Installation Manual for SMX Modules - OEM Automatic AB
Installation Manual for SMX Modules - OEM Automatic AB Installation Manual for SMX Modules - OEM Automatic AB
Installation Manual Alarm code A 3177 / A 3178 Alarm message Cause Remedy Faulty 24 V signal on DI10 No permanent 24 V voltage applied to this input • Check the voltage on the digital input! • Check wiring • Check whether Pulse1 or Pulse2 is applied Alarm code A 3179 / A 3180 Alarm message Cause Remedy Faulty 24 V signal on DI11 No permanent 24 V voltage applied to this input • Check the voltage on the digital input! • Check wiring • Check whether Pulse1 or Pulse2 is applied Alarm code A 3181 / A 3182 Alarm message Cause Remedy Faulty 24 V signal on DI12 No permanent 24 V voltage applied to this input • Check the voltage on the digital input! • Check wiring • Check whether Pulse1 or Pulse2 is applied Alarm code A 3183 / A 3184 Alarm message Cause Remedy Faulty 24 V signal on DI13 No permanent 24 V voltage applied to this input • Check the voltage on the digital input! • Check wiring • Check whether Pulse1 or Pulse2 is applied Alarm code A 3185 / A 3186 Alarm message Cause Remedy Faulty 24 V signal on DI14 No permanent 24 V voltage applied to this input • Check the voltage on the digital input! • Check wiring • Check whether Pulse1 or Pulse2 is applied Alarm code A 3197 / A 3198 Alarm message Faulty OSSD input test Cause OSSD test faulty Remedy • 24 V check the input voltage on all OSSD inputs Alarm code A 3209 / A 3210 Fault message Cause Remedy Encoder supply voltage X31 faulty. • Encoder supply voltage does not comply with configured threshold • Component fault in module • Check configuration! • Check encoder supply voltage • Switch device off/on. HB-37350-810-01-10E-EN SMX installation manual.doc Page 68 of 68
Installation Manual Alarm code A 3213 / A 3214 Fault message Cause Remedy Encoder supply voltage X32 faulty. • Encoder supply voltage does not comply with configured threshold • Component fault in module • Check configuration! • Check encoder supply voltage • Switch device off/on. Alarm code A 3225 / A 3226 Fault message Cause Remedy Deviation Ain1 to AIn2 too big • Different voltages on both inputs • configured threshold too low • Check voltages on Ain1! • Check configuration of threshold/input filter • Switch device off/on. Alarm code A 3227 / A 3228 Fault message Cause Remedy Deviation Ain3 to AIn4 too big • Different voltages on both inputs • configured threshold too low • Check voltages on Ain1! • Check configuration of threshold/input filter • Switch device off/on. Alarm code A 3229 / A 3230 Fault message Plausibility test for encoder voltage faulty Cause • Encoder voltage value • Check encoder voltage supply Remedy • Check wiring of encoder voltage supply Alarm code A 3231 / A 3232 Fault message Plausibility test for analog inputs faulty Cause • Fault in analog input signal • Check connection of analog inputs Remedy • Analog input voltage out of range Alarm code A 3233 / A 3234 Fault message Open-circuit monitoring AIN1 has triggered Cause • Open-circuit monitoring is activated • Check configuration of activation/sensor Remedy • Check sensor connection Alarm code A 3235 / A 3236 Fault message Open-circuit monitoring AIN2 has triggered Cause • Open-circuit monitoring is activated • Check configuration of activation/sensor Remedy • Check sensor connection HB-37350-810-01-10E-EN SMX installation manual.doc Page 69 of 69
- Page 17 and 18: Installation Manual 4.4 External 24
- Page 19 and 20: Installation Manual 4.6 Connection
- Page 21 and 22: Installation Manual Note: • In th
- Page 23 and 24: Installation Manual 2. Single-chann
- Page 25 and 26: Installation Manual 4.8 Connection
- Page 27 and 28: Installation Manual Attention: The
- Page 29 and 30: Installation Manual 6.2 Connection
- Page 31 and 32: Installation Manual 6.4 Connection
- Page 33 and 34: Installation Manual 8 Sensor type A
- Page 35 and 36: Installation Manual For application
- Page 37 and 38: Installation Manual The test functi
- Page 39 and 40: Installation Manual 10.1.2 Single-p
- Page 41 and 42: Installation Manual 10.1.4 Single-p
- Page 43 and 44: Installation Manual 10.1.6 Wiring o
- Page 45 and 46: Installation Manual 10.2.2 Wiring t
- Page 47 and 48: Installation Manual Response times
- Page 49 and 50: Installation Manual 11 Start-up 11.
