interbus - Onlinecomponents.com

More documents

Recommendations

Info

0D60 Code Type Description and Remedy 0D60 DEV 0D61 0D62 0D63 0D64 DEV 0D65 0D66 0D67 0D68 DEV 0D69 0D6A 0D6B 0D6C DEV 0D6D 0D6E 0D6F 0D70 DEV 0D71 0D72 0D73 An error was detected at the unused, outgoing interface (OUT1) of the indicated device. Remedy: Check the device and replace if necessary. Add_Error_Info: Error location (Segment . Position). An error was detected at the unused, branching interface (OUT1) of the indicated device. Remedy: Check the device and replace if necessary. Add_Error_Info: Error location (Segment . Position). The transmission time for I/O data was exceeded on the indicated device (I/O timeout). Add_Error_Info: Error location (Segment . Position). The indicated device executed a reset due to a fault or insufficient voltage supply. Remedy: See Error Code 0C6C on page 87. Add_Error_Info: Error location (Segment . Position). The controller board tried to start up the bus before all devices were ready for operation. Remedy: – Replace the device. – Delay the call of the "Activate_Configuration" service (0711 hex ). – Increase the startup delay using CMD software. Add_Error_Info: Error location (Segment . Position). onlinecomponents.com 0D74 DEV 0D75 0D76 0D77 Data transmission was aborted. Incorrect operating mode set for the indicated device. Remedy: Set a valid operating mode or replace the device. Add_Error_Info: Error location (Segment . Position). 96 5277CC01
0D9B Code Type Description and Remedy 0D78 LB 0D79 LB 0D7E LB If the dynamic PCP channel is switched on, the data length of the indicated device is not identical to the configuration frame (“ page 116). Add_Error_Info: Error location (Segment . Position). If the dynamic PCP channel is switched on, the ID code of the indicated device is not identical to the configuration frame (“ page 116). Add_Error_Info: Error location (Segment . Position). The INTERBUS protocol chip in the indicated device cannot be operated in the specified configuration, as it does not support the necessary functions. Remedy: Replace the device. 0D80 OUT1 Multiple errors at the outgoing bus interface 0D81 (OUT1) of the indicated device. 0D82 Remedy: See Error Code 0C80 on page 89. 0D83 Add_Error_Info: Error location (Segment . Position). 0D84 OUT1 Multiple errors (timeout) at the outgoing bus 0D85 interface (OUT1) of the indicated device. 0D86 Remedy: See Error Code 0D80. 0D87 Add_Error_Info: Error location (Segment . Position). 0D88 OUT1 Devices were found at the outgoing bus interface 0D89 (OUT1) of the indicated device, which have not 0D8A been configured. This may also apply to 0D8B INTERBUS cables to which no device is connected. Add_Error_Info: Error location (Segment . Position). onlinecomponents.com 0D8C OUT1 0D8D 0D8E 0D8F The bus can be read but not started up. Remedy: See Error Code 0C8C on page 89. Add_Error_Info: Error location (Segment . Position). 0D98 OUT1 See Error Code 0C98 on page 90. 0D99 0D9A 0D9B 5277CC01 97
Page 1 and 2:
Designation: Revision: Order No.: I
Page 3 and 4:
Information About This Guide Depend
Page 5 and 6:
Table of Contents Error Localizatio
Page 7 and 8:
Diagnostic Display 1 6 - 4 * 7 5 F
Page 9 and 10:
% The displayed number is a percent
Page 11 and 12:
Diagnostics Without Display On cont
Page 13 and 14:
SYSFAIL Yellow STOP ON TR UL US Gre
Page 15 and 16:
Diagnostic Parameter Registers The
Page 17 and 18:
INTERBUS Startup Troubleshooting Us
Page 19 and 20:
MODE - CFG MODE Menu CFG Menu (Conf
Page 21 and 22:
MODE - CFG SAVE CFG Saving the Conf
Page 23 and 24:
MODE - DIAG USER Line 1 - USER - Us
Page 25 and 26:
MODE - DIAG DEBG Menu Item (Debug)
Page 27 and 28:
MODE - DIAG 3.2 Unsuccessful Start
Page 29 and 30:
MODE - STAT STAT Menu (Statistics)
Page 31 and 32:
MODE - STAT CRC Menu Item (Transmis
Page 33 and 34:
MODE - OPT RSET Menu Item (Reset) O
Page 35 and 36:
Error Localization If a bus error o
Page 37 and 38:
Remote Bus Error (RBUS) , E= C I
Page 39 and 40:
When detecting a local bus error, d
Page 41 and 42:
transmission paths between these de
Page 43 and 44:
OUT 2 Interface Error , E= C I JE
Page 45 and 46:
Local Bus Error in an Inline Statio
Page 47 and 48: Device Error (DEV) , E= C I JE? I
Page 49 and 50: EVENT Message (EVNT) , E= C I JE?
Page 51 and 52: Error Codes 0BE4 Code Type Descript
Page 53 and 54: 0913 Code Type Description and Reme
Page 55 and 56: 092A Code Type Description and Reme
Page 57 and 58: 093B Code Type Description and Reme
Page 61 and 62: 09DB Code Type Description and Reme
Page 63 and 64: 0A05 Code Type Description and Reme
Page 65 and 66: 0A1B Code Type Description and Reme
Page 71 and 72: 0A4A Code Type Description and Reme
Page 77 and 78: 0B81 Code Type Description and Reme
Page 79 and 80: 0B90 Code Type Description and Reme
Page 81 and 82: 0BC2 Code Type Description and Reme
Page 83 and 84: 0BE0 Code Type Description and Reme
Page 85 and 86: 0C13 Code Type Description and Reme
Page 87 and 88: 0C4F Code Type Description and Reme
Page 89 and 90: 0C79 Code Type Description and Reme
Page 91 and 92: 0C8F Code Type Description and Reme
Page 93 and 94: 0CCF Code Type Description and Reme
Page 95 and 96: 0D27 Code Type Description and Reme
Page 97: 0D5F Code Type Description and Reme
Page 107 and 108: 202E Code Type Description and Reme
Page 113 and 114: Table 3 Overview of fuse types (Con
Page 115 and 116: Replacing the INTERBUS Controller B
Page 117 and 118: E Red LED ON OFF Error message Erro
Page 119 and 120: Services Offered by Phoenix Contact
Page 121 and 122: Error Description When did the erro
Page 123 and 124: Flowchart for Error Removal - HH H
Page 125 and 126: Phoenix Contact GmbH & Co. KG Flach
show all

interbus - Onlinecomponents.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?