interbus - Onlinecomponents.com

More documents

Recommendations

Info

8060 Code Type Description and Remedy 8060 The specified device is indicating a short circuit at the output. Add_Error_Info: Error location (Segment . Position: channel). 808x 809x 80A0 80B1 The specified device is indicating a sensor supply error in one or more groups. The "x" stands for a group number and represents a group of four bits, in which each bits represents a group number: 808x 809x Bit 0: Group 1 Group 5 Bit 1: Group 2 Group 6 Bit 2: Group 3 Group 7 Bit 3: Group 4 Group 8 Example: Code 8085 hex indicates that the sensor supply to Group 1 and 3 is faulty. Remedy: Check the group(s) of the specified device. Add_Error_Info: Error location (Segment . Position). The specified device is indicating a voltage supply error in one or more groups. Remedy: Check the group(s) of the specified device. Add_Error_Info: Error location (Segment . Position). The specified device is indicating a configuration error. Remedy: Check the parameters of the specified device. Add_Error_Info: Error location (Segment . Position). onlinecomponents.com 80B2 The specified device is indicating an error in the I/ O electronics of the connected sensors/actuators. Add_Error_Info: Error location (Segment . Position). 108 5277CC01
8400 Code Type Description and Remedy 80B4 The specified device is indicating that the temperature has been exceeded. Remedy: Check the connected sensors and actuators. Add_Error_Info: Error location (Segment . Position). 8400 The specified device is indicating an error at the outgoing interface (OUT2). The error occurred in the lower-level installation local bus. Remedy: Check the modules connected to the specified device. See "Local Bus Error in INTERBUS Loop" on page 42. Add_Error_Info: Error location (Segment . Position). * Applies to IBS 24 ETH DSC/I-T, IBS 24 RFC/486DX/ETH-T, and IBS ISA FC/486DX/I-T. "FC" indicates errors that only occur on Field Controllers. onlinecomponents.com 5277CC01 109
Page 1 and 2:
Designation: Revision: Order No.: I
Page 3 and 4:
Information About This Guide Depend
Page 5 and 6:
Table of Contents Error Localizatio
Page 7 and 8:
Diagnostic Display 1 6 - 4 * 7 5 F
Page 9 and 10:
% The displayed number is a percent
Page 11 and 12:
Diagnostics Without Display On cont
Page 13 and 14:
SYSFAIL Yellow STOP ON TR UL US Gre
Page 15 and 16:
Diagnostic Parameter Registers The
Page 17 and 18:
INTERBUS Startup Troubleshooting Us
Page 19 and 20:
MODE - CFG MODE Menu CFG Menu (Conf
Page 21 and 22:
MODE - CFG SAVE CFG Saving the Conf
Page 23 and 24:
MODE - DIAG USER Line 1 - USER - Us
Page 25 and 26:
MODE - DIAG DEBG Menu Item (Debug)
Page 27 and 28:
MODE - DIAG 3.2 Unsuccessful Start
Page 29 and 30:
MODE - STAT STAT Menu (Statistics)
Page 31 and 32:
MODE - STAT CRC Menu Item (Transmis
Page 33 and 34:
MODE - OPT RSET Menu Item (Reset) O
Page 35 and 36:
Error Localization If a bus error o
Page 37 and 38:
Remote Bus Error (RBUS) , E= C I
Page 39 and 40:
When detecting a local bus error, d
Page 41 and 42:
transmission paths between these de
Page 43 and 44:
OUT 2 Interface Error , E= C I JE
Page 45 and 46:
Local Bus Error in an Inline Statio
Page 47 and 48:
Device Error (DEV) , E= C I JE? I
Page 49 and 50:
EVENT Message (EVNT) , E= C I JE?
Page 51 and 52:
Error Codes 0BE4 Code Type Descript
Page 53 and 54:
0913 Code Type Description and Reme
Page 55 and 56:
092A Code Type Description and Reme
Page 57 and 58:
093B Code Type Description and Reme
Page 59 and 60: 0953 Code Type Description and Reme
Page 61 and 62: 09DB Code Type Description and Reme
Page 63 and 64: 0A05 Code Type Description and Reme
Page 65 and 66: 0A1B Code Type Description and Reme
Page 71 and 72: 0A4A Code Type Description and Reme
Page 77 and 78: 0B81 Code Type Description and Reme
Page 79 and 80: 0B90 Code Type Description and Reme
Page 81 and 82: 0BC2 Code Type Description and Reme
Page 83 and 84: 0BE0 Code Type Description and Reme
Page 85 and 86: 0C13 Code Type Description and Reme
Page 87 and 88: 0C4F Code Type Description and Reme
Page 89 and 90: 0C79 Code Type Description and Reme
Page 91 and 92: 0C8F Code Type Description and Reme
Page 93 and 94: 0CCF Code Type Description and Reme
Page 95 and 96: 0D27 Code Type Description and Reme
Page 97 and 98: 0D5F Code Type Description and Reme
Page 99 and 100: 0D9B Code Type Description and Reme
Page 107 and 108: 202E Code Type Description and Reme
Page 109: 8040 Code Type Description and Reme
Page 113 and 114: Table 3 Overview of fuse types (Con
Page 115 and 116: Replacing the INTERBUS Controller B
Page 117 and 118: E Red LED ON OFF Error message Erro
Page 119 and 120: Services Offered by Phoenix Contact
Page 121 and 122: Error Description When did the erro
Page 123 and 124: Flowchart for Error Removal - HH H
Page 125 and 126: Phoenix Contact GmbH & Co. KG Flach
show all

interbus - Onlinecomponents.com

Create successful ePaper yourself

Delete template?

Save as template?