Installation Manual for SMX Modules - OEM Automatic AB
Installation Manual for SMX Modules - OEM Automatic AB Installation Manual for SMX Modules - OEM Automatic AB
Installation Manual 10.1.5 Two-channel switching relay output with external monitoring – Group feedback For safety related applications from Pl d acc. to EN ISO 13849-1 two relays on the SMX module and two external power contactors are used. X22 K1 K2 DI1 DI2 DI3 DI4 DI13 DI14 P1 P2 X14 X12 L+ L- Fig.: Two-channel switching relay output with external monitoring – group feedback The two external monitoring contacts are switched in series, supplied by the clock signal P1 and read in from DI1 (configured as EMU-input). In case of higher demands one must consider that at least 1 switching process must take place every 24 hours. HB-37350-810-01-10E-EN SMX installation manual.doc Page 42 of 42
Installation Manual 10.1.6 Wiring of an auxiliary output Both semi-conductor outputs implemented on the SMX module can be wired for functional applications. These outputs are not pulsing. X13 O.1 O.2 L+ Fig.: Wiring of an auxiliary output L- Applications with auxiliary outputs are not accepted for safety related applications! 10.2 Expansion module EAA1 … EAA10 Architecture Performance Level Comment Static single-channel PL c - Fault detection or fault reaction acc. to cat. 2 Static two-channel PL e - Different group - Same group - Time-shifted triggering on PLC level Static two-channel PL d - Application instruction with specified time - Fault approach short-circuit on both outputs Dynamically single-channel PL e Dynamically two-channel PL e HB-37350-810-01-10E-EN SMX installation manual.doc Page 43 of 43
- Page 1 and 2: Installation Manual Installation Ma
- Page 3 and 4: Installation Manual 9 SAFETY RELEVA
- Page 5 and 6: Installation Manual 1.2 Co-valid do
- Page 7 and 8: Installation Manual 2 Safety regula
- Page 9 and 10: Installation Manual 3.1.2 SMX11 Typ
- Page 11 and 12: Installation Manual 3.1.4 SMX12A Ty
- Page 13 and 14: Installation Manual 3.1.6 Type plat
- Page 15 and 16: Installation Manual 4.2 Installatio
- Page 17 and 18: Installation Manual 4.4 External 24
- Page 19 and 20: Installation Manual 4.6 Connection
- Page 21 and 22: Installation Manual Note: • In th
- Page 23 and 24: Installation Manual 2. Single-chann
- Page 25 and 26: Installation Manual 4.8 Connection
- Page 27 and 28: Installation Manual Attention: The
- Page 29 and 30: Installation Manual 6.2 Connection
- Page 31 and 32: Installation Manual 6.4 Connection
- Page 33 and 34: Installation Manual 8 Sensor type A
- Page 35 and 36: Installation Manual For application
- Page 37 and 38: Installation Manual The test functi
- Page 39 and 40: Installation Manual 10.1.2 Single-p
- Page 41: Installation Manual 10.1.4 Single-p
- Page 45 and 46: Installation Manual 10.2.2 Wiring t
- Page 47 and 48: Installation Manual Response times
- Page 49 and 50: Installation Manual 11 Start-up 11.
- Page 51 and 52: Installation Manual 11.4 Terminal a
- Page 53 and 54: Installation Manual 12 Safety relat
- Page 55 and 56: Installation Manual 14 Technical da
- Page 57 and 58: Installation Manual 15.2 Alarm list
- Page 59 and 60: Installation Manual Alarm code A 30
- Page 61 and 62: Installation Manual Alarm code A 30
- Page 63 and 64: Installation Manual Alarm code A 31
- Page 65 and 66: Installation Manual Alarm code A 31
- Page 67 and 68: Installation Manual Alarm code A 31
- Page 69 and 70: Installation Manual Alarm code A 32
- Page 71 and 72: Installation Manual Alarm code A 33
- Page 73 and 74: Installation Manual Alarm code A 35
- Page 75 and 76: Installation Manual 15.3 Fatal Erro
- Page 77 and 78: Installation Manual Fatal Error Cod
- Page 79 and 80: Installation Manual Fatal Error Cod
- Page 81 and 82: Installation Manual Fatal Error Cod
- Page 83 and 84: Installation Manual Fatal Error Cod
- Page 85 and 86: Installation Manual Fatal Error Cod
- Page 87 and 88: Installation Manual 16 Encoder type
- Page 89 and 90: Installation Manual 17 Switch types
- Page 91 and 92: Installation Manual Type Graphic sy
<strong>Installation</strong> <strong>Manual</strong><br />
10.1.6 Wiring of an auxiliary output<br />
Both semi-conductor outputs implemented on the <strong>SMX</strong> module can be wired <strong>for</strong> functional<br />
applications. These outputs are not pulsing.<br />
X13<br />
O.1<br />
O.2<br />
L+<br />
Fig.: Wiring of an auxiliary output<br />
L-<br />
Applications with auxiliary outputs are not accepted <strong>for</strong> safety related applications!<br />
10.2 Expansion module EAA1 … EAA10<br />
Architecture Per<strong>for</strong>mance Level Comment<br />
Static single-channel PL c<br />
- Fault detection or fault reaction acc. to<br />
cat. 2<br />
Static two-channel PL e - Different group<br />
- Same group<br />
- Time-shifted triggering on PLC level<br />
Static two-channel PL d<br />
- Application instruction with specified time<br />
- Fault approach short-circuit on both<br />
outputs<br />
Dynamically<br />
single-channel<br />
PL e<br />
Dynamically<br />
two-channel<br />
PL e<br />
HB-37350-810-01-10E-EN <strong>SMX</strong> installation manual.doc Page 43 of 43