KE-FG-D01VNN0500TSP - Official Electronic

EMI SHIELDING FERRITE
FILTERING
SPLIT FERRITES FOR ROUND CABLE 5-9
FLAT CABLE FERRITES 10-19
ROUND CABLE FERRITES 20-27
FINEMET CORE (F) 28
LOW CUT CORE (TRM) 29
OVAL CORE 30
MULTI APERTURE WOUND BEADS 30
FERRITE PLATES FOR D-SUB AND CPU 31
WOUND BEADS 32-34
FERRITE DESIGN KIT 34
ABSORBING SHEETS 35-36
EMI GROUNDING MATERIAL
GROUNDING
FRAME GROUNDING SPACER 37
GROUNDING CLAMPS 38-39
GROUNDING MESH/STRAPS 40
ON BOARD CONTACTS/CLAMP/CLIP/SOFT CONTACT
LUG TERMINALS 41-46
CONDUCTIVE TAPES 47
TECHNICAL ADHESIVE TAPES FOR SPECIAL APPLICATIONS 48
CONDUCTIVE FABRIC TAPE - CNT 49
EMI SHIELDING MATERIAL
SHIELDING
FABRIC OVER FOAM GASKET 50-54
FOAMGASKET KIT 55
CUSTOMISED GASKET 56
PART NUMBER GUIDE 57
CONDUCTIVE FOAM 58
SHIELDING FABRIC 59-60
D-SUB CONNECTOR-GASKETS 61
CARBON RUBBER 62
CONDUCTIVE ELASTOMER 63-64
ALL METAL GASKETS 65
WIRE MESH OVER ELASTOMER CORE GASKETS 66
MULTISTRIP GASKETS 67
SYNTHETIC YARN KITTED GASKETS 68
SPRING SERIES GASKETS 69
MESH TAPES 70
COPPER BERYLLIUM FINGER STRIPS 71-80
MONOFILAMENT BRAIDED SLEEVING MFS-AG 81-82
GENERAL TERMS OF DELIVERY AND PAYMENT 83-84

QUICK
INDEX
B
BCN 17
C
CB 71-80
CCT 47
CFT-CS 48
CMP-CS 48
CNT 49
CSR-D 62
CSR-P 62
CSR-R 62
CSR-U 62
CSR-O 62
D
DECF 58
E
EFC 17
ESF 34
F
F 28
FCP 16
FGC 38
FGES 37
FGM 40
FGR 38
FGS 37
FGST 40
FH 6/8 30
FH 9/15/25/37 31
FOG 46
FP 18
FPC 14-15
FPCK 16
FPH 11
FPI 14
FPO 14
FRC 10
FRH 10
FRHL 10
H
HPC 39
K
KCF 7
KE-E1/E2/E3/E4 59-60
KE-FG-D 53
KE-FG-F 52
KE-FG-K 54
KE-FG-P 54
KE-FG-R 51-52
KE-FG-W 54
KE-MC 18
KE-PC 19
M
MAB-03 36
MFM 36
MFS-AG 81-82
MG-03A/04/05/06 35
MG-B 65
MG-BE 66
MG-C 70
MG-P 65
MG-PE 66
MG-R 65
MG-RE 66
MG-REDM 63
MG-REM 67
MG-SB 69
MG-SD 69
MG-SP 69
MG-ST 69
MG-T 65
MG-TE 66
MG-YDE 68
MG-YRE 68
MG-YTE 68
N
NK 39
O
OG 41-42
OGC 42
OGCP 42
OGP 44
OG-R 44
OGSC 42
OG-K01/02T 44
OGSS 43
R
R6H 32
RFC 5
RFC-H 5
RH-3.5 33-34
RI 20-21
S
SD 31
SFC 6
SG-FO 64
SG-PL 63
SG-RE 63
SG-RO 64
SG-TU 64
SSC 12
SSH 10
T
TFC 9
TFCM 9
TFP 9
TOG 45
TR 22-23
TRCN 8
TRE 30
TRM 29
U
USB 5

FILTERING
SOLVING EMI PROBLEMS IN DATA TRANSMISSION LINES
FILTERING
Relationship between number of
turns (windings) and impedance
vs. frequency
The graphs shown in the right figure
indicate performance curves of one to
four turns from the bottom to the top,
respectively. As the number of turns is
increased, the impedance is enhanced, but
it is known from this figure that the peaks
of impedance are moved downward as
stray capacitance between lines are increased.
Insertion loss can be increased, particularly
at lower frequencies, by increasing the
number of turns of the wire conductor
through the ferrite device. This will damp
the noise without influencing the signals.
Difference in impedance vs. frequency
between split cores and
one-piece cores
The graph shown in the right side compares
characteristics of separated and nonseparated
cores for toroidal cores of the
same size. Although impedance of a separated
core is lower in the area less than
30 MHz, it is similar to or slightly higher
than that of a non-separated one.
The merit of using the separated cores is
that it may be easily mounted in an
already wired cable or a cable which has
been already connected to a connector
and that magnetic saturation in DC occurs
less frequently than in non-separated
ones when large DC current flows
through a line.
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
4

FILTERING
SPLIT FERRITES FOR ROUND CABLE
patented
Features
- Employ high-performance ferrites
(Nickel-Zinc) effective against high
frequency noise
- Ferrite assembly in fully enclosed Nylon
6/6 case can be installed as a single addon
component by snapping. (UL 94 V-0)
- Designed to help reduce cost and time
to market saving.
- Can be installed in its intended location
before or after product assembly by
snapping.
- Black Plastic case available.
Part No.
USB-4
RFC-4
RFC-5
RFC-6
RFC-7
RFC-8
RFC-9
RFC-10
RFC-13
RFC-H13
RFC-20
A
13,9
14,5
18.5
18.5
15.8
20.6
22.6
26.6
29.6
31.7
40.0
Unit: mm Impedance (Ω) 1 turn Impedance (Ω) 2 turn
B C 25MHz 100MHz 25MHz 100MHz
27.0 13.6 122 168 443 614
28.6 13.8 56 149 198 584
34.0 17.8 53 177 126 864
34.0 17.8 53 177 126 864
20.0 13.8 45 75 -
-
34.0 19.8 49 150 173 658
34.0 21.4 64 183 242 760
34.0 25.4 95 236 371 1036
34.0 28.4 90 209 363 878
41.0
47.0
29.4
40.0
200
180
270
260
-
-
-
-
Max.
Cable Diameter
ø 5,5
ø 4,5
ø 5.5
ø 6.5
ø 7.0
ø 9.0
ø 10.0
ø 11.0
ø 14.0
ø 13.5
ø 20.0
RFC-7
RFC-20
RFC-20
5
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
SPLIT FERRITES FOR ROUND CABLE
patented
Features
- Employ high-performance ferrites
(Nickel-Zinc) effective against high frequency
noise
- Ferrite assembly in fully enclosed Nylon
6/6 case, can be installed as a single addon
component by snapping. (UL 94 V-0)
- Spring stainless steel (SUS 304-CSP)
incorporates ensure a tighter surface contact
between ferrites for a consistent performance.
- Designed to help reduce cost and time
to market saving.
- Can be installed in its intended location
before or after product assembly by snapping.
Part No.
SFC-3
SFC-4
SFC-5
SFC-6
SFC-8
SFC-10
A
13.4
16.3
21.0
23.5
23.5
32.6
Black plastic case available (-BK)
Unit: mm Impedance (Ω) 1 turn Impedance (Ω) 2 turn
B
C 25MHz 100MHz 25MHz 100MHz
18.9 13.2 45 80 163 301
29.5 15.0 96 138 401 522
32.0 17.5 177 242 660 766
32.0 20.0 139 207 614 629
32.0 20.0 137 204 573 663
32.0 29.0 149 266 640 733
Max.
Cable Diameter
ø3
ø4 to ø5
ø5 to ø6
ø6 to ø7
ø7,8 to ø8,5
ø9,5 to ø10,5
FILTERING
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
6

FILTERING
SPLIT FERRITES FOR ROUND CABLE
Features
- Split construction permits easy insertion
on pre-installed cable and installed
or cables with connectors.
- Kept in a plastic case, ferrite will not
crack or chip. (UL 94 V-2)
- Cable is fixed firmly by plastic housing
C
Applications
- For noise problems arising from
office automation equipment or other
digital equipment.
- Internal and external power cable.
- Internal cables between PC boards
and data connectors.
- White Plastic case available.
B
A
Part No.
KCF-50
KCF-65
KCF-100
KCF-130
A
23.0
32.6
32.6
32.7
Unit: mm
B
15.0
17.8
22.5
29.2
C
14.0
19.2
23.0
30.2
Impedance (Ω)
25MHz
100MHz
93
157
176
267
151
226
152
228
Max.
Cable Diameter
ø 5.0
ø 6.5
ø 10.0
ø 13.0
7
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
SPLIT FERRITES FOR ROUND CABLE
Features
- Split construction permits easy insertion
of cables already wired and
installed, or cables with connectors.
- Comes with nylon mounting clamp.
- Clamps are made of UL recognized
6/6 nylon (UL94V-2)
Application
For noise problems arising from office
automation equipment or other digital
equipment.
Part No.
TRCN-16-8-13
TRCN-16-8-16
TRCN-20-10-10
TRCN-23-11-14
TRCN-28-16-13
TRCN-28-16-20
TRCN-40-27-15
A
19.4
19.4
25.7
26.8
32.8
32.8
44.6
B
8.2
8.2
10.4
11.4
16.4
16.4
27.4
Unit: mm
C
13.0
16.0
10.0
14.0
13.0
20.0
15.0
D
30.2
30.2
38.2
39.4
45.0
45.0
57.3
F
4.3
4.3
5.1
5.1
5.1
5.1
5.1
Impedance (Ω) 1 turn Impedance (Ω) 2 turn
25MHz 100MHz 25MHz 100MHz
59 93 231 396
64 106 291 504
53 84 203 360
72 112 289 449
56 90 226 374
79 135 325 579
48 84 195 365
Max.
Cable Diameter
ø 8.0 or less
ø 8.0 or less
ø 10.0 or less
ø 11.0 or less
ø 16.0 or less
ø 16.0 or less
ø 27.0 or less
FILTERING
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
8

FILTERING
SPLIT FERRITES FOR ROUND CABLE
patented
Features
- Employ high-performance ferrites (Nickel-Zinc) effective against high
frequency noise
- Ferrite assembly in fully enclosed Nylon 6/6 case, can be installed as a single
add-on component by snapping. (UL 94 V-0)
- Special mounting options include adhesive tape, or screw type through holes
provided.
Application
- Superior suppression of radiation emissions for full compliance with FCC, VDE
and VCCI on interface/ data line round cables of computers, peripheral/terminal
equipment.
A
B
Fig. 1 Fig. 2 Fig. 3 Fig. 4
A
C
C
B
A
E
B
C
B
C
D
D
D
D
A
Part No.
TFC 16813
TFC 16816
TFCM 16-8-13
TFCM 16-8-16
TFC 20-10-10
TFC 23-11-14
TFC 25-15-12
TFCM 41-27-16
TFP 2014-T
TFP 2014-V
Fig.
1
1
2
2
3
3
3
1*
4
4
A
19.8
19.8
19.8
19.8
24.2
27.4
28.2
44
20
20
B
7.6
7.6
7.6
7.6
8.8
10.8
13.6
26.6
13.5
13.5
Unit: mm
C
18.9
21.9
18.9
21.9
13.5
17.5
13.7
19.6
7.2
7.2
D
19.8
19.8
22.3
22.3
27.9
31.0
30.9
48.2
4.8
4.8
E
-
-
-
-
19.9
23.9
20.1
Impedance (Ω) 1 trun Impedance (Ω) 2 trun
25 MHz
57
73
57
73
47
72
41
50
100 MHz
115
139
115
139
92
132
88
100
25 MHz
237
300
237
300
192
301
167
100 MHz
517
597
517
597
410
547
390
Mounting part with adhesive tape
Mounting part for screw ø3.4mm
Applicable cable
diameter (mm)
ø7.2 max
ø7.2 max
ø7.2 max
ø7.2 max
ø8.5 max
ø10.5 max
ø13.0 max
ø26.0 max
9
1* Shape is slightly different, please ask for drawing.
KE KITAGAWA
TFCR series (TFC/TFCM ferrite with
re-use clamp) are available.
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
FLAT CABLE FERRITES
Features
- Employ high-performance ferrites
(Nickel-Zinc) effective against high
frequency noise.
- Special mounting options include
adhesive tape, or screw type through
holes available.
- Designed to help reduce cost and time
to market saving.
- Can be installed in its intended location
before or after product assembly
simply with Mounting part.
Applications
- Superior suppression of radiation
emissions for full compliance with
FCC, VDE and VCCI on Interface/
data line ribbon cables of computers,
peripheral/terminal equipment.
Part No.
SSH-33.5-12
SSH-33.5-20
SSH-40-12
SSH-45-12
A
33.5
33.5
40.0
45.0
B
1.2
1.2
1.2
1.2
Unit: mm
C
6.6
6.6
6.6
6.6
D
12
20
12
12
E
27
27
35
40
Impedance (Ω)
25MHz 100MHz
33 63
52 92
27 61
25 60
Max.
Cable Width (mm)
26
26
34
39
FILTERING
Mounting Parts for SSH type cores + SSC type cores
Part No.:
Material:
FRH-12
PA66 UL94V-0
Part No.:
Material:
FRC-12CP
PA66 UL94V-0
Part No.:
Material:
FRHL-20
PA66 UL94V-2
Part No.
FRH-12
FRHL-20
FRC-12CP
Mounting part for screw (D = > 12mm)
Mounting part for screw (D > = 20mm)
Mounting part
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
10

FILTERING
FLAT CABLE FERRITES
Features
- Employ high-performance ferrites
(Nickel-Zinc) effective against high
frequency noise.
- Designed to help reduce cost and time
to market saving.
- Can be installed in its intended location
before or after product assembly.
Application
- Superior suppression of radiation
emissions for full compliance with
FCC, VDE and VCCI on Interface/
data line ribbon cables of computers,
peripheral/terminal equipment.
No Mounting Parts available for all size
Part No.
FPH-10-6-5
A
10
B
1.8
Unit: mm
C
5.0
D
6.0
E
6.8
Impedance (Ω)
100MHz
20
Max.
Cable Width (mm)
6.5
FLAT CABLE FERRITES
Features
- Employ high-performance ferrites
(Nickel-Zinc) effective against high
frequency noise.
- Designed to help reduce cost and time
to market saving.
- Can be installed in its intended location
before or after product assembly.
C
A
B
F
E
Application
- Superior suppression of radiation
emissions for full compliance with
FCC, VDE and VCCI on Interface data
line ribbon cables of computers peripheral/terminal
equipment.
D
2,0
1,1
1,2
Part No.
FPO-23-8-3
FPO-25-12-3
FPO-31-12-3
FPI-20-12-1,2
A
23.0
25.0
31.0
-
B
19.0
21.0
27.0
-
C
8.0
12.0
12.0
-
Unit: mm
D
2.8
2.8
2.8
-
E
18.5
20.5
26.5
20.5
F
8.0
12.0
12.0
12.0
Impedance (Ω)
25MHz 100MHz
18 42
25 56
24 55
- -
Max.
Cable Width (mm)
18.5
20.5
26.6
-
No Mounting Parts available for all size
11
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
FLAT CABLE FERRITES
Features
- Employ high-performance ferrites
(Nickel-Zinc) effective against high
frequency noise.
- Designed to help reduce cost and time
to market saving.
- Can be installed in its intended locati
on before product assembly.
Applications
- Superior suppression of radiation
emissions for full compliance with
FCC, VDE and VCCI on Interface/ data
line Ribbon/FPC cables of computers,
peripheral/terminal equipment.
Fig.1
B
C
D
B
C
D
FILTERING
Part No.
SSC-21-6.8-8B
SSC-21-6.8-15B
SSC-23.3-3-7
SSC-23.8-6.3-7
SSC-23.8-6.3-12.5
SSC-23.8-6.3-15
SSC-28.5-6.5-8
SSC-28-7.7-14.6
SSC-33.5-8
SSC-33.5-10
SSC-33.5-12
SSC-33.5-10-2
SSC-33.5-20
SSC-38.5-4-12
SSC-38.5-12-25.4
SSC-40-10
SSC-40-12
SSC-45-8
SSC-45-12
SSC-50-12
SSC-58-12
SSC-60-12
Fig.
2
2
2
1
1
1
1
3
1
1
1
1
1
2
2
1
1
1
1
1
1
1
A
21.0±0.5
21.0±0.5
23.3±0.7
23.8±0.7
23.8±0.8
23.8±0.8
28.5±0.7
28.0±0.8
33.5±1.0
33.5±1.0
33.5±1.0
33.5±0.9
33.5±0.9
38.5±1.0
38.53±0.58
40.0±1.0
40.0±1.0
45.2±1.0
45.2±1.0
49.6±1.0
57.6±1.20
60.6±1.1
B
1.3+0.4/-0.1
1.3+0.4/-0.1
0.9±0.2
1.3±0.25
1.1±0.4
1.1±0.4
0.85±0.3
1.4±0.2
1.4±0.4
1.4±0.4
1.4±0.4
2.2±0.3
1.4±0.4
0.8±0.3
1.9±0.38
1.4±0.4
1.4±0.4
1.4±0.4
1.4±0.4
1.4±0.4
1.4±0.4
1.4±0.4
Unit: mm
C
6.8±0.3
6.8±0.3
3.1±0.3
6.3±0.3
6.3±0.4
6.3±0.4
6.5±0.5
7.7±0.3
6.5±0.5
6.5±0.5
6.5±0.5
7.4±0.4
6.5±0.5
4.0±0.2
12.06±0.38
6.5±0.5
6.5±0.5
6.5±0.5
6.5±0.5
6.5±0.5
6.5±0.5
6.5±0.5
D
8.0±0.3
15.0±0.4
7.0±0.3
7.0±0.3
12.5±0.4
15.0±0.4
8.0±0.4
14.6±0.4
8.0±0.4
10.0±0.4
12.0±0.5
10.0±0.5
20.0±0.6
12.0±0.5
25.4±0.76
10.0±0.45
12.0±0.5
8.0±0.3
12.0±0.5
12.0±0.5
12.0±0.5
12.0±0.5
E
15.0±0.5
15.0±0.5
20.0±0.5
18.4±0.5
18.7±0.8
18.7±0.8
23.5±0.5
23.0±0.5
27.0±0.5
27.0±0.5
27.0±0.5
27.0+0.9/-0.6
27.15±0.75
35.0±0.7
26.77±0.76
35.0±0.7
35.0±0.7
40.0±0.8
40.0±0.8
44.0±0.8
52.0±0.8
55.2±1.0
Impedance (Ω)
25MHz 100MHz
32 44
60 75
17 45
27 58
29 83
46 88
28 65
55 115
21 44
26 51
31 58
27 50
58 149
25 68
86 166
23 54
27 60
19 46
26 61
25 64
25 63
35 92
Max. Cable
Width (mm)
14
14
19
18
18
18
22
22
26
26
26
26
26
34
26
34
34
39
39
43
51
54
Mounting Parts Page 10 + 16
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
12

