interbus - Onlinecomponents.com
interbus - Onlinecomponents.com interbus - Onlinecomponents.com
0BC3 Code Type Description and Remedy 0BC3 0BC4 0BC5 The protocol chip in a Loop device is too hot. Remedy: Reduce the ambient temperature or provide ventilation for the Loop device. Add_Error_Info: Error location (Segment . Position). The internal current source is overloaded on a Loop device. Remedy: Reduce the number of connected sensors/actuators or check the sensors/actuators for errors. Add_Error_Info: Error location (Segment . Position). The output of the device is overloaded. Remedy: Reduce the number of connected sensors/actuators or check the sensors/actuators for errors. Add_Error_Info: Error location (Segment . Position). 0BD0 USER The controller board could not start up the connected configuration, as no bus configuration is connected. Remedy: Connect the bus configuration. 0BD1 0BD2 EVNT The process data could not be updated within the specified PD cycle time. The controller board indicates this only if it has been activated with the "Set_Value" service (0750 hex ) before. Remedy: Check your system or increase the value set for the PD cycle time using the "Set_Value" service (0750 hex ). The bus warning time has elapsed. No data cycle could be transmitted within the specified bus warning time. Remedy: Check the system or increase the bus warning time with the "Set_Value" service or using CMD or PC WORX software. onlinecomponents.com 0BD4 USER A single bus error occurred. (The controller board indicates this only if this function has been activated before.) 80 5277CC01
0BE0 Code Type Description and Remedy 0BD5 USER An error occurred in the bus segment, which is connected to the branching branch interface of the indicated device. The branching interface was switched off. Add_Error_Info: Device number of the device that was switched off. 0BDB BUS 0BDC 0BDD BUS The process preprocessing task is no longer in the RUN state. The bus was stopped to prevent data transmission without preprocessing. Error in the preprocessing program (e.g.,division by zero) or preprocessing intentionally stopped by the user. A SYSFAIL on the host system generated an alarm stop on the controller board while it was in the ACTIVE or RUN state. (This error message must already be enabled ("Set_Value" service (0750 hex )). The bus was stopped, as inconsistent data could otherwise have been transmitted, e.g.,by a byte access to a 16-bit locked MPM address (“ page 116). Remedy: See Error Code 0B8F on page 77. 0BDE USER A synchronization error occurred in bussynchronous mode. Remedy: Check the system or increase the cycle time with the "Set_Value" service or using CMD or PC WORX software. 0BDF LOOK FOR FAIL A bus error occurred. The controller board has set data transmission and is searching for the error location and error cause. Remedy: Wait for the troubleshooting results. 0BE0 BUS See Error Code E0 on page 49. onlinecomponents.com 5277CC01 81
- Page 31 and 32: MODE - STAT CRC Menu Item (Transmis
- Page 33 and 34: MODE - OPT RSET Menu Item (Reset) O
- Page 35 and 36: Error Localization If a bus error o
- Page 37 and 38: Remote Bus Error (RBUS) , E= C I
- Page 39 and 40: When detecting a local bus error, d
- Page 41 and 42: transmission paths between these de
- Page 43 and 44: OUT 2 Interface Error , E= C I JE
- Page 45 and 46: Local Bus Error in an Inline Statio
- Page 47 and 48: Device Error (DEV) , E= C I JE? I
- Page 49 and 50: EVENT Message (EVNT) , E= C I JE?
- Page 51 and 52: Error Codes 0BE4 Code Type Descript
- Page 53 and 54: 0913 Code Type Description and Reme
- Page 55 and 56: 092A Code Type Description and Reme
- Page 57 and 58: 093B Code Type Description and Reme
- Page 59 and 60: 0953 Code Type Description and Reme
- Page 61 and 62: 09DB Code Type Description and Reme
- Page 63 and 64: 0A05 Code Type Description and Reme
- Page 65 and 66: 0A1B Code Type Description and Reme
- Page 67 and 68: 0A28 Code Type Description and Reme
- Page 69 and 70: 0A35 Code Type Description and Reme
- Page 71 and 72: 0A4A Code Type Description and Reme
- Page 73 and 74: 0A55 Code Type Description and Reme
- Page 75 and 76: 0A64 Code Type Description and Reme
- Page 77 and 78: 0B81 Code Type Description and Reme
- Page 79 and 80: 0B90 Code Type Description and Reme
- Page 81: 0BC2 Code Type Description and Reme
- Page 85 and 86: 0C13 Code Type Description and Reme
- Page 87 and 88: 0C4F Code Type Description and Reme
- Page 89 and 90: 0C79 Code Type Description and Reme
- Page 91 and 92: 0C8F Code Type Description and Reme
- Page 93 and 94: 0CCF Code Type Description and Reme
- Page 95 and 96: 0D27 Code Type Description and Reme
- Page 97 and 98: 0D5F Code Type Description and Reme
- Page 99 and 100: 0D9B Code Type Description and Reme
- Page 101 and 102: 1011 Code Type Description and Reme
- Page 103 and 104: 1217 Code Type Description and Reme
- Page 105 and 106: 2010 Code Type Description and Reme
- Page 107 and 108: 202E Code Type Description and Reme
- Page 109 and 110: 8040 Code Type Description and Reme
- Page 111 and 112: 8400 Code Type Description and Reme
- Page 113 and 114: Table 3 Overview of fuse types (Con
- Page 115 and 116: Replacing the INTERBUS Controller B
- Page 117 and 118: E Red LED ON OFF Error message Erro
- Page 119 and 120: Services Offered by Phoenix Contact
- Page 121 and 122: Error Description When did the erro
- Page 123 and 124: Flowchart for Error Removal - HH H
- Page 125 and 126: Phoenix Contact GmbH & Co. KG Flach
0BC3<br />
Code Type Description and Remedy<br />
0BC3<br />
0BC4<br />
0BC5<br />
The protocol chip in a Loop device is too hot.<br />
Remedy: Reduce the ambient temperature or<br />
provide ventilation for the Loop device.<br />
Add_Error_Info: Error location<br />
(Segment . Position).<br />
The internal current source is overloaded on a<br />
Loop device.<br />
Remedy: Reduce the number of connected<br />
sensors/actuators or check the sensors/actuators<br />
for errors.<br />
Add_Error_Info: Error location<br />
(Segment . Position).<br />
The output of the device is overloaded.<br />
Remedy: Reduce the number of connected<br />
sensors/actuators or check the sensors/actuators<br />
for errors.<br />
Add_Error_Info: Error location<br />
(Segment . Position).<br />
0BD0 USER The controller board could not start up the<br />
connected configuration, as no bus configuration<br />
is connected.<br />
Remedy: Connect the bus configuration.<br />
0BD1<br />
0BD2 EVNT<br />
The process data could not be updated within the<br />
specified PD cycle time. The controller board<br />
indicates this only if it has been activated with the<br />
"Set_Value" service (0750 hex ) before.<br />
Remedy: Check your system or increase the<br />
value set for the PD cycle time using the<br />
"Set_Value" service (0750 hex ).<br />
The bus warning time has elapsed. No data cycle<br />
could be transmitted within the specified bus<br />
warning time.<br />
Remedy: Check the system or increase the bus<br />
warning time with the "Set_Value" service or<br />
using CMD or PC WORX software.<br />
online<strong>com</strong>ponents.<strong>com</strong><br />
0BD4 USER A single bus error occurred. (The controller board<br />
indicates this only if this function has been<br />
activated before.)<br />
80 5277CC01