slaves 4.2.4 Mounting Fieldline Ext
Page 69 and 70: Slaves 4.2.7 Pin Assignment of the
Page 73 and 74: Slaves 4.3.2 Description for ASI IO
Page 75 and 76: Slaves 4.3.4 Description for ASI IO
Page 77 and 78: Slaves 4.3.8 Terminal Assignment of
Page 81 and 82: Slaves Setting the switch ASI IO ME
Page 83 and 84: Configuration 5 Configuration Befor
Page 85 and 86: Configuration 5.6 Integrating the A
Page 87 and 88: 6 General Information About Install
Page 89 and 90: 6.2 Installation Instructions Gener
Page 91 and 92: Startup 7 Startup 7.1 Mounting and
show all

UM EN FLX ASI SYS PRO INST - Onlinecomponents.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?