FILTERING
FLAT CABLE FERRITES
13
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
SLIM
CORE
Features
Ultra thin ferrite core for FPC ideal for
space-saving devices
- Reducedd thickness allows an effective
use in a limited space
- Despite the low profile, high performance
is achieved by close contact to
FPC cable
Part No.
FPC-11-3-2
FPC-11-8-2
FPC-18-3-2
FPC-18-8-2
FPC-22-8-2
A
11.0
11.0
18.0
18.0
21.5
B
0.7, +0.2-0.3
0.7, +0.2-0.3
0.7, +0.2-0.3
0.7, +0.2-0.3
0.7, +0.2-0.25
Unit: mm
C
2.3
D
3
8
3
8
8
E
9±0.3
9±0.3
14.5±0.4
14.5±0.4
18±0.5
Impedance
Min(Ω)/100MHz(1turn)
10
20
10
15
20
FILTERING
1000
1000
Impedance (Ω)
100
10
Impedance (Ω)
100
10
1
1
10
100
Frenqueny (MHz)
1000
1
1
10
100
Frenqueny (MHz)
1000
Slim Core
(FPC-18-8-2)
Existing product
FPC-11-8-2
Slim Core
L= 8 mm
FPC-11-3-2
Slim Core
L= 3 mm
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
14

FILTERING
FLAT CABLE FERRITES
Features
- Employ high-performance ferrites
(Nickel-Zinc) effective against high
frequency noise.
- Designed to help reduce cost and time
to market saving.
- Can be installed simply in its intended
location before product assembly.
- Mounting part, FPCK12A, 12B is
available
Applications
- Superior suppression of radiation
emissions for full compliance with
FCC, VDE and VCCI on Interface/
data line FPC cables of computers,
peripheral/terminal equipment.
Part No.
FPC 16-12
FPC-16-20
FPC-25-12
FPC-25-20
FPC-31-12
FPC-46-12
FPC-56-12
FPC-24-12-3
FPC-31-12-3
A
16.0±0.4
16.0±0.4
24.5±0.7
24.5±0.7
31.0±1.0
46.0+1.1/-0.8
56.2±1.1
23.3±0.7
31.0±0.8
B
0.5+0.6/-0.0
0.5+0.6/-0.0
0.5+0.6/-0.0
0.85±0.25
1.0±0.2
0.5+1.0/-0.0
0.5+1.1/-0.0
0.9±0.2
0.9±0.2
Unit: mm
C
5.0+0.0/-0.7
5.0+0.0/-0.7
5.0+0.0/-0.7
5.0+0.0/-0.7
5.0±0.3
5+0.0/-0.8
5+0.3/-1.1
3.1±0.3
3.0±0.2
D
12.0±0.5
20.0±0.6
12.0±0.4
20.0±0.6
12.0±0.5
12.0±0.8
12.0±0.5
12.0±0.5
12.0±0.5
E
11.5±0.4
11.5±0.4
20.0±0.5
20.0±0.5
27.0±0.7
41.5±0.9
52.4±0.9
20.0±0.5
27.0±0.6
Impedance (Ω)
25MHz 100MHz
42 79
71 127
30 65
50 103
26 66
23 65
23 66
20 41
17 42
Max.Cable
width (mm)
10.5
10.5
19.0
19.0
26.0
40.5
51.0
19.0
26.0
15
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
FLAT CABLE FERRITES
Mounting Parts for FPC type cores
Part No.:
Material:
Applicable:
FPCK-12B
PVC
FPC-31-12
FPC-46-12
FPC-56-12
FPC-31-12-3
Part No.
FPCK-12B
FPCK-12A
Part No.:
Material:
Applicable:
FPCK-12A
PVC
FPC-16-12
FPC-25-12
FPC-24-12-3
Applicable
FPC-31-12, FPC-46-12; FPC-56-12; FPC-31-12-3
FPC-16-12; FPC-25-12; FPC-24-12-3
FILTERING
Mounting Parts for SSC type cores
Features
- Plastic clip for SSC-cores
- Material: ABS
- Colour: black
Part No.
FCP-15P
FCP-25P
FCP-34P
FCP-40P
A
34,5
46,5
56,6
64,1
B
0,8
0,8
0,8
0,8
Unit: mm
C
12,0
10,6
10,4
10,4
D
19,0
16,0
16,0
16,0
E
21,6
34,3
43,2
53,3
Applicable
SSC-21-6,8-8 / 21-6,8-15 / 23,8-6,3-7 / 23,8-6,3-15 / 28-7,7-14,6
SSC-33,5-8 / 33,5-10 / 33,5-12 / 33,5-10-2 / 40-10 / 40-12
SSC-45-8 / 45-12 / 50-12
SSC-58-12
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
16

FILTERING
FLAT CABLE FERRITES
Features
- Split construction permits easy insertion
of cables already wired and
installed, or cables with connectors.
- Nylon mounting clamp comes with.
- Split block cores supported with plastic
mounting clamp for flat cables
Applications
- For noise problems arising in
office automation equipment or
other digital equipment.
Part No.
EFC-25S
EFC-40S
EFC-50S
EFC-25N
EFC-40N
EFC-50N
BCN-26
BCN-40
BCN-50
A
44.0
630
76.5
44.0
63.0
76.5
45.0
63.0
76.5
B
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
C
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
Unit: mm
D
28.5
28.5
28.5
28.5
28.5
28.5
28.5
28.5
28.5
E
33.0
52.0
64.5
33.0
52.4
64.5
34.0
52.0
64.5
F
47.0
77.0
79.5
47.0
77.0
79.5
59.0
76.5
90.7
P
33.0
64.5
64.5
–
–
–
–
–
–
25MHz
65
72
62
65
72
62
92
72
63
Impedance (Ω)
100MHz
150
175
185
150
175
185
180
180
185
Applicable cable
flat cable
Less than the
dimension E
17
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
FLAT CABLE FERRITES
Features
- Kitagawa offers a line of bisected flat
cable suppression cores to attenuate
radiated EMI emissions from ribbon
cables.
- Ferrite assembly press-fitted into a
pair of metal clips.
- Metal clips included, except
FP 16,5-2-10.25
Applications
- Internal ribbon cables between PCB
and Data line.
- To suppress radiated EMI emission
from flat cable and ribbon cable.
Part No.
FP 16.5-2-10.25
FP 38-6.35-10
FP 38-6.35-25.4
FP 45-6.35-10
FP 45-6.35-28.5
FP 55.1-6.35-28.5
FP 63.5-6.35-13
FP 63.5-6.35-15
FP 63.5-6.35-28.5
FP 76.2-6.35-28.5
*
*
*
**
**
*
*
**
**
A
16.5±0.25
38.0±1.0
38.0±1.0
45.0±0.75
45.0±0.75
55.1±1.2
63.5±1.3
63.5±1.3
63.5±1.3
76.2±1.5
B
0.6±0.2
0.8±0.2
0.8±0.2
0.8±0.2
0.8±0.2
0.8±0.2
0.8±0.2
0.8±0.2
0.8±0.2
0.8±0.2
Unit: mm
C
2.0±0.2
6.35±0.25
6.35±0.25
6.35±0.25
6.35±0.25
6.35±0.25
6.35±0.25
6.35±0.25
6.35±0.25
6.35±0.25
D
10.25±0.2
10.0±0.4
25.4±0.75
10.0±0.4
28.5±0.7
28.5±0.7
13.0±0.4
15.0±0.4
28.5±0.7
28.5±0.7
E
12.5±0.3
26.6±0.7
26.6±0.7
34.4±0.7
34.4±0.7
43.7±1.0
52.0±1.1
52.0±1.1
52.0±1.1
65.3±1.3
25MHz
29
45
103
41
84
78
45
50
74
72
Impedance (Ω)
100MHz
72
107
173
98
166
179
114
124
155
200
FILTERING
* Metal clips (KE-MC-10 or KE MC-13) are included
** Metal clips (KE-MC-13) are included, however Plastic clip KE-PC-28.5 is also available as option
Metal Clip for FP-core
Features
- Metal clip for FP-core
- Part No. KE-MC-10
- Part No. KE-MC-13
10
Ø 0.7
12.5
11.6
15.7
3.5
15.4 7.6 12.7
KE-MC-10
KE-MC-13
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
18

FILTERING
FLAT CABLE FERRITES
Mounting parts for FP-cores
Features
- Plastic clip for FP- cores
- Nylon 6.6 (UL 94 V-2)
- Colour grey
- Screw mounting
- Part No. KE-PC-28.5
KE-PC-28.5
19
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
ROUND CABLE FERRITES
Features
- Employ high-performance Ferrites
(Nickel-Zinc). Particularly suitable
for high frequency noise.
- Typically wound with two or three
turns of cable. The impedance ratio is
actually proportional to the square
of the turn.
- Can be installed in its intended location
before product assembly.
A
C
B
Applications
- Superior suppression of radiation
emissions for full compliance with
FCC, VDE and VCCI on Interface/ data
line cables of computers,
peripheral/terminal equipment.
Part No.
RI 2.5-4-0.8
RI 3-4-1
RI 3.5-3-1.2
RI 3.5-3.5-1.2
RI 3.5-4-1.2
RI 3.5-5-1.8
RI 3.5-6-1.2
RI 3.5-7-1.2
RI 4-5-2
RI 4-10-2
RI 5-5-2.3
RI 5-11-1.5
RI 5-18-2.2
RI 6-18-3.2
RI 6.35-12.7-3.3
RI 7.5-7.5-2.4
RI 9.3-9.5-4.5
RI 9.5-9.5-5.2
RI 9.5-10-5.8
RI 9.5-10.4-5
RI 9.5-14.5-5
RI 9.5-19-5
RI 10-6-6
RI 10-10-7
RI 10-14-6
RI 11-18-5
RI 11-20-5
RI 11-25-5
RI 11.8-15-7.3
RI 12.0-7.5-7.0
RI 12-15-7
A
2.5±0.15
3.0±0.15
3.5±0.15
3.5±0.15
3.5±0.15
3.5±0.15
3.5±0.15
3.5±0.15
4.0±0.2
4.0±0.2
5.0±0.2
5.0±0.2
5.0±0.2
6.0±0.2
6.35±0.2
7.50±0.3
9.3±0.3
9.5±0.3
9.5±0.3
9.5±0.3
9.5±0.3
9.5±0.3
10.0±0.2
10.0±0.3
10.0±0.3
11.0±0.3
10.5±0.3
11.0±0.3
11.8±0.3
12.0±0.3
12.0±0.3
Unit: mm
B
4.0±0.3
4.0±0.3
3.0±0.2
3.5±0.2
4.0±0.3
5.0±0.3
6.0±0.3
7.0±0.3
5.0±0.3
10.0±0.4
5.0±0.3
11.0±0.4
18.0±0.4
18.0±0.4
12.7±0.4
7.50±0.3
9.5±0.3
9.5±0.3
10.0±0.3
10.4±0.4
14.5±0.4
19.0±0.4
6.0±0.3
10.0±0.4
14.0±0.4
18.5±0.4
20.0±0.4
25.0±0.6
15.0±0.4
7.5±0.3
15.0±0.4
C
0.8±0.15
1.0±0.15
1.2±0.15
1.2±0.15
1.2±0.15
1.8±0.15
1.2±0.15
1.2±0.15
2.0±0.15
2.0±0.15
2.3±0.15
1.5±0.15
2.15±0.15
3.15±0.2
3.3±0.2
2.40±0.15
4.5±0.25
5.2±0.25
5.8±0.2
5.0±0.25
5.0±0.25
5.0±0.25
6.0±0.2
7.0±0.3
6.0±0.3
5.0±0.25
5.5±0.25
5.0±0.25
7.0±0.3
7.0±0.3
7.0±0.3
Impedance (Ω)
25MHz 100MHz
22
58
32
55
24
46
24
43
28
52
26
52
34
61
43
76
20
42
44
67
28
48
71
126
74
114
100
155
61
97
59
107
47
94
46
91
40
79
53
82
62
109
67
125
27
47
32
68
49
86
89
143
74
115
118
187
49
90
32
66
49
90
FILTERING
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
20

FILTERING
ROUND CABLE FERRITES
Part No.
RI 12-16-8.5
RI 12-20-5.6
RI 12-30-5.6
RI 12.3-25.4-4.9
RI 12.5-12.5-8
RI 12.7-12.7-7.9
RI 14-18-6
RI 14.2-15-6.4
RI 14.2-28.5-6.4
RI 14.2-28.5-7
RI 14.2-28.5-8
RI 15-12-10.5
RI 15.3-28-8
RI 15.7-28.6-6.99
RI 15.9-28.6-7.9
RI 16-28-7
RI 16-28-9
RI 16-28.5-8
RI 16-17-9
RI 17.1-25.4-8.8
RI 17.5-28.5-9.5
RI 17.5-28.5-10.7
RI 17.5-35-9.5
RI 18-28-10
RI 19-29-13
RI 25.9-28.6-12.8
RI 26-28-13
RI 28-28-14
RI 28.5-28.6-13.8
A
12.0±0.5
12.0±0.3
12.0±0.3
12.32±0.3
12.5±0.3
12.7±0.3
14.2±0.3
14.2±0.4
14.2±0.4
14.2±0.4
14.2±0.4
15.0±0.4
15.25±0.4
15.65±0.4
15.88±0.4
16.0±0.4
16.0±0.4
16.0±0.4
16.0±0.4
17.07±0.4
17.5±0.4
17.5±0.4
17.5±0.4
18.0±0.5
19.0±0.5
25.91±0.46
26.0±0.6
28.0±0.6
28.5±0.46
Unit: mm
B
16.0±0.5
20.0±0.5
30.0±0.6
25.4±0.6
12.5±0.4
12.7±0.4
18.0±0.4
15.0±0.4
28.5±0.6
28.5±0.6
28.5±0.6
12.0±0.4
28.0±0.6
28.57±0.6
28.57±0.6
28.0±0.6
28.0±0.6
28.5±0.6
17.0±0.4
25.4±0.6
28.5±0.6
28.5±0.6
35.0±0.8
28.0±0.6
29.0±0.6
28.57±0.6
28.0±0.7
28.5±0.6
28.57±0.6
C
8.5±0.25
5.6±0.25
5.6±0.2
4.88±0.2
8.0±0.3
7.9±0.3
6.35±0.25
6.35±0.3
6.35±0.3
7.0±0.3
8.0±0.3
10.5±0.4
8.0±0.3
6.99±0.3
7.87±0.3
7.0±0.3
9.0±0.3
8.0±0.3
9.0±0.3
8.76±0.3
9.5±0.3
10.7±0.4
9.5±0.3
10.0±0.4
13.0±0.4
12.83±0.4
13.0±0.4
14.0±0.4
13.77±0.4
Impedance (Ω)
25MHz 100MHz
43
76
108
154
137
224
145
224
30
74
30
74
97
158
89
150
134
211
106
196
106
162
30
68
91
151
146
206
108
163
126
180
110
199
110
163
70
130
118
182
106
174
98
148
136
288
103
172
77
152
109
179
96
152
133
197
133
197
21
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
ROUND CABLE FERRITES
Features
- Employ high-performance Ferrites
(Nickel-Zinc). Particularly suitable
for high frequency noise.
- Typically wound with two or three turns
of cable. The impedance ratio is
actually proportional to the square
of the turn.
- Can be installed in its intended location
before product assembly.
Applications
- Superior suppression of radiation
emissions for full compliance with
FCC, VDE and VCCI on Interface/ data
line cables of computers,
peripheral/terminal equipment.
A
C
Unit: mm
Impedance (Ω) 1 turn
Part No. A B C 25MHz 100MHz
TR 3.5-1.3-5 3.5±0.15 5.0±0.3 1.3±0.15 29 48
TR 5.65-3.0-9.8 5.65±0.25 9.8±0.4 3.0±0.2 43 77
TR 6-4-10 6.0±0.4 10.0±0.3 4.0±0.2 36 55
TR 7-3-4 7.30±0.25 4.3±0.3 3.3±0.2 24 52
TR 9-5-3 9.0±0.3 3.0±0.2 5.0±0.25 19 44
TR 9-5-8 9.0±0.3 8.0±0.3 5.0±0.25 29 60
TR 9.5-5-5 9.5±0.3 5.0±0.3 5.0±0.25 22 53
TR 10-6-4 10.0±0.3 4.0±0.3 6.0±0.3 22 48
TR 10-5-5 10.0±0.3 5.0±0.3 5.0±0.25 31 59
TR 11-5-9 11.0±0.3 9.0±0.3 5.0±0.25 48 96
TR 12-6-4 12.0±0.3 4.0±0.3 6.0±0.3 24 53
TR 12-7-5.5 12.0±0.3 5.5±0.3 7.0±0.3 26 59
TR 12.5-8-6.3 12.5±0.3 6.35±0.3 8.0±0.3 26 55
TR 12.5-8-12 12.6±0.5 12.0±0.4 8.1±0.4 43 70
TR 13-7-5 13.0±0.4 5.5±0.3 7.0±0.25 34 52
TR 13-7-7 13.0±0.4 7.0±0.4 7.0±0.25 32 64
TR 13-7-12.7 13.0±0.3 12.7±0.4 7.1±0.3 50 86
TR 14.5-10-8 14.5±0.4 8.0±0.3 10.2±0.4 24 62
TR 15.8-7.8-14.2 15.88±0.4 14.27±0.4 7.87±0.3 82 131
TR 16-12-8 16.0±0.4 8.0±0.3 12.0±0.4 20 53
TR 16-9-12 16.0±0.4 12.0±0.4 9.0±0.3 43 86
TR 16-8-13 16.5±0.4 13.0±0.4 8.2±0.3 83 143
TR 16-8-16 16.5±0.4 16.0±0.4 8.2±0.3 97 162
TR 16-10-7 16.0±0.4 7.0±0.3 10.0±0.4 29 67
TR 16-10-10 16.0±0.4 10.0±0.4 10.0±0.4 36 66
TR 17.5-9.5-6.3 17.5±0.4 6.35±0.3 9.5±0.3 32 64
TR 17.5-9.5-12.7 17.5±0.4 12.7±0.4 9.5±0.3 48 77
TR 18-10-6 18.0±0.5 6.0±0.3 10.0±0.4 31 66
TR 18.6-10-14.2 18.67±0.5 14.27±0.4 10.16±0.4 79 139
TR 20-10-5 20.5±0.6 5.0±0.3 10.2±0.4 29 52
TR 20-10-10 20.5±0.6 10.0±0.4 10.2±0.4 59 96
TR 22-13.5-6.3 22.5±0.6 6.3±0.4 13.5±0.4 22 58
B
FILTERING
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
22

