interbus - Onlinecomponents.com
interbus - Onlinecomponents.com interbus - Onlinecomponents.com
202F Code Type Description and Remedy 202F The maximum number of parameters was exceeded for a service in an SVC file. Remedy: Check the SVC file and reduce the number of parameters. Add_Error_Info: Line number with incorrect entry. 2030 A negative service confirmation was received. 2111* FC Battery supply has failed. The date and time of the realtime clock as well as the retain data may be lost. Remedy: Replace the battery with a new 3.6 V AA lithium battery. 2112* FC The IP address has not yet been parameterized or has the value "0.0.0.0". This warning is always issued for new devices. Remedy: Parameterize the IP address. 2113* FC An error occurred when transmitting configuration data from PC WORX (e.g., connection loss, voltage failure). Remedy: Repeat data transmission. 2211* FC Stack overflow in the task of the IEC 61131 runtime system. Remedy: Increase the stack. 2212* FC Memory exceeded in an array of the IEC 61131 runtime system. Remedy: Check access to the array and increase the size of the array, if necessary. 2214* FC Division by zero in the task of the IEC 61131 runtime system. Remedy: Remove error in the program. onlinecomponents.com 2216* FC Value range exceeded in the task of the IEC 61131 runtime system. Remedy: Remove error in the program. 2217* FC Watchdog released in the task of the IEC 61131 runtime system. Remedy: Remove error in the program. 106 5277CC01
8040 Code Type Description and Remedy 2218* FC Runtime is too long in the task of the IEC 61131 runtime system. Remedy: Remove error in the program. 2219 You called a function block, which does not exist in the firmware or in the IEC 61131 runtime system. 221A 221B 221C 221D*FC One program in the IEC 61131 runtime system was stopped from the program. An unexpected breakpoint occurred. An internal exception occurred. String error. Remedy: Remove error in the program. 221E* FC – Division by zero in the task of the IEC 61131 runtime system. – Watchdog released in the task of the IEC 61131 runtime system. – Execution time is too long. Remedy: Remove error in the program. 2410 to 242B 26xx 6342 Bus error indication Fatal error. For more detailed information, please refer to the IBS SYS FW G4 UM E Firmware Manual, Order No. 27 45 18 5, Revision C or later. An exception occurred at the processor. The loworder byte contains the vector number of the exception. The controller board has detected an error in the connected bus system during INTERBUS operation. The bus cannot be operated any longer. The controller board is searching for the error location. Remedy: Read the error cause using the "Get_Error_Info" service (0316 hex ) or use the diagnostics in the CMD software. onlinecomponents.com 8040 The specified device is indicating a single channel error. Remedy: Check the channel of the specified device. Add_Error_Info: Error location (Segment . Position). 5277CC01 107
- Page 57 and 58: 093B Code Type Description and Reme
- Page 59 and 60: 0953 Code Type Description and Reme
- Page 61 and 62: 09DB Code Type Description and Reme
- Page 63 and 64: 0A05 Code Type Description and Reme
- Page 65 and 66: 0A1B Code Type Description and Reme
- Page 67 and 68: 0A28 Code Type Description and Reme
- Page 69 and 70: 0A35 Code Type Description and Reme
- Page 71 and 72: 0A4A Code Type Description and Reme
- Page 73 and 74: 0A55 Code Type Description and Reme
- Page 75 and 76: 0A64 Code Type Description and Reme
- Page 77 and 78: 0B81 Code Type Description and Reme
- Page 79 and 80: 0B90 Code Type Description and Reme
- Page 81 and 82: 0BC2 Code Type Description and Reme
- Page 83 and 84: 0BE0 Code Type Description and Reme
- Page 85 and 86: 0C13 Code Type Description and Reme
- Page 87 and 88: 0C4F Code Type Description and Reme
- Page 89 and 90: 0C79 Code Type Description and Reme
- Page 91 and 92: 0C8F Code Type Description and Reme
- Page 93 and 94: 0CCF Code Type Description and Reme
- Page 95 and 96: 0D27 Code Type Description and Reme
- Page 97 and 98: 0D5F Code Type Description and Reme
- Page 99 and 100: 0D9B Code Type Description and Reme
- Page 101 and 102: 1011 Code Type Description and Reme
- Page 103 and 104: 1217 Code Type Description and Reme
- Page 105 and 106: 2010 Code Type Description and Reme
- Page 107: 202E Code Type Description and Reme
- Page 111 and 112: 8400 Code Type Description and Reme
- Page 113 and 114: Table 3 Overview of fuse types (Con
- Page 115 and 116: Replacing the INTERBUS Controller B
- Page 117 and 118: E Red LED ON OFF Error message Erro
- Page 119 and 120: Services Offered by Phoenix Contact
- Page 121 and 122: Error Description When did the erro
- Page 123 and 124: Flowchart for Error Removal - HH H
- Page 125 and 126: Phoenix Contact GmbH & Co. KG Flach
202F<br />
Code Type Description and Remedy<br />
202F<br />
The maximum number of parameters was<br />
exceeded for a service in an SVC file.<br />
Remedy: Check the SVC file and reduce the<br />
number of parameters.<br />
Add_Error_Info: Line number with incorrect<br />
entry.<br />
2030 A negative service confirmation was received.<br />
2111* FC Battery supply has failed. The date and time of the<br />
realtime clock as well as the retain data may be<br />
lost.<br />
Remedy: Replace the battery with a new 3.6 V<br />
AA lithium battery.<br />
2112* FC The IP address has not yet been parameterized or<br />
has the value "0.0.0.0". This warning is always<br />
issued for new devices.<br />
Remedy: Parameterize the IP address.<br />
2113* FC An error occurred when transmitting configuration<br />
data from PC WORX (e.g., connection loss,<br />
voltage failure).<br />
Remedy: Repeat data transmission.<br />
2211* FC Stack overflow in the task of the IEC 61131<br />
runtime system.<br />
Remedy: Increase the stack.<br />
2212* FC Memory exceeded in an array of the IEC 61131<br />
runtime system.<br />
Remedy: Check access to the array and increase<br />
the size of the array, if necessary.<br />
2214* FC Division by zero in the task of the IEC 61131<br />
runtime system.<br />
Remedy: Remove error in the program.<br />
online<strong>com</strong>ponents.<strong>com</strong><br />
2216* FC Value range exceeded in the task of the IEC<br />
61131 runtime system.<br />
Remedy: Remove error in the program.<br />
2217* FC Watchdog released in the task of the IEC 61131<br />
runtime system.<br />
Remedy: Remove error in the program.<br />
106 5277CC01