- Page 51 and 52: Installation Manual 11.4 Terminal a
- Page 53 and 54: Installation Manual 12 Safety relat
- Page 55 and 56: Installation Manual 14 Technical da
- Page 57 and 58: Installation Manual 15.2 Alarm list
- Page 59 and 60: Installation Manual Alarm code A 30
- Page 61 and 62: Installation Manual Alarm code A 30
- Page 63 and 64: Installation Manual Alarm code A 31
- Page 65 and 66: Installation Manual Alarm code A 31
- Page 67: Installation Manual Alarm code A 31
- Page 71 and 72: Installation Manual Alarm code A 33
- Page 73 and 74: Installation Manual Alarm code A 35
- Page 75 and 76: Installation Manual 15.3 Fatal Erro
- Page 77 and 78: Installation Manual Fatal Error Cod
- Page 79 and 80: Installation Manual Fatal Error Cod
- Page 81 and 82: Installation Manual Fatal Error Cod
- Page 83 and 84: Installation Manual Fatal Error Cod
- Page 85 and 86: Installation Manual Fatal Error Cod
- Page 87 and 88: Installation Manual 16 Encoder type
- Page 89 and 90: Installation Manual 17 Switch types
- Page 91 and 92: Installation Manual Type Graphic sy
- Page 93 and 94: Installation Manual 10 eSwitch_3oT
- Page 95 and 96: Installation Manual eTwoHand_2s LD
- Page 97 and 98: Installation Manual Two-hand button
<strong>Installation</strong> <strong>Manual</strong><br />
Alarm code A 3213 / A 3214<br />
Fault message<br />
Cause<br />
Remedy<br />
Encoder supply voltage X32 faulty.<br />
• Encoder supply voltage does not comply with configured<br />
threshold<br />
• Component fault in module<br />
• Check configuration!<br />
• Check encoder supply voltage<br />
• Switch device off/on.<br />
Alarm code A 3225 / A 3226<br />
Fault message<br />
Cause<br />
Remedy<br />
Deviation Ain1 to AIn2 too big<br />
• Different voltages on both inputs<br />
• configured threshold too low<br />
• Check voltages on Ain1!<br />
• Check configuration of threshold/input filter<br />
• Switch device off/on.<br />
Alarm code A 3227 / A 3228<br />
Fault message<br />
Cause<br />
Remedy<br />
Deviation Ain3 to AIn4 too big<br />
• Different voltages on both inputs<br />
• configured threshold too low<br />
• Check voltages on Ain1!<br />
• Check configuration of threshold/input filter<br />
• Switch device off/on.<br />
Alarm code A 3229 / A 3230<br />
Fault message Plausibility test <strong>for</strong> encoder voltage faulty<br />
Cause • Encoder voltage value<br />
• Check encoder voltage supply<br />
Remedy<br />
• Check wiring of encoder voltage supply<br />
Alarm code A 3231 / A 3232<br />
Fault message Plausibility test <strong>for</strong> analog inputs faulty<br />
Cause • Fault in analog input signal<br />
• Check connection of analog inputs<br />
Remedy<br />
• Analog input voltage out of range<br />
Alarm code A 3233 / A 3234<br />
Fault message Open-circuit monitoring AIN1 has triggered<br />
Cause • Open-circuit monitoring is activated<br />
• Check configuration of activation/sensor<br />
Remedy<br />
• Check sensor connection<br />
Alarm code A 3235 / A 3236<br />
Fault message Open-circuit monitoring AIN2 has triggered<br />
Cause • Open-circuit monitoring is activated<br />
• Check configuration of activation/sensor<br />
Remedy<br />
• Check sensor connection<br />
HB-37350-810-01-10E-EN <strong>SMX</strong> installation manual.doc Page 69 of 69