FILTERING
ROUND CABLE FERRITES
Unit: mm
Impedance (Ω) 1 turn
Part No. A B C 25MHz 100MHz
TR 22-13.5-8 22.0±0.6 8.0±0.3 13.5±0.4 34 82
TR 23-11-14 23.6±0.6 14.0±0.4 11.4±0.4 73 125
TR 25-15-12 25.0±0.6 12.0±0.4 15.0±0.5 43 86
TR 25.4-12.7-6.3 25.4±0.6 6.35±0.3 12.7±0.4 39 80
TR 28-16-13 28.0±0.6 13.0±0.4 16.0±0.5 58 96
TR 28-16-20 28.0±0.8 20.0±0.5 16.0±0.5 77 145
TR 29-19-7.5 29.0±0.6 7.5±0.3 19.0±0.5 31 80
TR 31-19-8 31.0±0.8 8.0±0.3 19.0±0.5 34 66
TR 31-19-16 31.0±0.8 16.0±0.4 19.0±0.5 58 96
TR 36-25-7 36.0±0.8 7.0±0.3 25.0±0.6 28 76
TR 40-27-15 40.6±1.0 15.0±0.4 27.4±0.6 43 96
TR 61.4-36-12.8 61.4±1.3 12.8±0.4 36.0±0.75 38 91
GRAPHIC DATA OF RI AND TR CORES
23
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
ROUND CABLE FERRITES
FILTERING
RI 11-20-5
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
24

FILTERING
ROUND CABLE FERRITES
25
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
ROUND CABLE FERRITES
FILTERING
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
26

FILTERING
ROUND CABLE FERRITES
27
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
FINEMET CORE (F)
Features
- Toroidal cores employing FINEMET, nanocrystalline soft
magnetic material
- High impedance can be obtained in MHz frequency band
and under.
- FINEMET has very high Curie temperature (570°C) which
results in stable magnetic characteristics at high temperature
range.
- As FINEMET has high saturation magnetic flux denstiy,
three times higher than ferrite cores, superior suppresssion
of spike current is possible with smaller cores.
FILTERING
B
A
C
F3724E
Unit: mm
Part No.
F2515D
F3320E
F3724E
F4424G
F4535G
F6045G
F7555G
A
28.0
35.8
40.0
46.5
49.0
64.0
79.0
B
12.8±0.5
17.3±0.5
21.1±0.5
21.5±0.5
31.0±0.5
41.0±0.7
51.0±0.7
C
16.8
17.5
17.6
22.8
25.0
25.0
25.0
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
28

FILTERING
LOW CUT CORE (TRM)
Features
- High impedance character showed in
low frequency noise
- Reduce damage by load to the cable
due to R shape of ridge coated with
epoxy
epoxy coating
Material
- Mn-Zn Soft Ferrite with Epoxy coating
B
A
C
Unit: mm
Part No.
TRM-16-8-16E-WE
TRM-20-10-10E-WE
TRM-25-15-12E-WE
TRM-47-27-15E-WE
A
17 max
21 max
26 max
48.5 max
B
7.1 min
9.1 min
14.1 min
25.7 min
C
16.9 max
10.9 max
12.9 max
16.3 max
Impedance Frequency
Number of turn wire 2T : 2turns
Number of turn wire 2T : 2turns
Impedance (Ω)
TRM-16-8-16E-WE (Z)
TRM-20-10-10E-WE (Z)
Impedance (Ω)
TRM-25-15-12E-WE (Z)
TRM-47-27-15E-WE (Z)
o.01 0.1 1 10 100 1000
Frenquency ( MHz)
o.01 0.1 1 10 100 1000
Frenquency ( MHz)
Comparative Characteristic
Number of turn wire 1T : 1 turn
Number of turn wire 2T : 2turns
Impedance (Ω)
TRM-16-8-16E-WE 1T
TR-16-8-16(Standard) 1T
Impedance (Ω)
TRM-16-8-16E-WE 2T
TR-16-8-16(Standard) 2T
o.01 0.1 1 10 100 1000
Frenquency ( MHz)
o.01 0.1 1 10 100 1000
Frenquency ( MHz)
29
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
ROUND CABLE FERRITES
Features
- Employ high-performance Ferrites
(Nickel-Zinc). Particularly suitable
for high frequency noise.
- Typically wound with two or three turns
of cable. The impedance ratio is
actually proportional to the square
of the turn.
- Can be installed in its intended location
before product assembly.
A
C
B
D
Applications
- Superior suppression of radiation
emissions for full compliance with
FCC, VDE and VCCI on Interface/ data
line cables of computers,
peripheral/terminal equipment.
E
FILTERING
Part No.
TRE-14-12,5-8
TRE-14-14-8
A
10
10
B
4
4
Unit: mm
C
14
14
D
8
8
E
12,5
14
Impedance (Ω) 1 Turn
25MHz 100MHz
35 66
40 72
Impedance (Ω) 2 Turn
25MHz 100MHz
140 236
158 256
Multi-Aperture wound beads
Typ 1 Typ 2
Part No.
FH8-10.88-5.49-10S
FH6-7.62-5.08-10S
A
10.88
7.62
B
5.49
5.08
C
10.0
10.0
D
5.8
3.8
E
2.54
2.54
F
1.20 max
1.20 max
G
0.4
0.4
25MHz
160
216.3
100MHz
240
241.9
Type
1
2
Rated current
Working temperature
6A
-25°~+85°C
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
30

FILTERING
FERRITE PLATES FOR D-SUB AND CPU
Features
- EMI suppression is achieved by simply
inserting the D sub-plate on the pins of
the connector.
- Space-savings is achieved due to
being integrated in the connector.
- Compared with the bead cores, the
number of parts are reduced.
Applications
- Noise suppression components for
connectors, D sub-type connectors for
CRT, mouse, RS232C interface of
computer, etc.
Part No.
FH9-14.5-7.6-2.8
FH15-22.65-7.6-2.8
FH25-36.4-7.6-2.8
FH37-53.08-7.7-2.8
A
14.5
22.65
36.4
53.08
B
7.6
7.6
7.6
7.7
Unit: mm
C
2.8
2.8
2.8
2.8
D
2.74
2.77
2.77
2.77
E
2.84
2.84
2.84
2.84
øF
1.57
1.57
1.57
1.5
Number
of holes
9
15
25
37
Impedance (Ω)
25MHz 100MHz
35 64
34 65
33 64
34 65
Application
for D sub-connector
for D sub-connector
for D sub-connector
for D sub-connector
CPU-core
Features
- Thermally conductive ferrite plates
designed for EMI absorption for ICs,
CPUs and busdrives running at high
clock speed.
- Reduced thickness (0,8 mm) and
excellent thermal conductivity characteristics
allow the tile to be inserted
between CPU and heart sink providing
EMI shielding without affecting
the heat dissipation process.
- The ferrite tiles are available in standard
(as shown), customized sizes
and are optionally supplied with
thermally-conductive adhesive transfer
tape for convenient fastening.
A
B
C
Part No.
SD-28-28-0,8 *
SD-38-38-2 *
A
28,0
38,0
Unit: mm
B
28,0
38,0
C
0,8
2,0
*Thermal transfer
tape optional (-T)
31
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
WOUND
BEADS
Applications
- The R6H type wide-band chokes are
mainly used in PC boards to filter the
EMI from outside sources.
1
2
3
1.5 Ts
2 Ts
2.5 Ts
4
3 Ts
Part No.
R6H-Type
R6H 6-10-0.85-1.5TS
R6H 6-10-0.85-2TS
R6H 6-10-0.85-2.5TS
R6H 6-10-0.85-3TS
R6H 6-10-0.85-2x1.5TS
A
6.0±0.25
6.0±0.25
6.0±0.25
6.0±0.25
6.0±0.25
5
Unit: mm
B
10.0±0.4
10.0±0.4
10.0±0.4
10.0±0.4
10.0±0.4
øC
0.5
0.5
0.5
0.5
0.5
2 x 1.5 Ts
Impedance (Ω)
25MHz 100MHz
390
510
690
860
340
460
580
680
750
450
Fig.
1
2
3
4
5
FILTERING
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
32

FILTERING
WOUND
BEADS
Features
- Ferrite beads are used to remove high
frequency noise.
- Are supplied taped, suitable for
automatic insertion into p.c. boards.
- Rated current 6A
Applications
- Noise suppression of on-board
components of personal computer,
word processor, facsimile and other
digital equipment.
Rated current
Working temperature
6A
-25°~+85°C
Part No.
RH 3.5-4.7-0.8
RH 3.5-6.0-0.8
RH 3.5-7.5-0.8
RH 3.5-8.0-0.8
RH 3.5-9.0-0.8
A
3.5
3.5
3.5
3.5
3.5
Unit: mm
B
4.7
6.0
7.5
8.0
9.0
øC
0.65
0.65
0.65
0.65
0.65
25MHz
52
57
91
88
97
Impedance (Ω)
100MHz
82
84
111
138
117
33
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
WOUND
BEADS
Part No.
Rated current
Working temperature
RH 3.5-6.0-0.8-DT
RH 3.5-6.0-0.8-AT
6A
-25°C-85°C
RH 3.5-6.0-0.8-DT
A 3.5±0.15
B 6.0±0.3
C 12.7±-0.3
D 5.0±-1.0
E 18.0±-1.0
unit:mm
RH 3.5-6.0-0.8-AT
E
C
D
A
B
FILTERING
A 3.5±0.15
B 6.0±0.3
C 12.7±1.5
D 5.0±0.5
E 16.5±1.0
unit:mm
E
A
C
D
FERRITE DESIGN KIT ESF-10K
Part No.
Quantity
USB-4 2
SFC-5 2
SFC-6 2
SFC-8 2
SFC-10 2
RFC-5 2
RFC-6 2
RFC-8 2
RFC-9 2
RFC-10 2
RFC-13 2
RI-11-25-5 3
RI-14.2-28.5-6.4 3
RI-16-28-7 3
RI-16-28.5-8 3
RI-16-28-9 3
RI-18-28-10 3
RI-26-28-13 3
TR-16-8-13 3
TR-16-8-16 3
TR-20-10-10 3
Part No.
Quantity
TR-25-15-12 3
TR-28-16-20 3
TR-40-27-15 1
TFC-16-8-16 2
TFC-23-11-14 2
TFC-25-15-12 2
TRCN-28-16-13 1
TRCN-28-16-20 1
TRCN-40-27-15 1
SSC-33.5-12 2
SSC-40-12 2
SSC-45-12 2
SSC-50-12 2
SSC-58-12 2
FP-38-6.35-25.4 1
FP-45-6.35-28.5 1
FP-63-6.35-28.5 1
BCN-50 1
R6H-6-10-0.85-2.5Ts 5
Samples of foam gaskets.
ESF-10K
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
34

FILTERING
ABSORBING SHEET MG-Series
Features
MG-0.3A
- Noise absorption sheet composed of
heat-resistant rubber mixed with
highly permeable metal magnetic
material.
- Can be used and shows effectiveness
in a high-temperature environment
up to 150°C; in-vehicle equipment or
periphery of CPU in electronics.
- Neither chlorine(CI)- nor bromine(Br)-
based materials are used.
Characteristics
Thickness (mm)
Operating Temperature (C°)
Volume Resistivity (Ω cm)
Flammability Rating
Material
Feature
Transmission Loss
MG-04
- Sheet thickness: 0.05mm and 0.1mm
- Flexible and easy to install
- With the improved magnetic property,
MG-04 is effective for noise control.
MG-05/MG-06
- High permeabilliy which realizes
excellent performances in noise
supression effect
- Satisfies UL standards.
MG-03A
0.5/1.0
-40 °C ~ +150°C
10 7
UL 94-HB
(equivalent)
Magnetic Metal
Filler+Rubber
Improved Heat
Resistance
- Can easily be cut into any desired
shape.
MG-04 MG-05 MG-05A MG-06 MG-06A
10 7 10 11 10 10
0.05/0.1 0.1 0.25/0.5 0.1 0.25/0.5
-25 °C ~+80 °C
-40°C~+85°C
Ultra Thin, High
Permeability
Reflection Loss
UL94-V-O
Magnetic Metal Filler+Rubber
Super High
Permeability
(μ=50/10MHz)
Super High Permeability
(μ=80/10MHz)
Permeability
Trancemittance (dB) Trancemittance (dB) Trancemittance (dB)
Frenquency ( GHz)
0 1 2 3 4 5
MG-03A(t=1mm)
MG-03A(t=0.5mm)
MG-04(t=0.1mm)
Frenquency ( GHz)
0 1 2 3 4 5
MG-05A(t=0.5mm)
MG-05A(t=0.25mm)
MG-05(t=0.1mm)
Frenquency ( GHz)
0 1 2 3 4 5
MG-06A(t=0.5mm)
MG-06A(t=0.25mm)
MG-06(t=0.1mm)
Reflectivity (dB) Reflectivity (dB) Reflectivity (dB)
0 1 2 3 4 5
MG-03A(t=1mm)
MG-03A(t=0.5mm)
MG-04A(t=0.1mm)
Frenquency ( GHz)
0 1 2 3 4 5
MG-05A(t=0.5mm)
MG-05A(t=0.25mm)
MG-05(t=0.1mm)
Frenquency ( GHz)
0 1 2 3 4 5
MG-06A(t=0.5mm)
MG-06A(t=0.25mm)
MG-06(t=0.1mm)
100
50
0
100
50
MG-03A µ’
MG-03A µ’’
MG-04 µ’
1 10 100 1000
MG-04 µ’’
MG-05A,-05 µ’
MG-05A,-05 µ’’
MG-06A,-06 µ’
0
1 10 100 1000
Measurement method
Measurement method
35
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

FILTERING
ABSORBING SHEET MAB-03
Features
-Highly flexible electromagnetic wave
absorbing sheet, bend-resistant and thin
type
-Suitable for CPU, round cable and chassis
to reduce EMI noise
-Flexible and easy to cut
-Customised die cut is available
Applications
For prevention of radiated EMI noise of
electronic equipment.
For mobile applications such as cellphones,
PDA ect...
Characteristics
Magnetic Material
Thickness (mm)
Operating Temperature (°C)
Volume Resistivity (ohm cm)
Dieelectric Strength (kV)
Flammability Rating
MAB-03
Soft Ferrit
0.4 1.0 2.0 4.0
-25 °C +80 °C
10 12
9(t=0.4mm)
equivalent to UL 94-VO
(for t=4.0mm)
FILTERING
ABSORBING SHEET MAGNEFILM (MFM)
Features
Effective for Leakage Magnetic Flux and
Electromagnetic Wave in Low-frequency
Band
- Effective for leakage magnetic flux and
radiation noise from IC, etc. for which
conventional absorption sheets are not
very effective.
- All around the magnetic foil is laminated
with PET film*
- Stable effectiveness with no rust or crack
coused during use. Easy mounting with
the adhesive backing
Part number MFM-1-0.2-012012T MFM-1-0.2-020020T
Size(mm) 12x12(magnetic foil) 14x14(laminate) 20x20(magnetic) 22x22(laminate)
Thickness (mm)
0.2 (incl. adhesive)
Permeablitiy (10MHz) 65
Adhesive peel strength (N/20mm) 7
Number of Layer Measurement value Attenuation
Without 4.78mT -
1 3.39mT 29%
2 2,14mT 55%
Resistance (Ω)
100
10
MAGNEFILM
Absorption sheet
Cable (no shielding)
MFM (12mm x 12mm)
1
10 100 1000
Frequency(MHz)
*Please keep in mind that MAGNEFILM does not guarantee insulation.
*The data above are central values, not guaranteed performance.
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
36

GROUNDING
FRAME GROUNDING SPACER
The grounding function is combined
with resin-made spacer.
(PATENTED)
Resin made spacer combined with tin
plated phosphor bronze is used for suppression
of EMI and ESD on the PCB.
Specifications:
- Material Resin Part Polyphenylene
ether
Metallic Part
Tin plated
phosphor
bronze
- UL standard (resinpart) UL94V-O
- Contact resistance 10 -2 ~10 -4 Ω
Features
-Pressure devel0ped by plastic and
metal fingers provide contact over p.c.
card for excellent electrical current
passage.
- Stable contact resistance is gained.
- Contact resistance does not vary in
the heat cycle test.
- Even if the screw can not stand at the
center of the PCB, the ground can be
provided as desired.
- Maintenance can be carried out easily.
- The number of parts is reduced.
- The cost is reduced considerably.
Part No.
FGS-3S
FGS-4S
FGS-6S
FGS-8S
FGS-9S
A
9.8
11.4
14.4
17.7
20.0
Unit: mm
B
20.3
21.9
24.9
28.2
30.5
FG EDGE SPACER (FGES-10)
FG edge spacer
A grounding function is added to the
supporting structure as well as
open/close functions of the printed circuit
board. Frame grounding can be
taken from the P.C.board spacer in the
equipment which requires opening/closing
of the P.C.board during
maintenance.
Specifications
-Material:
Resin portion: PPHOX
Metal portion: tin plated phosphor
bronze
-Applicable board thickness:
PC board 1.6mm
Chassis side t 0.8mm-t 2.3mm
Features
-Fire-resistant material is used (equivalent
to UL94V-0)
Article No. FGES-10
PWB side t=1.6±0.15 chassis side t=0.8~2.3
*Remarks:
Two installation holes are placed
on the same axis.
37
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

GROUNDING
GROUNDING
CLAMP/RAIL
Features
- Flexible moulded clamps conform to
the irregularities on cable grounding
contact
- The power cable simultaneously
fastened and grounded.
- Since it is made of resin, it is excellent
in elasticity. Therefore, the cable is not
damaged.
- Light-wight, excellent serviceability
and safety.
- Screw mounting method
Specifications
- Clamp material Nylon 6/6 (UL 94 V-0)
- Electrically conductive material Copper
- Mounting method Screw type (M3+ M4)
The grounding function is combined
with the resin made clamp.
The ground clamp is not only fastens
shielding cable, signal cable of various
electrical equipment and devices, but
also takes a grounding effect. Differing
from existing metallic products, the new
product is made of resin compounds.
Therefore, it has proper elasticity and
can be suitably fitted to the cable, thus
excellent grounding is achieved.
Part No.
FGC-3 M3
FGC-3 M4
FGC-5 M3
FGC-5 M4
FGC-8 M3
FGC-8 M4
A
ø3.5
ø3.5
ø6.0
ø6.0
ø9.6
ø9.6
FG GUIDE RAIL/ FGR-80WSP
Features
- Pressure developed by spherical metal
finger provide contact over P.C. card for
excellence electrical curreent passage.
- Molded guide rail provide rigid guides
to metal finger, P.C. card and chassis
accordingly
- Snap-in rivet mounting method
B
9.5
9.5
10.7
10.7
12.2
12.2
Unit: mm
C
3.2
3.2
4.4
4.4
6.0
6.0
Specifications
Resin portion: Polycarbonate(UL94V-2)
Metal finger portion: Phosphor copper
tin coating
D
18.0
18.0
20.8
20.8
25.2
25.2
Applicable diameter
ø3~ø3.5
ø3~ø3.5
ø5~ø5.5
ø5~ø5.5
ø8~ø8.5
ø8~ø8.5
GROUNDING
A
B
Part No. A B
FGR-80WSP 70 80
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
38

