TOYOTA Intelligent Tester User Manual - Obd2be.com
TOYOTA Intelligent Tester User Manual - Obd2be.com TOYOTA Intelligent Tester User Manual - Obd2be.com
2 Basic Operations Ending CAUTION If the power to the Intelligent Tester II is switched OFF during an active test, the actuator may remain in the drive state. Always end the active test before switching the power OFF. 1. Turn the vehicle ignition switch OFF. 2. Press the Intelligent Tester II power switch to turn the power OFF. 3. Disconnect the datalink cable from the vehicle side datalink connector (DLC3). T00049E CAUTION When disconnecting the datalink cable from vehicle side datalink connector (DLC 3), gently pull it straight out of the connector. Pulling the cable at a slant can break the connector pins. When pulling the cable out, hold it by the connector section, and never by the cord section. Pulling on the cord section can break the lines in the cable. - 23 - http://www.obd2be.com/
2 Basic Operations Screen Configuration The screen configuration for the Intelligent Tester II is as follows. Menu Bar Title Bar Infomation display area Function buttons Main Menu Buttons Screen Configuration T00050E NOTE The Intelligent Tester II display is a touch panel, so use your fingers to operate it. When a menu bar or button item is displayed in gray, this indicates that the item is disabled. Main Menu Buttons The main menu buttons are composed of frequently used functions. These functions can be selected from the menu bars, but the main menu buttons enable these functions to be started at one touch. Main Menu Buttons T00051E ACTIVE KEY DTC Starts the DTC check. Freeze frame data can also be checked with a DTC check. Data List Starts the data list. Snapshots can also be recorded with the data list. View Switches the data list display format. Active Test Starts an active test. Utility Starts the utility. - 24 - http://www.obd2be.com/
- Page 1 and 2: http://www.obd2be.com/
- Page 3 and 4: SOFTWARE as a Component of the DEVI
- Page 5 and 6: Preface Preface Thank you for purch
- Page 7 and 8: For safe usage CAUTION Do not leave
- Page 9 and 10: Table of contents 4 Diagnostics Fun
- Page 11 and 12: 1 Before Use 1 Before Use Product C
- Page 13 and 14: 1 Before Use AC / DC Power Supply P
- Page 15 and 16: 1 Before Use Confirmation of the ma
- Page 17 and 18: 1 Before Use Names of the Parts The
- Page 19 and 20: 1 Before Use How to Use the Stand T
- Page 21 and 22: 1 Before Use CAUTION Do not use dev
- Page 23 and 24: 1 Before Use Connection This sectio
- Page 25 and 26: 1 Before Use Inserting a CF Card Th
- Page 27 and 28: 1 Before Use Connecting the Probes
- Page 29 and 30: 2 Basic Operations http://www.obd2b
- Page 31: 2 Basic Operations After the openin
- Page 35 and 36: 2 Basic Operations Menu Bar Five me
- Page 37 and 38: 2 Basic Operations [System] menu To
- Page 39 and 40: 2 Basic Operations Scroll bar opera
- Page 41 and 42: 2 Basic Operations In Case of Error
- Page 43 and 44: 3 Default Settings http://www.obd2b
- Page 45 and 46: 3 Default Settings Supplementary Fu
- Page 47 and 48: 3 Default Settings Unit Conversion
- Page 49 and 50: 3 Default Settings Touch Panel Comp
- Page 51 and 52: 4 Diagnostics Functions http://www.
- Page 53 and 54: 4 Diagnostics Functions NOTE If a m
- Page 55 and 56: 4 Diagnostics Functions DTC Check D
- Page 57 and 58: 4 Diagnostics Functions If the stor
- Page 59 and 60: 4 Diagnostics Functions Freeze Fram
- Page 61 and 62: 4 Diagnostics Functions ACTIVE KEY
- Page 63 and 64: 4 Diagnostics Functions Data List V
- Page 65 and 66: 4 Diagnostics Functions Display Swi
- Page 67 and 68: 4 Diagnostics Functions Data List 1
- Page 69 and 70: 4 Diagnostics Functions Meter 1 Met
- Page 71 and 72: 4 Diagnostics Functions Line Graph
- Page 73 and 74: 4 Diagnostics Functions Bar Graph T
- Page 75 and 76: 4 Diagnostics Functions "Vehicle mo
- Page 77 and 78: 4 Diagnostics Functions Snapshot op
- Page 79 and 80: 4 Diagnostics Functions Parameter t
- Page 81 and 82: 4 Diagnostics Functions ACTIVE KEY
2 Basic Operations<br />
Screen Configuration<br />
The screen configuration for the <strong>Intelligent</strong> <strong>Tester</strong> II is as follows.<br />
Menu Bar<br />
Title Bar<br />
Infomation display area<br />
Function buttons<br />
Main Menu Buttons<br />
Screen Configuration<br />
T00050E<br />
NOTE<br />
The <strong>Intelligent</strong> <strong>Tester</strong> II display is a touch panel, so use your fingers to operate it.<br />
When a menu bar or button item is displayed in gray, this indicates that the item is disabled.<br />
Main Menu Buttons<br />
The main menu buttons are <strong>com</strong>posed of frequently used functions.<br />
These functions can be selected from the menu bars, but the main menu buttons enable these functions to be started at one<br />
touch.<br />
Main Menu Buttons<br />
T00051E<br />
ACTIVE KEY<br />
DTC<br />
Starts the DTC check. Freeze frame data can also be checked with a DTC check.<br />
Data List<br />
Starts the data list. Snapshots can also be recorded with the data list.<br />
View<br />
Switches the data list display format.<br />
Active Test<br />
Starts an active test.<br />
Utility<br />
Starts the utility.<br />
- 24 -<br />
http://www.obd2be.<strong>com</strong>/