GROUNDING
GROUNDING
CLAMP
Features:
- The NK-NS Series is a highly flexible and lightweight
cable clamp made of PA 6.6 (UL 94-V2)
with a pure silvercoating.
- Round form- no sharp edges to damage cables
- Screw mounting method
H
A
G
H
A
G
H
A
E
G
Inner diameter
Diameter
Outer Center Inner
Part No. Type hole hole hole A B C D E F G H N
NK-2NS 3.0 ––– ––– 3.3 4.3 9.5 ––– ––– 4.8 4.8 1.1 9.5
NK-3NS 4.6 ––– ––– 5.3 4.3 10.3 ––– ––– 4.8 4.8 1.1 9.5
NK-4NS 5.6 ––– ––– 6.8 4.3 11.1 ––– ––– 4.8 4.8 1.1 9.5
NK-5NS 7.4 ––– ––– 8.4 4.3 11.9 ––– ––– 4.8 4.8 1.1 9.5
NK-6NS 10.0 ––– ––– 10.6 4.3 12.7 ––– ––– 4.8 6.3 1.1 9.5
NK-7NS 10.7 ––– ––– 12.2 4.3 13.5 ––– ––– 4.8 6.3 1.1 9.5
NK-8NS 11.9 ––– ––– 13.2 4.3 14.3 ––– ––– 4.8 6.3 1.1 9.5
NK-9NS 13.5 ––– ––– 15.2 4.3 15.1 ––– ––– 4.8 6.3 1.1 9.5
NK-10NS 14.0 ––– ––– 16.0 4.3 15.9 ––– ––– 4.8 6.3 1.1 9.5
NK-11NS 16.8 ––– ––– 19.0 5.1 17.5 ––– ––– 6.3 7.9 1.8 12.7
NK-12NS 17.8 ––– ––– 19.8 5.1 18.2 ––– ––– 6.3 7.9 1.8 12.7
NK-13NS 20.8 ––– ––– 22.1 5.1 19.0 ––– ––– 6.3 7.9 1.8 12.7
NK-14NS 21.3 ––– 18.5 22.9 5.1 19.8 11.9 ––– 6.3 7.9 1.8 12.7
NK-16NS B 24.4 ––– 22.3 26.9 5.1 21.4 13.5 ––– 6.3 7.9 1.8 12.7
NK-18NS 26.7 ––– 24.1 29.2 5.1 23.0 15.1 ––– 6.3 7.9 1.8 12.7
NK-24NS 37.3 35.0 31.2 39.4 5.1 27.8 19.8 11.9 6.3 9.5 1.8 12.7
NK-32NS C 51.0 46.2 43.7 52.1 5.1 34.1 24.6 13.5 6.3 9.5 1.8 12.7
MOQ 500pcs
HIGH POINT CONTACT (HPC)
Features:
- Special profile allows the contact
inter-distance to vary from 10 to 20
mm.
- Space saving as there is no change
in spring length when compressed.
- Easy to assemble by screw or adhesive
tape.
Matereial:
- stainless (SUS304/t = 0.15 mm)
Installation:
- Screw M3 / Addhesive tape
Part No.
HPC-10-20T
HPC-10-20
Specification
with dahesive tape
without adhesive tape
22
25
10
39
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

GROUNDING
GROUNDING
MESH/STRAPS
Features
- Excellent impedance characteristics at
high frequencies.
- Thin and flexible aids installation.
- Other Length up to 400mm are
available. Please ask our sales department.
Specifications
- Wire mesh diameter ø0.12 mm
- Wire mesh material tin plated
copper
- Insulation tube resin polyolefine
material
- Connection terminals R2-3
(for M3)
Part No.
FGM-50
FGM-100
FGM-150
FGM-200
A
50
100
150
200
Unit: mm
B
8
8
8
8
FGC FEHLT
C
2
2
2
2
Features
- Low Impedance ground paths at RF
frequencies.
- Lightweight and very flexible. The
lightweight eases strain relief requirements,
while the flexibility eases
strap routing during assembly.
Specifications
Metal part:
Insulating part:
Screw type:
copper sheet
(100μM)
PVC
(noncombustible)
M3, M4 (Screw not
included)
GROUNDING
Part No.
FGST-50-10-M3C
FGST-100-10-M3C
FGST-150-10-M3C
FGST-50-10-M4C
FGST-100-10-M4C
FGST-150-10-M4C
A
40
90
140
40
90
140
Unit: mm
B
50
100
150
50
100
150
C
3.1
3.1
3.1
4.1
4.1
4.1
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
40

GROUNDING
ON-BOARD
CONTACTS
Features
- Contact components enable automatic mounting.
Contact components enhance grounding effect
around PCBs (printed circuit boards).
- Supplied with the enboss tape for autoinsertion
assembly.
- Height 1.0mm- 7.0 mm are available.
- Improved spring form.
OG-301012
OG-320816
OG-321022
OG-321610G
OG-340815P
A
B
3.0
1.0
3.2
0.8
3.2
1.0
3.2
1.6
3.4
0.8
C
1.2
1.6
2.2
1
1.5
Metal Thickness
Material
Surface treatment
Packing Quantity
0.08
Phosphor Bronze
Surface Partly Alu
plating on the
underplating Ni
8000
0.12
Phosphor Bronze
Partly Au plating on
the underplating
by Ni
8000
0.12
Phosphor Bronze
Partly Au plating on
the underplating
by Ni
7000
0.08
Stainless steel
Partly Au plating on
the underplating
by Nii
3000
0.08
BeCu
Partly Au plating on
the underplating
by Ni
8000
Dimensions
B
B
B
A
C
C
A
B
C
A
B
C
A
C
A
More technical data upon request
A
B
OG-362550
3.6
2.5
OG-363040
OG-363050
3.6
3
OG-450818
4.5
0.8
OG-453060
OG-453070
4.5
3.0
OG-502620R
5
2.6
C
5.0
4.0 (OG-363040)
5.0 (OG-363050)
1.8
6.0 (OG-453060)
7.0 (OG-453070)
2
Metal Thickness
0.15
0.1
0.12
0.22
0.08
Material
Surface treatment
Phosphor Bronze
Sn reflow plating
BeCu
Ni plating Partly Sn
plating on the
underplating by Ni
BeCu
Partly Au plating on
the underplating
by Ni
Phosphor Bronze
Sn reflow plating
Stainless steel
Partly Au plating on
the underplating
by Ni
Packing Quantity
1000
1000
8000
1500
2000
Dimensions
B
B
C
C
A
C
A
B
C
C
A
A
B
A
B
41
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

GROUNDING
ON-BOARD
CONTACTS
OG-503040
OG-542925
OG-603060
OG-603070
OG-865028
A
B
5
3
5.4
2.9
6.0
3.0
8.6
5.0
C
4
2.5
6.0 (OG-603060)
7.0 (OG-603070)
2.8
Metal Thickness
0.1
0.12
0.12 (OG-603060)
0.08 (OG-603070)
0.08
Material
Surface treatment
Packing Quantity
BeCu
Sn plating
1000
Phosphor Bronze
Partly Au plating on
the underplating
by Ni
5000
Phosphor Bronze
Sn plating
850 (OG-603060)
750 (OG-603070)
Phosphor Bronze
Sn plating
3000
Dimensions
B
C
B
C
C
A
B
A
C
A
A
B
ON BOARD CLAMP/ON BOARD CLIP / ON BOARD SIDE CONTACT
A
B
C
Metal Thickness
OGC-331610
3.3
1.6
1.05
0.15
OGC-311510U
3.1
1.5
1.02
0.12
OGCP-650813*
6.7
0.8
1.28
0.15
OGCP-1182435
11.8
2.4
3.5
0.2
OGSC-756030
7.5
6.0
3
0.12
GROUNDING
Material
Phosphor Bronze
Phosphor Bronze
Titanium copper
Phosphor Bronze
Phosphor Bronze
Surface treatment
Sn plating
Sn plating
Sn plating
Sn reflow plating
on Cu plating
Sn plating
Packing Quantity
3000
3000
8000
3000
2000
Dimensions
A
B
C
C
B
A
A
C
A
C
A
B
B
C
B
*with Gold plating available (with suffix "G")
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
42

GROUNDING
ON-BOARD SOFT CONTACT
Features
- SMD Grounding Components with soft contact (Silicon
with Ag based filler)
- Contact components enable automatic mounting
- Sonftness of conductive elastomer enables superior contact
- Lower impedance at higher frequency range because of
wide surface of contact
- Silicon material causes no damage to plated surface or
conductive paint
Height 5,5mm-7,5mm are available
Resisitance (Ω)
Charactaristic of Compression Resistance
OGSS-483055
0.05
25
Resisitance
Compression Force
0.04
0.03
0.02
0.01
0
20
15
10
5
0
4.5 4.4 4.2 4 3.8 3.6 3.4 3.2
Gap
Compression Force (N)
Impedance (Ω)
Comparison test of Impedance
5
OG-363050
4
OG-483055
3
2
1
0 1 10 100 1000
Frequency
(dimension in mm)
A
B
C
C
(after Compression)
D
Material
Thickness
Material
Surface
treatment
Packing
Quantity
OGSS-483055
5.5
3.2-4.5
2000
OGSS-483065
4.5
4.8
6.5
4.2-5.5
3.0
0.15
Phosphor Bronze
Sn reflow plating on Cu plating
1800
OGSS-483075
7.5
5.2-6.5
1500
Dimensions
C
A
B
D
43
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

2
GROUNDING
ON-BOARD LUG TERMINAL
Features
- To be able to avoid the solder flux
problem
- FG terminal to be soldered on the PCB
- Supplied with enboss tape for automatic
chip mounter machine
- Diameter of screw bolt shall be
2.6mm and 3.0 mm
A
B
C
Metal Thickness
Material
Surface treatment
Packing Quantity
OG-R26-SN OG-R30-SN
10.7
12.7
6
8
3
4
0.3
0.3
Tough Pitch copper
Pb-Sn Plating on Cu plating
2000
2000
OG-RM26
6.85
4.7
3
0.4
Brass
8000
OG-RM30 OG-RM30HF
10,4
8
7.6
7.6
4
4
0.3
0,3
Tough Pitch copper
Sn plating on Ni plating
3000
3000
C
C
C
C
C
Dimensions
A
A
A
A
A
B
B
B
B
B
ON-BOARD
PLATE
Metal Thickness
Material
Surface treatment
OGP-3216
0.1
Brass
Au/Ni plating
OGP-4520
0.15
Brass
Sn plating on the
underplaing by Cu
0.3
(0.2)
(2.4)
3.2
1.5
1.6
0.2 ± 0.15
0.05
0.15 ± 0.05
4.5
2
GROUNDING
Packing Quantity
4000
3000
OGP-3216
OGP-4520
ON-BOARD CONTACT ENGINEERING KIT OG-K01/OG-K02T.
On-board contact engineering Kit OG-K01.
Various on-board contacts in a compact case.
OG-K01 (OG series)
OG-K02T (TOG series)
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
44

GROUNDING
ON-BOARD
CONTACTS
Features
- Contact components enable automatic mounting.
Contact components enhance grounding effect
around PCBs (printed circuit boards).
- Supplied with the enboss tape for autoinsertion
assembly.
- Improved spring form.
Dimension in mm
Height: 2.0 - 6.2 mm are available
Material: 0.08 mm Beryllium Copper
Gold plating on Nickel underplating
Nickel (μm) Au (μm)
3.05 0.03
Description
W
T
Original Height H
Final height(mm)- Min
(after compression) Max
Compression Ratio(final/original)
TOG-20-30-25
2.00
3.00
2.50
1.70
2.25
68%~90%
TOG-20-30-40
2.00
3.00
4.00
2.30
3.80
58%~95%
TOG-20-40-20
2.00
4.00
2.00
1.30
1.70
65%~85%
W
W
W
Dimensions
H
H
H
T
T
T
Description
W
T
Original Height H
Final height(mm)- Min
after compression Max
Compression Ratio(final/original)
TOG-20-45-45
2.00
4.50
4.50
3.15
4.00
70%~89%
TOG-20-47-57
2.00
4.70
5.70
2.40
5.10
42%~89%
TOG-20-70-62
2.00
7.00
6.20
3.50
5.50
56%~89%
TOG-25-30-40
2.50
3.00
4.00
2.50
3.60
63%~90%
TOG-20-40-21
2.50
4.00
2.10
1.60
2.00
76%~95%
W
W
W
W
W
Dimensions
H
H
H
H
H
T
T
T
T
T
Description
W
T
Original Height H
Final height(mm)- Min
after compression Max
Compression Ratio(final/original)
TOG-25-40-41
2.50
4.00
4.10
3.80
2.60
63%~93%
TOG-25-40-50
2.50
4.00
5.00
2.00
4.75
40%~95%
TOG-25-40-55
2.50
4.00
5.50
2.80
5.25
51%~95%
TOG-25-45-48
2.50
4.50
4.80
3.00
4.30
63%~90%
TOG-40-40-51
4.00
4.00
5.10
3.10
4.60
61%~90%
W
W
W
W
W
Dimensions
H
H
H
H
H
T
T
T
T
T
45
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

GROUNDING
ON-BOARD
CONTACTS
Features
- Contact components enable automatic
mounting.
Contact components enhance
grounding effect
around PCBs (printed circuit
boards).
- Supplied with the enboss tape for
autoinsertion assembly.
- Improved spring form.
- All products are gold plating on
nickel underplating
Height: 2.15 - 6.2 mm are available
Material: BerylliumCopper
Dimension in mm
Description
W
T
H
Material Thickness
Packing Quantity
FOG-206030
2.00
6.00
3.00
0.08
4000
FOG-203230
2.00
3.20
3.00
0.08
2500
FOG-224021
2.20
4.00
2.15
0.08
3000
FOG-256248
2.50
6.20
4.80
0.10
200
W
W
W
Dimensions
H
H
H
H
T
W
T
T
T
Description
W
T
H
Material Thickness
Packing Quantity
FOG-256866
2.50
6.88
5.32
0.15
1000
FOG-254945
2.50
4.95
4.50
0.15
1500
FOG-255036
2.50
5.00
3.60
0.10
1500
FOG-254143
2.50
4.10
4.29
0.10
1500
Dimensions
H
H
W
H
H
Description
W
T
H
Material Thickness
Packing Quantity
T
FOG-254536
2.50
4.50
3.60
0.10
2000
W
T
FOG-203040
2.00
3.00
4.00
0.10
1500
T
FOG-173936
1.70
3.95
3.60
0.10
1500
W
T
FOG-257062
2.50
7.00
6.20
0.15
1000
W
GROUNDING
Dimensions
T
H
W
W
H
W
H
W
T
H
T
T
Description
W
T
H
Material Thickness
Packing Quantity
FOG-254757
2.50
4.70
5.70
0.10
850
FOG-255542
2.50
5.50
4.20
0.15
1000
FOG-254338
2.50
4.31
3.85
0.10
1500
FOG-204838
2.02
4.81
3.86
0.08
1500
W
Dimensions
W
H
H
H
H
T
T
T
W
T
W
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
46

GROUNDING
CONDUCTIVE
TAPE
Easy application same uses as a transparent
tape. High shielding effectiveness due to highly
conductive adhesive tape. Easy cutout or configuration
for optimum shielding effectiveness.
width (mm)
DIMENSION
Length(m)
10
15
20 33
25
50
Other width available upon request
SUPPORTING BASE
Soft – Copper
Soft – Aluminium
Soft – Copper
doublesided tin-coated
CCT-10-C CCT-10-A CCT-10-CS
CCT-15-C CCT-15-A CCT-15-CS
CCT-20-C CCT-20-A CCT-20-CS
CCT-25-C CCT-25-A CCT-25-CS
CCT-50-C CCT-50-A CCT-50-CS
With masking tape available
Technical Data
Colour original original original
Thickness without adhesive (mm) 0,035 ± 10% 0,050 ± 10% 0,037 ± 10%
Thickness with adhesive (mm) 0,055-0,065 0,080 ± 10% 0,072 ± 10%
Kind of adhesive
Acrylic resin, electrical conductive
Eletrical conductivity

GROUNDING
TECHNICAL ADHESIVE TAPES FOR SPECIAL APPLICATIONS
Features
- Polyamid-fleece, metal-coated, with high-quality acrylic
adhesive and very good conductivity.
- For usage as screening material (EMC). Also available with a
covering on the fleece-side. The covering is used as a protection
in the painting process of casings (e.g. power-switch
boxes). After drying or burn in of powder-base painting
(max. 210°C, 1/2 hour) it can be removed from the fleece. For
electrical contact of EMC-gaskets with the casing. No slitaerial
can appear.
- conductivity of the fleece:

GROUNDING
CONDUCTIVE FABRIC TAPE - CNT
Features
Conductive adhesive is made of mixed metal pastes with the normal adhesive to
improve conductivity. This material has very good effectiveness for EMI shielding
and electric to objects needed conductivity.
Non-dioxin type flame retardent.
Part No. Width(mm) Roll (m)
CNT-10H 10
50
CNT-20H 20
50
CNT-25H 25
50
CNT-50H 50
50
Material
Backing
Adhesive
Conductive Filler
Liner
CF-235 (Rip-Stop)
Conductive Acrylic Adhesive
Nickel Powder
Release Liner Paper
Ni+Cu+Ni
Non-Dioxin type FR
Standard sizes & Appearance
Thickness
Color
Overall
Backing
Adhesive
Release Liner
mm
mm
mm
mm
-
0.14± 0.02
0.1
0.04
0.076
Gray
Dial gage
Dial gage
Dial gage
Dial gage
General Properties
Adhesion
Ball tack
Shielding Effectiveness
Holding Power
Surface Resistance
Electric Resistance
gf/25mm
No.
dB
mm
Ω/cm 2
Ω/cm 2 1000+100
7~9
60~70
No Creep
Less than 0.05
Less than 0.03
JIS Z 0237
JIS Z 0237
ASTM D 4935-89
JIS Z 0237
ISL 2000A
HIOKI 3540
Structure
Conductive Fabric
Conductive Acrylic
Adhesive(non-Dioxin)
Release Liner
49
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

SHIELDING
FABRIC FOAM OVER GASKET
Features
Broad range of the most advanced and sophisticated EMI
shielding gaskets Effectiveness from 30Mhz to 1Ghz. The Core
of polyurethane foam(which is approved as UL94 HF-1) in
high resiliency provides high elasticity and very good self stability
easy to process and cut. Gold gasket and Black gaskets
are available.
Conductive fabric
Physical Property
Material
PET 100%
Physical Property
Tensil strength
(kgf)
warp
49.7
Plating
Method
Ni+Cu+Ni 73±3 0.1±0.015 128.8 113.4
weft
38.8
warp
23.6
Weight
(g/m 2 )
Extension
(%)
weft
27.9
Thickness Fabric Count(thread/inch)
(mm) wrap weft
Surface
Resistance (Ω/cm 2 )
MIN
0.03
Shielding
Effetiveness(dB)
MAX 30MHz-1GHz
0.05 60 70
Material/Form
PET 100%
Product Cross
Section
Type of Gasket EMI GASKET EMI GOLD GASKET EMI BLACK GASKET
Symbol of fabric for Part.no. VNN GLD BLK
Raw Material of Fabric PET 100% PET 100% PET 100%
Plating Ni+Cu+Ni Ni+Cu+Ni+Au Ni+Cu+Ni+Carbon
Composition Rip stop Taffeta Rip stop
Foam Core (Polturethan eFoam)
UL 94 HF-1
Shielding effectiveness (dB) 80-100 80-100 80-100
Surface resistance (Ω/cm 2 ) less than 0.05 less than 0.03 less than 0.05
Electric resistance (Ω/cm 2 ) less than 0.03 less than 0.02 less than 0.03
Compression Set 30% 30% 30%
Compression load deflection 2 kg 2 kg 2 kg
Flame retardant UL 94-VO N/A N/A
Service Temp. up to 100°C up to 100°C up to 100°C
Advantage Lower Cost price Better Conductivity water-resistant
No Finger Print
Poly Urethane Foam
Material
SFHL - 13
Polyuretthane
Foam
Classification
Density
kg/m 3
25lLD
Ball
Rebound
Tensile
Strength
Tear
Strength
Unit kg/m kg/314cm 2 % kg/cm 2 kg/cm % % m/min
Typical 45±3 30~35 50min Min.1.5 Min. 0.4 Max. 6 Min. 120 pass
values 45.70 34.38 52 1.869 0.877 4.53 122.43 pass
Pressure Sensitive Adhesive(P.S.A)
Specification
Part No
Thickness
Recommended
Operating Temperature
Colour
Standard adhesive (VTM-0)
Nitto 5011N
0.16mm
-20°C to 120°C
white
KE KITAGAWA
Compreession
fatigue set
(70m,22hr,50%)
Conductive Adhesive
CMFT-130-D
0.12mm
-20°C to 120°C
Elongation
Flame
retardant
Reference JIS-K-6401 JIS-K-6401 JIS-K-6401 JIS-K-6401 JIS-K-6401 JIS-K-6401 JIS-K-6401 FMVSS-302
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
gray
50
SHIELDING

SHIELDING
FABRIC OVER FOAM GASKET
Rectangular PROFILE
H
PROFILE NO
KE-FG-R01
KE-FG-R02
KE-FG-R03
KE-FG-R04
KE-FG-R05
KE-FG-R06
KE-FG-R07
KE-FG-R08
KE-FG-R09
KE-FG-R10
KE-FG-R11
KE-FG-R12
KE-FG-R13
KE-FG-R14
KE-FG-R15
KE-FG-R16
KE-FG-R17
KE-FG-R18
KE-FG-R19
KE-FG-R20
KE-FG-R21
KE-FG-R22
KE-FG-R23
KE-FG-R24
KE-FG-R25
KE-FG-R26
KE-FG-R27
KE-FG-R28
KE-FG-R29
KE-FG-R30
KE-FG-R31
KE-FG-R32
KE-FG-R33
KE-FG-R34
KE-FG-R35
KE-FG-R36
KE-FG-R37
KE-FG-R38
KE-FG-R39
KE-FG-R40
KE-FG-R41
W
SIZE (WxH)
3.0 X 2.0
4.0 X 2.0
4.0 X 3.0
4.0 X 4.0
4.8 X 3.2
5.0 X 2.0
5.0 X 3.0
5.0 X 4.0
5.0 X 5.0
5.0 X 6.0
5.0 X 7.0
5.5 X 5.5
6.0 X 2.0
6.0 X 3.0
6.0 X 4.0
6.0 X 5.0
6.0 X 6.0
6.0 X 8.0
6.4 X 3.2
6.4 X 4.8
6.4 X 6.4
6.5 X 4.0
6.5 X 6.5
7.0 X 2.0
7.0 X 3.0
7.0 X 4.0
7.0 X 7.0
7.0 X 8.0
8.0 X 2.0
8.0 X 3.0
8.0 X 4.0
8.0 X 5.0
8.0 X 6.0
8.0 X 8.0
8.0 X 10
8.0 X 12
8.0 X 15
9.0 X 2.0
9.0 X 3.0
9.0 X 4.0
9.0 X 5.0
PROFILE NO SIZE (WxH)
KE-FG-R42 9.0 X 6.0
KE-FG-R43 9.5 X 3.2
KE-FG-R44 9.5 X 6.4
KE-FG-R45 9.5 X 9.5
KE-FG-R46 10 X 2.0
KE-FG-R47 10 X 3.0
KE-FG-R48 10 X 4.0
KE-FG-R49 10 X 4.5
KE-FG-R50 10 X 5.0
KE-FG-R51 10 X 5.5
KE-FG-R52 10 X 6.0
KE-FG-R53 10 X 7.0
KE-FG-R54 10 X 8.0
KE-FG-R55 10 X 10
KE-FG-R56 10 X 12
KE-FG-R57 10 X 13
KE-FG-R58 10 X 14
KE-FG-R59 10 X 15
KE-FG-R60 10 X 17
KE-FG-R61 10 X 18
KE-FG-R62 10 X 20
KE-FG-R63
12 X 2
KE-FG-R64
12 X 3
KE-FG-R65
12 X 4
KE-FG-R66
12 X 6
KE-FG-R67
12 X 8
KE-FG-R68 12 X 10
KE-FG-R69 12 X 12
KE-FG-R70
13 X 7
KE-FG-R71
13 X 8
KE-FG-R72
13 X 9
KE-FG-R73 13 X 10
KE-FG-R74 13 X 12
KE-FG-R75 13 X 13
KE-FG-R76
15 X 2
KE-FG-R77
15 X 4
KE-FG-R78
15 X 5
KE-FG-R79
15 X 6
KE-FG-R80 15 X 10
KE-FG-R81 15 X 15
KE-FG-R82 16 X 10
KE-FG-R83 17 X 10
KE-FG-R84 17 X 15
KE-FG-R85 17 X 17
KE-FG-R86 17 X 21
KE-FG-R87 17 X 25
KE-FG-R88
18 X 3
KE-FG-R89 18 X 10
51
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

SHIELDING
FABRIC OVER FOAM GASKET
PROFILE NO
KE-FG-R90
KE-FG-R91
KE-FG-R92
KE-FG-R93
KE-FG-R94
KE-FG-R95
KE-FG-R96
KE-FG-R97
KE-FG-R98
KE-FG-R99
KE-FG-R100
KE-FG-R101
KE-FG-R102
KE-FG-R103
KE-FG-R104
KE-FG-R105
KE-FG-R106
KE-FG-R107
KE-FG-R108
KE-FG-R133
KE-FG-R175
KE-FG-R176
KE-FG-R177
KE-FG-R179
KE-FG-R240
KE-FG-R250
KE-FG-R260
KE-FG-R265
KE-FG-R270
SIZE (WxH)
18 X 15
20 X 6
20 X 7
20 X 9
20 X 10
20 X 12
20 X 14
20 X 16
20 X 20
25 X 10
25 X 12
25 X 25
26 X 12
26 X 17
30 X 4.5
30 X 10
30 X 30
33 X 6
44 X 20
3.0 X 3.0
12.7 X 6.4
12.7 X 3.2
12.7 X 12.7
12.7 X 9.5
KE-FG-R186 18 X 6
KE-FG-R194 13 X 10.5
KE-FG-R200 11.5 X 10.5
KE-FG-R205 12.7 X 2
KE-FG-R210 12.7 X 3.7
KE-FG-R220 15 X 7.5
KE-FG-R230 25.4 X 9.5
13.5 X 10
25 X 20
10 X 2.5
4.8 X 3.3
2.3 X 2.3
13 X 4
KE-FG-R280
KE-FG-R290 2 X 2
KE-FG-R300
KE-FG-R310
KE-FG-R320
KE-FG-R330
KE-FG-R340
KE-FG-R350
20 X 35
19 X 25
6 X 7
10.5 X 11.5
20 X 4
20 X 8
H
FLAT PROFILE
PROFILE NO
KE-FG-F01
KE-FG-F02
KE-FG-F03
KE-FG-F04
KE-FG-F05
KE-FG-F06
KE-FG-F07
KE-FG-F08
KE-FG-F09
KE-FG-F10
KE-FG-F11
KE-FG-F12
KE-FG-F13
KE-FG-F14
KE-FG-F15
KE-FG-F16
KE-FG-F17
KE-FG-F18
KE-FG-F19
KE-FG-F20
KE-FG-F21
KE-FG-F22
KE-FG-F23
KE-FG-F24
KE-FG-F25
KE-FG-F26
KE-FG-F27
KE-FG-F28
KE-FG-F29
KE-FG-F30
KE-FG-F31
KE-FG-F32
KE-FG-F33
KE-FG-F34
KE-FG-F35
KE-FG-F36
KE-FG-F37
KE-FG-F38
KE-FG-F92
KE-FG-F110
KE-FG-F120
KE-FG-F130
W
SIZE (WxH)
2.0 X 1.2
3.0 X 0.3
3.0 X 1.0
3.0 X 1.2
3.0 X 1.5
4.0 X 1.0
4.0 X 1.2
4.0 X 1.5
5.0 X 0.5
5.0 X 1.0
5.0 x 1.2
5.0 x 1.5
5.0 x 1.8
6.0 x 1.0
6.0 x 1.2
6.0 x 1.5
7.0 x 1.0
7.0 x 1.2
7.0 x 1.5
7.0 x 1.8
8.0 x 1.0
8.0 x 1.2
8.0 x 1.5
9.0 X 0.5
9.0 X 1.0
9.0 X 1.5
9.0 X 1.8
10 X 0.5
10 X 1.0
10 X 1.2
10 X 1.5
12 X 1.0
12 X 1.5
13 X 1.0
13 X 1.5
14 X 1.5
15 X 0.8
15 X 1.0
9.7 x 1.5
6.0 x 1.25
13 x 2.0
4.0 x 0.5
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
52
SHIELDING

SHIELDING
FABRIC OVER FOAM GASKET
D-PROFILE
53
H
PROFILE NO
KE-FG-D01
KE-FG-D02
KE-FG-D03
KE-FG-D04
KE-FG-D05
KE-FG-D06
KE-FG-D07
KE-FG-D08
KE-FG-D09
KE-FG-D10
KE-FG-D11
KE-FG-D12
KE-FG-D13
KE-FG-D14
KE-FG-D15
KE-FG-D16
KE-FG-D17
KE-FG-D18
KE-FG-D19
KE-FG-D20
KE-FG-D21
KE-FG-D22
KE-FG-D23
KE-FG-D24
KE-FG-D25
KE-FG-D26
KE-FG-D27
KE-FG-D28
KE-FG-D29
KE-FG-D30
KE-FG-D31
KE-FG-D32
KE-FG-D33
KE-FG-D34
KE-FG-D35
KE-FG-D36
KE-FG-D37
KE-FG-D38
KE-FG-D39
KE-FG-D40
W
SIZE (WxH)
2.3 X 2.3
2.3 X 3.2
3.0 X 2.0
3.0 x 3.0
3.0 x 3.5
3.8 x 1.5
3.8 X 3.0
4.0 X 4.0
5.0 X 2.0
5.0 X 5.0
6.0 X 2.0
6.0 X 4.0
6.0 X 4.5
6.0 X 5.0
6.0 X 5.5
6.0 X 6.0
6.4 X 3.6
6.5 X 3.4
6.5 X 5.0
6.5 X 6.0
7.0 X 5.0
8.0 X 5.0
8.0 X 8.0
8.0 X 10
9.0 X 3.0
9.0 X 3.2
9.0 X 6.0
9.5 X 3.2
9.5 X 6.0
10 X 2.0
10 X 3.0
10 X 4.0
10 X 5.0
10 X 6.0
10 X 7
10 X 10
10 X 12
11 X 4.5
12 X 1
12.7 X 9.5
KE-FG-D41 13 X 5
KE KITAGAWA
PROFILE NO
KE-FG-D42
KE-FG-D43
KE-FG-D44
KE-FG-D45
KE-FG-D46
KE-FG-D110
KE-FG-D120
KE-FG-D130
KE-FG-D140
KE-FG-D150
C-FOLD PROFILE
SIZE (WxH)
15 X 5.5
15 X 6
18 X 14
18 X 20
18 X 23
9.5 X 6.4
7.6 X 4.8
3.8 X 2.3
17 X 8
4.0 X 2.0
KE-FG-D160 6.4 X 3.2
KE-FG-D200 2 X 2
KE-FG-D210 10 X 2.4
KE-FG-D230 6 X 7
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
H
W
PROFILE NO SIZE (WxH)
KE-FG-C01 8.0 x 8.0
KE-FG-C03 10.7 x 8.5
KE-FG-C04 10.7 x 9.8
KE-FG-C10 14.7 x 17.1
KE-FG-C20 6.35 x 6.35
KE-FG-C21 5.9 x 6.4
KE-FG-C23 7.1 x 6.4

SHIELDING
FABRIC OVER FOAM GASKET
WIDE PROFILE
(I.O. GASKET)
W
H
P-PROFILE
H
↔
W
PROFILE NO
KE-FG-W01
KE-FG-W02
KE-FG-W03
KE-FG-W04
KE-FG-W05
KE-FG-W06
KE-FG-W07
KE-FG-W08
KE-FG-W09
KE-FG-W10
KE-FG-W11
KE-FG-W12
KE-FG-W13
KE-FG-W14
KE-FG-W15
KE-FG-W16
KE-FG-W17
KE-FG-W18
KE-FG-W19
KE-FG-W20
KE-FG-W21
KE-FG-W22
KE-FG-W23
KE-FG-W24
KE-FG-W58
KE-FG-W60
KE-FG-W77
KE-FG-W125
KE-FG-W130
KE-FG-W140
KE-FG-W150
KE-FG-W160
KE-FG-W170
SIZE (WxH)
18 x 2.0
20 x 2.0
20 x 3.5
21 x 1.0
21 x 2.0
21 x 2.5
21 x 3.7
21 x 4.0
25 x 1.0
25 x 2.0
27 x 2.0
30 x 3.0
31 x 1.0
31 x 2.0
31 x 3.0
32 x 1.0
35 x 2.0
38 x 2.0
40 x 1.0
40 x 2.0
45 x 2.0
55 x 2.5
55 x 3.0
60 x 2.0
KE-FG-W29 19.1 x 1.0
KE-FG-W30 21.8 x 1.0
KE-FG-W38 38.5 X 2.0
KE-FG-W41 41.0 x 3.5
19.1 x 2.0
21.8 x 2.0
21.7 x 3.7
55 x 1.2
25.4 x 1.0
25.4 x 1.5
18 x 1.0
41.8 x 1.0
43.5 x 2.5
PROFILE NO SIZE (WxH)
KE-FG-P01 8.0 x 2.0
KE-FG-P02 8.0 x 4.0
KE-FG-P03 13.2 x 3.3
KE-FG-P04 16 x 4.5
↔
H
KE-FG-P10 13.2 X 4.0
KE-FG-P91 8.0 X 3.0
KNIFE EDGE PROFILE
W
PROFILE NO SIZE (WxH)
KE-FG-K01 11.3 x 2.5
KE-FG-K02 12.7 x 2.5
KE-FG-K03 19.7 x 6.4
KE-FG-K04 12.7 x 2.7
(2x adhesive as standard)
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
54
SHIELDING

FOAMGASKET
KIT
SOFT FOAM ENGINEERING LAB KITS
A selection of our most popular profiles are available in
lab kit with 600mm length.
55
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

CUSTOMISED
GASKET
Notching, punching, sub-assembly
fabrication and die cutting also available.
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
56
SHIELDING

SHIELDING
PART NUMBER GUIDE
KITAGAWA EMI Shielding Gasket
Profile No.
D = D-Profile
F = Flat Profile
C = C-Fold Profile
R = Rectangular Profile
K = Knife Edge Profile
P = P-Profile
W = Wide Profile
(I.O. Gasket)
Tape of fabric
VNN Standard EMI Gasket with Ripstop Fabric and NiCu
coating, UL94-VO
GLD Gold Gasket with Tatteta Fabric and Au coating
BLK Black Gasket with Ripstop Fabric and Carbon
coating
Tape of Adhesive
T with adhesive
N without adhesive
D with conductive adhesive
KT adhesive with kisscut
finish(half cuton liner)
KD conductive adhesive
with kisscut finish
(half cut on liner)
KE-FG-D01VNN0500TSP
KITAGAWA Foam Gasket
Length (in mm)
Suffix SP is added in case of any special option like Die Cut
57
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

SHIELDING
CONDUCTIVE
Features:
FOAM
Kitagawa Conductive Foam provides
excellent X,Y and Z axis conductivity
and offers very good shielding and
grounding effectiveness.
The Foam is designed for low-cycling
applications such as I/O-shielding and
is easy to fix, cut and punch to customers
specification.
Product No:
DECF - 000P
Structure:
P.U coating
Conductive foam
Mesh
Conductive adhesive
Release liner
Characteristics:
Item Standard Reference
Material
P.U. Coating
Conductive foam
Mesh
Adhesive
Release Liner
Conductive adhesive resin composition
Lead (Pb) content
Cadmium (Cd) content
Mercury (Hg) content
Chromium VI (Cr 6+ ) content
Temperature Limit (°C)
Adhesive Strength
(180°peel * gf/ 25mm)
Holding Strength (sec)
Volume conductivity (Ω / sq)
Polymer resin : Polyurethane (conductive)
Polyurethane foam (Copper and Nickel Plated)
Polyester woven mesh with Copper and Nickel plated
Both side conductive adhesive
CP paper (avg 70 μm)
Acrylic ester polyol copolymer + Nickel powder
ISO 6101-2
Not detected
Analytical instrument : AAS
EN 1122
Not detected
Analytical instrument : ICP
ISO 3856/7
Not detected
Analytical instrument : AAS
ISO 3856/5
Not detected
UV-Vis. Spectrophotometer
-10 ~ 60
26°C * 60% R.H.
800
SUS 304Plate 30min, 300mm/min
3.600
PET film (25 μm), 40°C, 500g
0,2
EMQI-1031 ( Inch / 0.5Kgf )
➝
➝
➝
Part list:
Part No
DECF-005P
DECF-008P
DECF-010P
DECF-013P
DECF-015P
DECF-020P
DECF-040P
Thickness (mm)
0.5+/-0.2
0.8+/-0.2
1.0+/-0.2
1.3+/-0.2
1.5+/-0.2
2.0+/-0.3
4.0+/-0.3
KE KITAGAWA
Width (mm)
300
300
300
300
300
500
500
Length (m)
50m / roll
50m / roll
50m / roll
50m / roll
50m / roll
50m / roll
50m / roll
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
58
SHIELDING

Ripstop
SHIELDING
SHIELDING
FABRIC
Features:
Conductive fabric is a kind of matarial which conductivity is
endowed by being plated with copper and nickel by non-electrolytic
process on all types of polyester fabrics. This material
is properly applied to the wide range of EMI shielding products
which various designs and sepcitications are required by
engineers because the material has good conductivity and
excellent EMI shielding effectiveness to 30MHz 10GHz frequency
bands. Conductive fabric is easy to shape, light in
weight and the plating materials have good abrasion resistance.
Application:
EMI Gaskets, Conductive Fabric Tapes, ESD,
Cable Shield, shield Case, Shield Sheet, etc.
Shielding Effectivenss(dB)
100
90
80
70
60
50
40
30
20
10
0
0 10 20 30 40 50 60 70 80 90 100
Shielding Effectivenss(dB)
100
90
80
70
60
50
40
30
20
10
0
0 10 20 30 40 50 60 70 80 90 100
Frequency(MHz)
Frequency(MHz)
KE-E2-235C-H
KE-E2-235S-H
Shielding Effectivenss(dB)
100
90
80
70
60
50
40
30
20
10
0
0 10 20 30 40 50 60 70 80 90 100
Frequency(MHz)
Shielding Effectivenss(dB)
100
90
80
70
60
50
40
30
20
10
0
0 10 20 30 40 50 60 70 80 90 100
Frequency(MHz)
KE-E1-290C-H
KE-E1-290G-H
59
KE KITAGAWA
Elbinger Straße 3-5 3-5 · · D-63110 Rodgau-Jügesheim · FR-Germany · · Telefon · 0 061 61 06/85 24 24 - 0 - 0 · Telefax · 0 061 61 06/85 24-30 (31) (31)

SHIELDING
SHIELDING
FABRIC
Specification of Conductive Fabric
Product No
Type
base
Material
metal
Width
(mm)
Length
(m)
Thickness
(mm)
Max.short
duration
Temp.(°C)
Surface resistance
(Ohm/cm2)
Shielding
Effectiveness
(dB)(30Mhz-1GHz)
KE-E1-290C-H
KE-E1-290G-H
KE-E2-235C-H
KE-E2-235S-H
KE-E3-50C-H
KE-E4-130C-H
Woven
Woven
Ripstop
Ripstop
Non Woven
Mesh
polyester
Cu+Ni
Cu+Ni+Au
Cu+Ni
Cu+Ni+Ag
Cu+Ni
Cu+Ni
1040 50
0.1
0.1
0.09
0.1
0.16
0.07
210
≤0.05
≤0.05
≤0.05
≤0.05
≤0.05
≤0.05
60-70
65-75
60-70
70-80
68-75
60-70
Basic Material Test Result (Conductive Fabric)
Tensile Strength(kgf) Extention (%) Fabric Count (thread/inch) Weight (g/m2)
Warp Weft Warp Weft Warp weft
KE-E2-235C-H 49.7 38.3 23.6 27.9 128.8 113.4 73.1
KE-E1-290C-H 68.5 40.0 27.6 30.8 184.0 91.0 76.0
KE-E2-235S-H 50.2 33.5 28.8 29.6 128.8 113.4 73.1
KE-E1-290G-H 60.5 28.8 27.1 27.0 184.0 91.0 76.0
Construction
Theory of EMI shielding
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
60
SHIELDING

SHIELDING
D-SUB
CONNECTOR-GASKETS
EMI SHIELDING FOR ALL STANDARD
SIZES. Our new I/O Shielding (IOS)
gaskets enhance the performance of
EMI shielding for D-Sub Connectors.
Sized to fit standard D-Subminiature
connectors, IOS gaskets provide multiple
contact points to maintain conductivity,
and compensate for tolerance stackup.
Pressure-sensitive adhesive (PSA) tape
is available, but not usually required
for installation.
With no tooling costs, easy installation,
and off-the-shelf availability, these gaskets
are a simple and efficient solution
to I/O shielding.
D
A
C
E
B
t
Type
9 Pins D09
15 Pins D15
25 Pins D25
37 Pins D37
50 Pins D50
A
33.4
41.7
55.6
71.9
69.6
B
19.1
19.1
19.1
19.1
21.8
C
17.4
25.7
39.6
55.9
53.6
D
10.0
10.0
10.0
10.0
12.0
E
25.4
36.7
47.6
63.9
61.6
t=1mm
W29
W29
W29
W29
W30
t=2mm
W58
W58
W58
W58
W60
Profile Number
W29
W58
W30
W60
Connector Type
D09
D15
D25
D37
D50
With adhesive tape T
Without adhesive N
KE-FG-W29VNND09T
Foam Gasket
VNN
Standard EMI Gasket with
Ripstop Fabric and NiCu
coating, UL94-VO
61
KE KITAGAWA
Elbinger Straße 3-5 3-5 · · D-63110 Rodgau-Jügesheim · FR-Germany · · Telefon · 0 061 61 06/85 24 24 - 0 - 0 · Telefax · 0 061 61 06/85 24-30 (31) (31)

SHIELDING
CARBON
RUBBER
CARBON RUBBER is a carbon filled
silicone rubber available in the form of
sheet as well as various extruded
shapes as shown here.
CARBON RUBBER is a good shielding
material and an excellent environmental
seal.
Material specifications
Material. conductive silicone (black)
Continuous use temperature range:
-60~200°C
Hardness: 60±5 (JISA) JIS C2123
Tensile Strenght: >50 kg/cm 2 JIS C2123
Tensile elongation: >200% JIS C2123
Volume resistivity: 3~10 Ω cm
Flammability: UL94V-O
„O“ Section
Round Section
Part No.
CSR-O-25-15
CSR-O-60-30
CSR-O-65-30
CSR-O-100-65
„D“ Section
O.D
2.5
6.0
6.5
10.0
I.D
1.5
3.0
3.0
6.5
Part No.
CSR-R-15
CSR-R-20
CSR-R-30
CSR-R-40
CSR-R-60
„P“ Section
D
1.5
2.0
3.0
4.0
6.0
Part No.
CSR-D-40-15
CSR-D-45-25
„U“ Section
A
4.0
4.5
B
1.5
2.5
Part No.
CSR-P-125-50
CSR-P-170-72
CSR-P-240-77
A
12.5
17.0
24.0
B
5.0
7.2
7.7
C
6.0
7.5
11.0
Part No.
CSR-U-48-48
CSR-U-55-110
CSR-U-80-130
CSR-U-95-130
A
4.8
5.5
8.0
9.5
B
4.8
11.0
13.0
13.0
C
3.2
8.0
9.5
9.5
D
1.6
2.5
3.5
5.0
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
62
SHIELDING

SHIELDING
CONDUCTIVE
Features
ELASTOMER
- The Kitagawa Electrically Conductive Elastomers offer excellent shielding
and environmental sealing. They are offered in a range of materials and
outlines to meet various applications.
Dimension + Technical Data
Material:
Conductive particles (nickel) in Silicon
Shore A hardness: 68 +/- 6
Volume resistivity ( Ohm / cm ) 0.1
Temperature range (°C ) -55 to +200
Density ( g/cm 3 ) 3.5
Tensile strength ( % ) 75
Colour
black
Shielding effectiveness ( dB ) H-Field 10 KHz 72
E-Field 1 MHz 115
P-Field 1 GHz 85
Tolerance (mm)
+/- 0.08
+/ - 0.13
+/ - 0.15
+/ - 0.20
+/ - 0.20
Standard Sheets - PL -
Part No.
SG-PL-
SG-PL-
SG-PL-
SG-PL-
SG-PL-
A(mm)
200.00
200.00
200.00
200.00
200.00
B (mm)
-200.00
-200.00
-200.00
-200.00
-200.00
T (mm)
-0.50
-0.80
-1.00
-1.50
-2.00
Custom Gaskets can be cut to customer specification!
Rectangular Strips - R E -
Part No.
SG-RE-
SG-RE-
SG-RE-
SG-RE-
SG-RE-
A (mm)
1.00
1.50
2.00
2.00
2.00
B (mm)
-3.00
-3.00
-2.50
-3.00
-4.00
L (mm)
-1.500.oo
-1.500.00
-1.500.00
-1.500.00
-1.500.00
Tolerance (mm)
A
B
+/ - 0.08 +/ - 0.12
+/ - 0.12 +/ - 0.12
+/ - 0.18 +/ - 0.12
+/ - 0.18 +/ - 0.12
+/ - 0.18 +/ - 0.12
63
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

SHIELDING
CONDUCTIVE
Features
ELASTOMER
- The Kitagawa Conductive Elastomer EMI-Gaskets feature an abrasionresistant,
silver-filled elastomer applied over a non-conductive extruded
silicon core.
Technical data (coating only)
Material:
Ag/Cu particles in Silicon
Volume resistivity ( Ohm / cm ) 0,008
Temperature resistance (°C ) 125
Density ( g/cm 3 ) 3,6
Coating thickness ( mm ) 0,15 +/-0,05
Breaking elongation ( % ) 125
Colour
beige
Shielding effectiveness ( dB ) H-Field 10 kHz 67
E-Field 1 MHz 130
P-Field 1 GHz 110
Elastomer core:
Silicon foam (non conductive)
Density 0,43 g/cm 3
Shore A hardness 30°+/-6
Breaking elongation >90 %
Compression Set < 40 %
Temperature resistance -55/+125° C
Elastomer core:
Silicon tube (non conductive)
Density 1,14 g/cm 3
Shore A hardness 60°+/-6
Breaking elongation >45 %
Compression Set < 35 %
Temperature resistance -55/+125° C
Elastomer core:
Silicon solid round (non conductive)
Density 1,08 g/cm 3
Shore A hardness 60° +/- 7
Breaking elongation >180 %
Compression Set < 35%
Temperature resistance -55/+125° C
Part No. D A (mm) Tolerance (mm)
SG-FO-1.50 +/- 0.18
SG-FO-1.80 +/- 0.20 3
SG-FO-2.00 +/- 0.20
SG-FO-2.30 +/- 0.20
SG-FO-2.50 +/- 0.25
SG-FO-2.80 +/- 0.25
SG-FO-3.00 +/- 0.25
SG-FO-3.30 +/- 0.25
SG-FO-3,80 +/- 0.30
SG-FO-4.00 +/- 0.30
SG-FO-4.30 +/- 0.30
SG-FO-4.50 +/- 0.30
SG-FO-4.80 +/- 0.35
SG-FO-5.o0 +/- 0.35
SG-FO-5.30 +/- 0.35
SG-FO-5.50 +/- 0.35
SG-FO-6.00 +/- 0.35
Max. available outer diameter 7.50 mm
Part No. D A D I (mm) Tolerance (mm)
SG-TU- 1.30 -0.50 +/- 0.15
SG-TU- 1.50 -0.50 +/- 0.15 3
SG-TU- 1.60 -0.50 +/- 0.20
SG-TU- 1.80 -1.00 +/- 0.20
SG-TU- 2.00 -1.00 +/- 0.20
SG-TU- 2.10 -1.00 +/- 0.20
SG-TU- 2.30 -1.00 +/- 0.20
SG-TU- 2.60 -1.00 +/- 0.25
SG-TU- 3.00 -1.00 +/- 0.25
SG-TU- 3.00 -1.50 +/- 0.25
SG-TU- 3.30 -1.50 +/- 0.25
SG-TU- 3.60 -1.50 +/- 0.25
SG-TU- 4.10 -1.50 +/- 0.25
SG-TU- 4.80 -2.00 +/- 0.30
SG-TU- 5.30 -2.00 +/- 0.30
SG-TU- 5.80 -2.00 +/- 0.35
KE KITAGAWA
Part No. D A (mm) Tolerance (mm)
SG-RO-1.20 +/- 0.15
SG-RO-1.50 +/- 0.15 3
SG-RO-1.80 +/- 0.15
SG-RO-2.00 +/- 0.15
SG-RO-2.30 +/- 0.20
SG-RO-2.50 +/- 0.20
SG-RO-2.80 +/- 0.25
SG-RO-3.00 +/- 0.25
SG-RO-3.30 +/- 0.25
SG-RO-3.50 +/- 0.25
SG-RO-3.80 +/- 0.25
SG-RO-4.00 +/- 0.30
SG-RO-4.30 +/- 0.30
SG-RO-4.50 +/- 0.30
SG-RO-4.80 +/- 0.30
SG-RO-5.50 +/- 0.35
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
64
SHIELDING

SHIELDING
ALL METAL GASKETS
Features
- Simplest method of maintaining electrical continuty between two
mating surface
- Highest attenuation level (according to MIL-285) during operative life
- No temperature limits
- Fabricated and cut-to-length gaskets
- Pressure sensitive adhesive (as an option)
Material
- Monel (MO)
- Tinned copper clad steel (TC)
- Stainless steel (SL)
Tolerances
1,5-5 mm +0,4 - 0 mm
6-10 mm +0,6 - 10 mm
> 10 mm +0,8 - 0 mm
- Berillium copper (BC)*
- Tinned copper (TR)*
- Phosphor bronze (PB)*
- Aluminium (AL)*
*upon request
Ordering information: Complete the P/N with the 2-letter Metall Suffix i.e. MG-R.032.064.MO or MG-B.080.254.SL
Round Rectangular P section Double P section
P/N
Diameter
(mm)
P/N Height Width
(mm) (mm)
P/N
Diameter Width
(mm) (mm)
P/N
Diameter Width
(mm) (mm)
MG-T.016
MG-T.024
MG-T.032
MG-T.048
MG-T.064
MG-T.080
MG-T.095
MG-T.111
MG-T.127
MG-T.159
MG-T.191
1.6
2.4
3.2
4.8
6.4
8.0
9.5
11.1
12.7
15.9
19.1
MG-R.024.024
MG-R.024.048
MG-R.024.064
MG-R.032.032
MG-R.032.064
MG-R.032.080
MG-R.048.048
MG-R.048.080
MG-R.048.127
MG-R.064.064
MG-R.064.127
MG-R.080.127
MG-R.095.127
2.4
2.4
2.4
3.2
3.2
3.2
4.8
4.8
4.8
6.4
6.4
8.0
9,5
2.4
4.8
6.4
3.2
6.4
8.0
4.8
8.0
12.7
6.4
12.7
12.7
12.7
MG-P.032.095
MG-P.032.127
MG-P.032.159
MG-P.032.191
MG-P.048.127
MG-P.048.159
MG-P.048.191
MG-P.048.222
MG-P.080.159
MG-P.080.191
MG-P.080.222
MG-P.080.254
MG-P.095.320
3.2
3.2
3.2
3.2
4.8
4.8
4.8
4.8
8.0
8.0
8.0
8.0
9.5
9.5
12.7
15.9
19.1
12.7
15.9
19.1
22.2
15.9
19.1
22.2
25.4
32.0
MG-B.032.095
MG-B.032.127
MG-B.032.159
MG-B.032.191
MG-B.048.159
MG-B.048.191
MG-B.048.222
MG-B.048.254
MG-B.080.191
MG-B.080.222
MG-B.080.254
MG-B.080.320
MG-B.095.320
3.2
3.2
3.2
3.2
4.8
4.8
4.8
4.8
8.0
8.0
8.0
8.0
9.5
9.5
12.7
15.9
19.1
15.9
19.1
22.2
25.4
19.1
22.2
25.4
32.0
32.0
Other sizes, configurations or ready-to-mount finished gaskets (according to your drawing)
available upon request
65
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

SHIELDING
WIRE MESH OVER ELASTOMER CORE GASKETS
Features
- Improved resiliency combined with dust and moisture sealing.
- Excellent attenuation characteristics (95-100dB in E-field,
45-90dB in H-field).
- Fabricated and cut-to-length gaskets.
- Pressure sensitive adhesive (as an option).
Material
Wide range of core:
- Neoprene sponge (-40 °C to + 85 °C) (NS)
- EPDM sponge (-40 °C to + 100 °C) (ES)
- Silicone sponge (-50 °C to + 200 °C) (SS)
- Silicone tubing (-50 °C to + 200 °C) (ST)
- Low density foam (-30 °C to + 80 °C) (LF)*
and wire materials:
- Monel (MO)
- Tinned copper clad steel (TC)
- Stainless steel (SL)
Tolerances
1.5-5 mm +/- 0.3 mm
6-12 mm +/- 0.6 mm
> 12 mm +/- 0.9 mm
- Berillium copper (BC)*
- Tinned copper (TR)*
- Phosphor bronze (PB)*
- Aluminium (AL)*
*upon request
Ordering information:
Complete the P/N with i.e. MG-BE.048.159.ST.2-MO
- the 2- letter core suffix Double P section, 3.2 x 15,9 mm, 2 layers of monel wire over silicon tube
- the number of layers (2 is standard) i.e. MG-RE.064.064.NS.3-TC
- the 2-letter metal suffix Square section, 6.4 x 6.4 mm, 3 layers of tin copper clad steel wire on
neoprene sponge
Round Rectangular P section Double P section
P/N
Diameter
(mm)
P/N Height Width
(mm) (mm)
P/N
Diameter Width
(mm) (mm)
P/N
Diameter Width
(mm) (mm)
MG-TE.016
MG-TE.024
MG-TE.032
MG-TE.050
MG-TE.064
MG-TE.080
MG-TE.095
MG-TE.111
MG-TE.127
MG-TE.159
MG-TE.191
1.6
2.4
3.2
5.0
6.4
8.0
9.5
11.1
12.7
15.9
19.1
MG-RE.024.024
MG-RE.024.048
MG-RE.024.064
MG-RE.032.032
MG-RE.032.064
MG-RE.032.080
MG-RE.048.048
MG-RE.048.080
MG-RE.048.127
MG-RE.064.064
MG-RE.064.127
MG-RE.080.127
MG-RE.095.127
2.4
2.4
2.4
3.2
3.2
3.2
4.8
4.8
4.8
6.4
6.4
8.0
9.5
2.4
4.8
6.4
3.2
6.4
8.0
4.8
8.0
12.7
6.4
12.7
12.7
12.7
MG-PE.032.095
MG-PE.032.127
MG-PE.032.159
MG-PE.032.191
MG-PE.048.127
MG-PE.048.159
MG-PE.048.191
MG-PE.048.222
MG-PE.080.159
MG-PE.080.191
MG-PE.080.222
MG-PE.080.254
MG-PE.095.320
3.2
3.2
3.2
3.2
4.8
4.8
4.8
4.8
8.0
8.0
8.0
8.0
9.5
9.5
12.7
15.9
19.1
12.7
15.9
19.1
22.2
15.9
19.1
22.2
25.4
32.0
MG-BE.032.095
MG-BE.032.127
MG-BE.032.159
MG-BE.032.191
MG-BE.048.159
MG-BE.048.191
MG-BE.048.222
MG-BE.048.254
MG-BE.080.191
MG-BE.080.222
MG-BE.080.254
MG-BE.080.320
MG-BE.095.320
3.2
3.2
3.2
3.2
4.8
4.8
4.8
4.8
8.0
8.0
8.0
8.0
9.5
9.5
12.7
15.9
19.1
15.9
19.1
22.2
25.4
19.1
22.2
25.4
32.0
32.0
Other sizes, configurations or ready-to-mount finished gaskets (according to your drawing)
available upon request
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
66
SHIELDING

SHIELDING
MULTISTRIP
GASKETS
Features
- Combination of knitted wire mesh bonded to an elastomer which
provides an EMI shield as well as an environmental sealing
- Complete choice of knitted wire materials
- Pressure sensitive adhesive on elastomer for easy application
- Customized and cut-to-length gaskets
Material
Range of elastomer strips:
- Neoprene sponge (-40 °C to + 85 °C) (NS)
- EPDM sponge (-40 °C to + 100 °C) (ES)
and wire materials:
- Monel (MO)
- Tinned copper clad steel (TC)
- Stainless steel (SL)
- Berillium copper (BC)*
- Tinned copper (TR)*
- Phosphor bronze (PB)*
- Aluminium (AL)*
*upon request
Tolerances
Elastomer
2-3 mm ±0,4 mm
4-12 mm ±0,8 mm
Knitted mesh
2-5 mm +0,4 - 0 mm
6-10 mm +0,5 - 0,3 mm
>10 mm +1,2 - 0,5 mm
Ordering information:
Complete the P/N with i.e. MG-REM.032.032.159.SS.TR
- the 2-letter elastomer suffix Single 3.2 x 3.2 mm tinned copper mesh combined to 3.2 x 15.9 mm
silicone sponge.
- the 2-letter metal suffix i.e. MG-REDM.032.064.095.NS.MO
Double 3.2 x 6.4 mm monel mesh combined to 3.2 x 9.5 mm neoprene sponge
Single
Double
P/N Mesh Elastomer
Height Width Width
(mm) (mm) (mm)
MG-REM.024.032.095
MG-REM.032.032.127
MG-REM.032.032.159
MG-REM.032.064.127
MG-REM.048.048.127
MG-REM.048.064.159
MG-REM.048.064.191
MG-REM.048.095.127
MG-REM.064.064.159
MG-REM.064.095.191
MG-REM.095.064.127
MG-REM.095.064.191
2.4
3.2
3.2
3.2
4.8
4.8
4.8
4.8
6.4
6.4
9.5
9.5
3.2
3.2
3.2
6.4
4.8
6.4
6.4
9.5
6.4
9.5
6.4
6.4
9.5
12.7
15.9
12.7
12.7
15.9
19.1
12.7
15.9
19.1
12.7
19.1
P/N Mesh Elastomer
Height Width Width
(mm) (mm) (mm)
MG-REDM.032.032.064
MG-REDM.032.032.095
MG-REDM.032.032.127
MG-REDM.032.064.095
MG-REDM.032.064.127
MG-REDM.048.032.064
MG-REDM.048.032.127
MG-REDM.048.064.127
3.2
3.2
3.2
3.2
3.2
4.8
4.8
4.8
3.2
3.2
3.2
6.4
6.4
3.2
3.2
6.4
6.4
9.5
12.7
9.5
12.7
6.4
12.7
12.7
Other sizes, configurations or ready-to-mount finished gaskets (according to your drawing)
available upon request
67
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

SHIELDING
SYNTHETIC YARN KNITTED GASKETS
Features
- Silver plated synthetic yarn knitted over elastomer
- Optimal electric conductivity of every single fiber
- High coverage knitted yarn for wide contact surface and shielding
- Smooth and soft surface gasket
- Self- terminating cut ends
- Pressure sensitive adhesive
- Customized and cut-to-length gaskets
- Shielding efficiency as high as 100 dB in a frequency range of
1 MHz to 1 GHz (E-field)
- Standard core material: neoprene sponge
Other core materials available upon request
Tolerances
- ± 0,75 mm
Round Rectangular D section
P/N
Diameter
(mm)
P/N Height Width
(mm) (mm)
P/N Height Width
(mm) (mm)
MG-YTE.016
MG-YTE.024
MG-YTE.032
MG-YTE.048
MG-YTE.064
MG-YTE.080
MG-YTE.095
MG-YTE.111
MG-YTE.127
MG-YTE.159
MG-YTE.191
1.6
2.4
3.2
4.8
6.4
8.0
9.5
11.1
12.7
15.9
19.1
MG-YRE.024.024
MG-YRE.024.048
MG-YRE.024.064
MG-YRE.032.032
MG-YRE.032.064
MG-YRE.032.080
MG-YRE.048.048
MG-YRE.048.080
MG-YRE.048.127
MG-YRE.064.064
MG-YRE.064.127
MG-YRE.080.127
MG-YRE.095.127
2.4
2.4
2.4
3.2
3.2
3.2
4.8
4.8
4.8
6.4
6.4
8.0
9.5
2.4
4.8
6.4
3.2
6.4
8.0
4.8
8.0
12.7
6.4
12.7
12.7
12.7
MG-YDE.048.064
MG-YDE.064.095
MG-YDE.064.127
MG-YDE.095.127
4.8
6.4
6.4
9.5
6.4
9.5
12.7
12.7
Other sizes, configurations or ready-to-mount finished gaskets (according to your drawing)
available upon request
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
68
SHIELDING

SHIELDING
SPRING SERIES GASKETS
Features
- Minimum compression force and high resiliency gaskets
- Optimum attenuating properties :
copper beryllium, E-field
tin copper clad steel, H-field
(combination of 2 materials is possible)
- 100% free height recovery after deflection during operative life
- No moisture absorption
- Fabricated and cut-to-length gaskets
- Pressure sensitive adhesive (on „D“ shape gaskets)
Material
- Beryllium Copper (BC)
- Stainless steel (SL)*
- Tinned Copper Clad Steel (TC)*
(only in combination with BC or SL)
*upon request
Tolerances
1,5-5 mm +0,4 - 0 mm
6-10 mm +0,6 - 10 mm
> 10 mm +0,8 - 0 mm
Ordering information:
Complete the P/N with i.e. MG-SB.032.127.1-SL
- the number of wires Double P section, 3.2 x 12.7 mm, 1 stainless steel wire
- the 2-letter metal suffix MG-SD.080.095.2-BC
D section, 8.0 x 9.5 mm, 2 beryllium copper wires
Round P section Double P section D section
P/N
Diameter
(mm)
P/N
Diameter Width
(mm) (mm)
P/N
Diameter Width
(mm) (mm)
P/N
Height Width
(mm) (mm)
MG-ST.016
MG-ST.024
MG-ST.032
MG-ST.048
MG-ST.064
MG-ST.080
MG-ST.095
MG-ST.111
MG-ST.127
1.6
2.4
3.2
4.8
6.4
8.0
9.5
11.1
12.7
MG-SP.016.095
MG-SP.024.127
MG-SP.032.127
MG-SP.032.159
MG-SP.048.159
MG-SP.064.191
MG-SP.064.254
MG-SP.080.254
MG-SP.095.320
1.6
2.4
3.2
3.2
4.8
6.4
6.4
8.0
9.5
9.5
12.7
12.7
15.9
15.9
19.1
25.4
25.4
32.0
MG-SB.024.127
MG-SB.032.127
MG-SB.032.159
MG-SB.048.159
MG-SB.048.191
MG-SB.064.191
MG-SB.064.254
MG-SB.080.254
MG-SB.090.320
2.4
3.2
3.2
4.8
4.8
6.4
6.4
8.0
9.5
12.7
12.7
15.9
15.9
19.1
19.1
25.4
25.4
32.0
MG-SD.032.051
MG-SD.048.064
MG-SD.064.080
MG-SD.080.095
MG-SD.095.127
3.2
4.8
6.4
8.0
9.5
5.1
6.4
8.0
9.5
12.7
Other sizes, configurations or ready-to-mount finished gaskets (according to your drawing)
available upon request
69
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

SHIELDING
MESH TAPES
Features
- Especially designed for shielding and grounding of electrical and
electronic cable assemblies
- Flexible structure to conform to irregular surfaces and contours
during the wrapping process (50% overlap bandage)
- Tin plating to allow solderability
- Useful for static discharge (ESD)
- Tin copper clad steel is standard material (best performance),
several other alloys and wire diameters available
Material
- Tinned copper clad steel (TC)
- Tinned copper (TR)
- Stainless steel (SL)
- Monel (MO)
- Brass (BR)
Tolerances
up to 20mm +/-0.8mm
21 - 50mm +/-1.3mm
51 - 155mm +/-2.0mm
Ordering information:
Complete the P/N with the 2-letter metal suffix i.e. MG-C.0127.TC
Tape 12.7 mm width, tin copper clad steel wire
MG-C.0501.BR
Tape 50.1 mm width, brass wire
P/N
Width
(mm)
MG-C.0127
12.7
MG-C.0191
MG-C.0254
MG-C.0508
MG-C.0762
MG-C.1016
19.1
25.4
50.8
76.2
101.6
Frequency
1 MHz
10 MHz
100 MHz
1 GHz
TC
78
66
60
55
MO
70
64
60
56
Attenuation [dB]
SL
69
61
58
51
Al
73
63
58
56
TR
73
65
59
54
MG-C.1524
152.4
10 GHz
40
42
37
44
40
supplied in 50m rolls
Note: These values are indicative only and are for 50% overlap, giving effective 4 layers of mesh for shielding
OEM CUSTOMER MADE PRODUCTS
Wire mesh & elastomer composites
Layers of knitted wire forming sections of varying
construction with or without an elastomer core.
They can be supplied, to suit the application,
with any of the above variants fitted to a seperate
elastomer carrier or incorporated in an aluminium
carrier.
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
70
SHIELDING

SHIELDING
COPPER BERYLLIUM FINGER STRIPS
Features
Copper beryllium owes its wide range of application to the unique performance
qualities it has:
- extraordinary elasticity
- strength
- fatigue strength
- high conductivity
- resistance against environmental influences such as ozone, epipolar
rays and light, also against solvents and corrosion.
- Furthermore, copper beryllium can be used under a wide temperature range
and is not burnable or flammable. It does not evolve gas either. If handled
correctly, it acts self purificating, for example when it is employed as a door
shield for opening and closing.
Technical Data
Specific gravity: 8,4 g/cm 3
Fusing point: 900 °C
Coefficient of expansion (20-200 °C) 17 10 -6 /°C
Thermal conductivity: 0.27 cal/cm s °C; 1.13 W/cm °C
Diamond pyramid hardness: 350-430 kp/mm 2
Tensile strength: 1200-1450 N/mm 2
Fatigue strength, load application 10 8 : 250-290 N/mm 2
Modulus of elasticity: 135000 N/mm 2
Torsion modulus: 47000 N/mm 2
Spring bending limit: 820-950 N/mm 2
Electric conductivity: 12.5-13 m/Ωmm 2
Technical data can be subject to alteration
Plating finishes:
-01 Bright finish
-02 Tin plated
-03 Silver plated
-04 Nickel plated
-05 Gold plated
Ordering information: Part No. Finish-ID. length (mm)
CB- xxxx - xx - xxxxx
CB-0002
A
mm
B
mm
A
CB-0002 5.84 3.56
B
copper beryllium 0.08 mm/ 500 mm, endless, with adhesive tape
71
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

SHIELDING
COPPER BERYLLIUM FINGER STRIPS
CB-0003
CB-0004
A
B
A
mm
B
mm
CB-0003 7.60 3.53
CB-0004 8.64 4.57
copper beryllium 0.08 mm/ 500 mm, endless, with adhesive tape
CB-0005
CB-0006
CB-0007
(-0006) (-0007)
copper beryllium 0.08 mm/ 500 mm, endless, with adhesive tape
copper beryllium 0.08 mm/ 500 mm, with adhesive tape
CB-0008
CB-0009
CB-0010
(-0008) (-0009)
copper beryllium 0.08 mm/ 500 mm, with adhesive tape
copper beryllium 0.07 mm/ 500 mm, endless, with adhesive tape
xx
CB-0011
CB-0012
xx
copper beryllium 0.08 mm/ 406 mm, endless, with adhesive tape
copper beryllium 0.09mm/ 609,6 mm and 7620 mm, with adhesive tape
CB-0013
- CB-0015
B
E
F
CB-0013
A
8.1
B
2.8
C
5.3
D
0.05
E
4.3
F
0.5
L
406
mm
A
C
CB-0014
9.4
3.3
5.3
0.05
5.7
0.6
406
mm
L
D
CB-0015 15.2 5.6 7.1 0.08 8.7 0.8 406
with adhesive tape
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
mm
72
SHIELDING

SHIELDING
COPPER BERYLLIUM FINGER STRIPS
CB-0016 - CB-0021
0.4
2
A
0.8
C
0.076
CB-0016
CB-0017
CB-0018
CB-0019
A
3.8
3.8
4.1
4.1
B
1.0
1.5
1.0
1.5
C
3.0
2.5
4.0
3.5
L
406
406
406
406
mm
mm
mm
mm
B
CB-0020
CB-0021
5.8
5.8
1.0
1.5
4.0
3.5
406
406
mm
mm
CB-0022 - CB-0027
0,4
3.8
1.78
0.076
CB-0022
CB-0023
A
4.8
4.8
B
1.0
1.5
C
3.3
3.0
L
406
406
mm
mm
CB-0024
4.8
2.0
2.8
406
mm
A
C
CB-0025
6.4
1.0
5.1
406
mm
CB-0026
6.4
1.5
4.6
406
mm
B
CB-0027
6.4
2.0
4.1
406
mm
CB-0034
B
CB-0034
Oblong hole
no
copper beryllium 0.13 mm/ 406 mm and 500 mm
CB-0036
CB-0037
xx
copper beryllium 0.13 mm/ 500 mm, endless
copper beryllium 0.09 mm/ 59 mm
CB-0038 - CB-0039
A
B
A
mm
B
mm
CB-0038 3.2 1.5
CB-0039 8.0 1.5
500
73
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

SHIELDING
COPPER BERYLLIUM FINGER STRIPS
CB-0042
CB-0044
copper beryllium 0.13 mm/ 500 mm
copper beryllium 0.13 mm/ 500 mm, with T-lance
CB-0045
CB-0046
copper beryllium 0.13 mm/ 500 mm and coil, 10m
copper beryllium 0.13 mm/ 500 mm and coil, 10 m, with oblong hole
CB-0048
CB-0049
B
A
A
mm
B
mm
CB-0048 9.1 7.7
CB-0049 11.5 9.8
copper beryllium 0.2 mm/ 500 mm
CB-0050
CB-0051
C
A B C
mm mm mm
B
A
CB-0050 9.5 6.4 7.0
CB-0051 12.0 8.4 8.0
copper beryllium 0.2 mm/ 500 mm
CB-0057
copper beryllium 0.2 mm/ 500 mm
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
74
SHIELDING

SHIELDING
COPPER BERYLLIUM FINGER STRIPS
CB-0059
A
mm
CB-0059 18.5
copper beryllium 0.2 mm/ 500 mm
CB-0060
CB-0061
A
mm
A
CB-0060 13.8
CB-0061 18.3
copper beryllium 0.2 mm/ 500 mm
CB-0062
CB-0063
A
mm
CB-0062 11.0
A
CB-0063 15.0
copper beryllium 0.13 mm/ 500 mm
CB-0064
CB-0065
A
A
mm
A
CB-0064 11.0
CB-0065 15.0
copper beryllium 0.2 mm/ 500 mm
75
KE KITAGAWA
Elbinger Straße 3-5 3-5 · · D-63110 Rodgau-Jügesheim · FR-Germany · · Telefon · 0 061 61 06/85 24 24 - 0 - 0 · Telefax · 0 061 61 06/85 24-30 (31) (31)

SHIELDING
COPPER BERYLLIUM FINGER STRIPS
CB-0121
23.72
2.03
0.38
50° ø2
4.06
1.18 1.30
19.05
copper beryllium 0.08 mm/ 300 mm
300
CB-0122
CB-0123
1.02
8.51
6.40
3.66
3.09
19.80
406
R9.00
R1.80
6.40
0.08
8.3
2.91
R8.01(IND)
R0.31(INT)
3.18
406
0.64
15.21
copper beryllium 0.13 mm/ 406 mm
copper beryllium 0.08 mm/ 406 mm
CB-0124
CB-0125 - CB-0132
copper beryllium 0.08 mm/ 228.96 mm
CB-0125
A
8.13
B
2.79
C
2.16
D
0.08
E
4.29
F
0.46
R
2.79
L
408
CB-0126
7.87
3.05
2.28
0.08
5.85
0.50
2.92
406
CB-0127
9.40
3.30
2.16
0.08
5.72
0.63
2.79
406
CB-0128
15.24
5.59
3.56
0.10
6.35
0.80
4.60
406
CB-0129
7.60
3.30
2.10
0.08
4.32
0.43
2.79
408
CB-0130
8.90
2.80
3.40
0.08
4.29
0.46
6.00
406
CB-0131
8.90
8.12
5.08
0.10
8.71
0.80
4.57
300
CB-0132
8.90
4.40
2.16
0.08
4.30
0.50
1.20
300 (mm)
MOQ : 300 pcs. from CB-0121 to CB-0132
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
76
SHIELDING

COPPER BERYLLIUM FINGER STRIPS
CB-0133
CB-0134
R0.59
3.20±0.3
406(APPROX)
2.40
R6.00
8.90
3.20
0.08
copper beryllium 0.08 mm/ 406 mm
0.46
4.75
copper beryllium 0.08 mm/ 408 mm
CB-0135
CB-0136
380
copper beryllium 0.05 mm/ 380 mm
copper beryllium 0.08 mm/ 363 mm
CB-0137
CB-0138
300
copper beryllium 0.08 mm/ 300 mm
copper beryllium 0.13 mm/ 500 mm
CB-0139
CB-0140
copper beryllium 0.13 mm/ 406 mm
copper beryllium 0.1 mm/ 500 mm
CB-0141
CB-0142
CB-0141
A
13.82
B
6.35
C
3.1
D
0.13
E
5.59
F
0.76
L
406
CB-0142
12.8
7.09
3.1
0.13
5.59
0.76
406
(mm)
77
MOQ : 300 pcs. from CB-0133 to CB-0142
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

COPPER BERYLLIUM FINGER STRIPS
CB-0143
CB-0144
copper beryllium 0.1 mm/ 408 mm
CB-0145
copper beryllium 0.08 mm/ 406 mm
CB-0146
425
copper beryllium 0.1 mm/ 425 mm
copper beryllium 0.1 mm/ 379.2 mm
CB-0147
CB-0148
406
copper beryllium 0.1 mm/ 406 mm
copper beryllium 0.1 mm/ 406 mm
CB-0149
CB-0150
300
copper beryllium 0.18 mm/ 500 mm
copper beryllium 0.15 mm/ 300 mm
CB-0151
CB-0152
300
300
copper beryllium 0.1 mm/ 300 mm
copper beryllium 0.08 mm/ 300 mm
MOQ : 300 pcs. from CB-0143 to CB-0152
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
78
SHIELDING

COPPER BERYLLIUM FINGER STRIPS
CB-0153
CB-0154
copper beryllium 0.15 mm/ 406 mm
copper beryllium 0.25 mm/ 406 mm
CB-0155
CB-0156
copper beryllium 0.08 mm/ 610 mm
copper beryllium 0.1 mm/ 480 mm
CB-0157
copper beryllium 0.13 mm/ 433.2 mm
CB-0158
CB-0161
CB-0158
A
8.9
B
4.26
C
6
D
0.08
E
4.32
F
0.46
G
2.2
H
1.5
L
500
CB-0159
19.8
6.4
13.5
0.13
8.51
1.02
3.8
3.6
610
CB-0160
17
7.9
13.5
0.1
8.51
1.02
3.8
3.6
409
CB-0161
28.7
10.4
19.8
*CB-0160 and CB-0161 are with adhesive tape
0.18
11.67
1.02
5.6
3.6
610
(mm)
MOQ : 300 pcs. from CB-0153 to CB-0161
79
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

COPPER BERYLLIUM FINGER STRIPS
CB-0162
CB-0165
CB-0162
A
9.7
B
3.1
C
3.38
D
0.08
E
4.32
F
0.46
G
3.7
H
1.5
L
406
CB-0163
6.4
2.0
2.24
0.08
4.32
0.46
2
1.5
565
CB-0164
19.3
5.8
3.38
0.1
8.72
0.81
6
2
610
CB-0165
13
CB-0165is with adhesive tape
3.6
3.58
0.08
5.79
0.56
4
1.5
381
(mm)
CB-0166
CB-0172
copper beryllium 0.06 mm/ 138.06 mm
copper beryllium 0.1 mm/ 406 mm
CB-0167
CB-0171
CB-0167
A
29.22
B
29.42
C
12.97
D
0.13
E
11.68
F
1.02
G
14.2
H
3.60
L
406
CB-0168
12.48
9.58
3.28
0.08
5.80
0.50
2.30
0.77
377.75
CB-0169
8.42
6.00
3.03
0.08
4.32
0.46
2.16
1.50
500
CB-0170
11,23
9.40
2.66
0.08
5.79
0.56
2.30
0.75
406
CB-0171
18.70
20.6
10.12
0.08
6.91
1.60
3.60 3.60 500 (mm)
Each shape is slightly different, please check drawing
CB-0170 with adhesive
MOQ : 300 pcs. from CB-0162 to CB-0172
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
80
SHIELDING

SHIELDING
MONOFILAMENT BRAIDED SLEEVING MFS-AG
Features
- Wiring and I/O cables associated with an electronic
device often act as an antenna or receiver that can couple
EMI sources to susceptible equipment nearby. Data
lines carrying broadband signals up to high frequency
ranges, also need to be shielded to minimise radiated
coupling.
- The MFS-AG is a highly flexible, lightweight braided
sleeve made of Polyamide 6.6 with a pure silver coating
that provides attenuation up to 54 dB. This braided sleeve
is easy to mount, selfadjusting to convex contours and
allows insertion of single wires at any place without cutting
the sleeve.
Technical Characteristics
Operating temperatures: -40°C to + 160°C ( -40°F to + 320°F )
Tensile strength:
approx. 2.1 Kg per single monofilament
Number of monofilaments:
depending on the diameter of the sleeve
Diameter of single monofilament: 0.27 ± 0.03 mm ( 0.01“ ± 0.001“ )
Minimum radius of the sleeve:
1 mm
Minimum surface coverage: > 75%
Colour:
metallic
Operating diameter range:
available from 1.5 mm to 115 mm Ø
Combustibility:
not selfextinguishing as empty sleeve***
Toxicity:
all materials are free of halogen, cadmium and
formaldehyde; non toxic
Surface resistivity: < 0.5 W /
Shielding effectiveness:
depending on diameter and frequency
- up to 54 dB as tested to MIL Std 1377 (DIN 47250 T6)
- up to 40 dB as tested to MIL Std 285
Requirements met:
flame extinguished before first measurement
point reached
VDE II B / VDE 0304, part 3 (5.70)
UL-94: 94 V-2, UL standard 94
Airbus Industry Technical Specification
ATS 1000.001, 4.1 and 4,2
***
In case of burning , the silver coating keeps a temperature higher than the self ignition temperature of the Polyamide 6.6
gases. Selfextinguishing cables inside the harness cool the silver down.
Shielding effect
81
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

SHIELDING
MONOFILAMENT BRAIDED SLEEVING MFS-AG
Part.No.
MFS-AG-3/4
MFS-AG-4/5
MFS-AG-6/8
MFS-AG-10/12
MFS-AG-14/16
MFS-AG-16/26
MFS-AG-18/25
MFS-AG-30
MFS-AG-40/45
MFS-AG-50/55
MFS-AG-60/65
MFS-AG- 80
MFS-AG-100
Dimension
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
from ø
1,5
3
5
7
8
16
18
24
32
32
32
32
50
for round objects
to ø
4
6
11
15
18
26
30
36
47
58
68
85
115
flat width
when delivered
4
5
9
11
17
20
28
30
45
51
57
61
95
number of
filaments
48
64
96
120
160
192
252
292
384
480
600
720
960
length of one
machine hank
over 600m
over 600m
over 600m
400-450m
300-340m
340-360m
300-340m
300-340m
300-340m
300-340m
260-270m
210-250m
140-160m
Dimensioned sketch for round objects
mm
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
82
SHIELDING

GENERAL TERMS OF DELIVERY AND PAYMENT
1. Scope
1.1 The following General Terms of Delivery and
Payment shall be applicable – provided nothing to
the contrary is stipulated in writing – to all of the
deliveries and other performance effected by us.
make up the delivery after the cessation of the
cause of the impediment. There shall be no claims
due to non-delivery or late delivery. This shall
also be applicable if above indicated circumstances
arise once the stipulated delivery period was
already exceeded.
default remains reserved.
6.3 The orderer can only set off the claims of
Kitagawa GmbH against undisputed counterclaims
or counter-claims which have been recognised
by a declaratory judgement.
83
1.2 Deviating General Terms of Business of the
orderer shall not bind us.
1.3 Amendments and/or supplements to the following
terms and to the additionally stipulated
agreements upon the conclusion of the contract
must be made in writing.
1.4 Details in catalogues and brochures as well as
in other documentation are non-binding insofar
as they were not expressly stipulated as binding.
2. Conclusion of the Contract
2.1 The offers of Kitagawa GmbH are made
without obligation.
2.2 A contract between Kitagawa GmbH and the
orderer shall only come into effect in accordance
with the contents of the written confirmation of
order on the part of Kitagawa GmbH or through
the delivery of the goods or the rendering of the
agreed performance by Kitagawa GmbH.
2.3 The orderer shall be bound to its order for
three weeks. Kitagawa GmbH reserves the right to
deviate from the orderer’s specifications in the
acceptance of the order if this is necessary for the
fulfillment of the order and is acceptable for the
contract Partner.
2.4 Kitagawa GmbH shall be entitled to effect an
alteration to the goods at any time without prior
notification insofar as this does not result in any
shortfall of the contractually stipulated characteristics
of the goods and the alteration is reasonable
for the orderer. The alteration of already delivered
contract products cannot be subsequently
demanded.
3. Delivery Terms
3.1 The delivery period of the goods shall be
determined in accordance with the written confirmation
of order of Kitagawa GmbH.
3.2 Indicated delivery periods shall run from the
dispatch of the written confirmation or order. lf the
orderer is obliged to effect advance performance,
then the delivery period shall commence with the
receipt of the contractual advance performance of
the orderer at Kitagawa GmbH.
3.3 If the orderer demands alterations to the contractually
stipulated performance after a written
confirmation of order has been effected, then
Kitagawa GmbH shall be entitled to effect a reasonable
extension to the delivery period if necessary.
3.4 In cases of force majeure, interventions by
sovereign powers, natural disasters, war, revolts,
strikes at its own company, at supply companies
or at carriers, Kitagawa GmbH shall be entitled to
3.5 If a promised delivery date is not met by
Kitagawa GmbH for justifiable reasons, then the
orderer shall be en-titled to set Kitagawa GmbH a
two-week subsequent period after the expiry of
the stipulated delivery period by means of registered
letter. The orderer shall be entitled to withdraw
from the agreement after the fruitless expiry
of the period. Claims for damages, insofar as is
legally permissible, as well as more extensive
rights shall be excluded, provided the delay in
delivery is neither due to intent nor gross negligence
on the part of Kitagawa GmbH. The burden
of proof that intent or gross negligence is not
applicable shall be borne by Kitagawa GmbH.
3.6 Kitagawa GmbH shall be entitled to effect part
deliveries.
4. Shipment and passing of risk
4.1 Kitagawa GmbH shall undertake the shipment
of the goods at the orderer’s expense. Kitagawa
GmbH shall select the forwarder/carrier to the
best of its knowledge, without, however, assuming
corresponding liability. Kitagawa GmbH
shall award the shipping order on the customary
terms in the sector in each case. Transport insurance
shall only be taken out at the orderer's
request and expense.
4.2 Risk shall pass when the goods leave the
warehouse or upon the surrender of the goods to
the forwarder/carrier.
4.3 Any transport damage which occurs must be
asserted by the orderer in due time to the forwarder/carrier
or its insurance company.
5. Prices
The prices are indicated in the respective confirmation
of order of Kitagawa GmbH and are
expressed net in EURO plus the statutory rate of
V.AT. exclusive of packing, freight, postage, delivery
charges etc.
6. Payment Terms
6.1 Insofar as no other payment terms are indicated
in the confirmation of order of Kitagawa
GmbH, the invoices are payable after the invoice
date within 30 days net without any discount.
Decisive for effecting payment on time is the
receipt of the payment at Kitagawa GmbH.
Cheques shall only be accepted in payment.
6.2 lf the orderer is a fully qualified merchant,
then it shall be in default upon the exceeding of
the due date without a separate warning.
Kitagawa GmbH shall be entitled to assert default
interest to the amount of 4 per cent over the respective
discount rate of Deutsche Bundesbank, at
least, however, to the amount of 6 per cent. The
assertion of a more extensive loss caused by
KE KITAGAWA
7. Warranty
7.1 Kitagawa warrants for the dura-tion of 6
months that the goods contain no material or
fabrication defects.
7.2 Warranty shall not be effected in the case of
improper utilisation, faulty installation, incorrect
operation etc. No warranty shall similarly be
effected for losses which arise through the operation
of the goods together with such appliances
whose compatibility has not been expressly confirmed
in writing by Kitagawa GmbH.
7.3 The orderer must raise objection to apparent
defects without delay in writing, at the latest,
however, within one week after the receipt of the
goods.
7.4 In the case of defects the warranty shall be
effected at the option of Kitagawa GmbH by subsequent
rectification or substitute delivery. If the
subsequent rectification also fails on the second
attempt or if the second sub-stitute delivery also
contains defects or if Kitagawa GmbH does not
meet its subsequent delivery or substitute delivery
obligation within a reasonable period, then the
orderer shall be enti-tled to a reduction of the
purchase price or rescission of the contract.
7.5 In the case of the violation of a contractual
obligation by Kitagawa GmbH or if a guaranteed
characteristic of the goods should be lacking, liability
shall be restricted to the loss which is to be
expected in accordance with the customary course
of events. More extensive claims on account of the
faulty nature of the goods shall be excluded. This
shall also be applicable to the reparation of consequential
losses and to the violation of ancillary
contractual obligations including culpa in contrahendo.
The prerequi-site for the afore mentioned
exclusions of liability is the proof by Kitagawa
GmbH that neither intent nor gross negligence
was applicable.
The afore mentioned exclusion of liability shall
also be applicable to claims in tort and in connection
with the initiation, conclusion and processing
of a contract, not, however, in the case of claims in
accordance with the Product Liability Act.
8. Retention of Title
8.1 Kitagawa GmbH shall retain title to all goods
until the payment in full of all receivables resulting
from the business relations with Kitagawa
GmbH. If the value of the collateral which is in
existence in favour of Kitagawa GmbH should
exceed the claims against the contract partner by
more than 20 per cent in total, then Kitagawa
GmbH shall be obliged to release collateral at the
request of the contract partner.
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)

GENERAL TERMS OF DELIVERY AND PAYMENT
8.2 The contract partner shall be enti-tled to resell
the goods subject to retention of title in customary
business transactions. The orderer shall not,
however, be entitled to pledge the goods subject
to retention of title or to assign them by way of
security. The orderer already now assigns all
claims to which it is entitled from a future sale of
the goods subject to retention of title against its
purchasers to Kitagawa GmbH by way of security.
Kitagawa GmbH hereby accepts this assignment.
8.3 In the case of the processing or reconstruction
of the goods subject to retention of title by the
orderer, this shall always be effected for Kitagawa
GmbH. If the goods subject to reten-tion of title
are processed with other articles which do not
belong to Kitagawa GmbH, then Kitagawa shall
acquire co-ownership to the new article in proportion
to the value of the goods subject to retention
of title to the other processed articles at the
time of processing. If the orderer sells the goods
subject to retention of title together with other
goods which do not belong to Kitagawa GmbH, or
after joining or processing, then the assignment
shall only be effected to the amount of the outstanding
invoice sum of the respective goods subject
to retention of title.
8.4 The orderer shall be entitled to collect the
assigned receivables in its own name. Kitagawa
GmbH shall, however, be entitled to revoke this
collection authority at any time, especially in the
case of default in payment by the orderer. In the
case of revocation the orderer shall be obliged to
provide Kitagawa GmbH with or to surrender to it
all necessary information and documentation for
the asser-tion of the assigned receivables and to
disclose the assignments to its purchasers. In the
case of default in payment by the orderer
Kitagawa GmbH shall be entitled to notify the
orderer's purchasers of the assignment.
8.5 The orderer shall be obliged to provide
Kitagawa GmbH with information at any time on
the where-abouts of the goods subject to retention
of title and on the receivables
arising from their resale. The orderer shall be
obliged to inform Kitagawa GmbH in writing of a
seizure by a third party of the goods subject to
retention of title or of the receivables assigned to
Kitagawa GmbH and it shall be obliged to draw
the third party’s attention to the rights of
Kitagawa GmbH. The orderer shall furthermore be
obliged to support Kitagawa GmbH upon the
assertion and enforce-ment of its rights against
this third party, especially at its expense to lodge
the necessary immediate remedies/appeals in
order to safeguard the rights of Kitagawa GmbH.
8.6 In the case of default in payment on the part
of the orderer Kitagawa GmbH shall be entitled to
take back the goods subject to retention of title.
The orderer shall accordingly be obliged to surrender
these goods. The taking back of the goods
subject to retention of title does not constitute a
withdrawal from the contract, unless Kitagawa
GmbH expressly states such a withdrawal in writing.
8.7 The orderer shall be obliged to treat the delivered
goods subject to retention of title with care.
lt shall especially be obliged to take out adequate
insurance cover for the goods subject to retention
of title at its own expense against loss or damage
through fire, water, burglary or theft. The orderer
hereby assigns its corresponding insurance claims
to Kitagawa GmbH. Kitagawa GmbH hereby
accepts this assignment and states the reassignment
to the orderer with the proviso that this
shall become effective if and as soon as the retention
of title has expired.
9. Final Provisions
9.1 The orderer shall not be entitled to assign
rights and obligations to third parties arising from
the contract concluded with Kitagawa GmbH
without the prior agreement of Kitagawa GmbH.
9.2 The contractual relations between the contracting
parties shall be subject to the Law of the
Federal Republic of Germany. The provisions of
the Convention on Contracts of the International
Sale of Goods (CISG, Vienna Convention) shall not
apply to the contract concluded with the orderer.
9.3 Place of jurisdiction for all disputes and types
of proceedings arising from or in connection with
the contractual relations between the parties
shall be Darmstadt, Federal Republic of Germany,
provided the orderer is a fully qualified merchant.
9.4 Kitagawa GmbH shall be entitled to store and
to use the personal data to which it has received
access from the business relations with the orderer
under the terms of the German Data
Protection Act for its own business purposes.
9.5 If a provision of these General Terms of
Business or of the contract concluded with the
orderer should be or become ineffective, then this
shall not affect the effectiveness of the remaining
provisions of these General Terms of Business or
of the concluded contract.
KE KITAGAWA GmbH
KITAGAWA GmbH · Elbinger Straße 3-5
D-63110 Rodgau-Jügesheim
FR-Germany
Telefon 0 61 06/85 24-0
Telefax 0 61 06/85 24-30(31)
Notice:
The specifications provided in this catalogue are
believed to be accurate and reliable. Kitagawa
GmbH reserves the right to make changes to
specifications to improve manufacturing process,
performance and reliability.
This catalogue is intended for representation only
and is not to form any part of any order.
Engineering specifications are available upon
request.
Any information/specification supplied Kitagawa
GmbH is based upon Kitagawa Industries laboratory
test data and is believed to be reliable. It is
recommended that our products are tested by the
customer to ensure suitability for the intended
application.
If any Kitagawa product is to be used in a life
threatening application(Such areas as Medical,
Automotive and Aerospace etc). The application
must be discussed with the company and written
approval must be obtained.
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)
84

FOR YOUR PERSONAL NOTES
KE KITAGAWA
Elbinger Straße 3-5 · D-63110 Rodgau-Jügesheim · Germany · Telefon 0 61 06/85 24 - 0 · Telefax 0 61 06/85 24-30 (31)