TOYOTA Intelligent Tester User Manual - Obd2be.com
TOYOTA Intelligent Tester User Manual - Obd2be.com TOYOTA Intelligent Tester User Manual - Obd2be.com
1 Before Use Charging The main unit of the Intelligent Tester II has a special internal rechargeable battery (lithium ion battery). This battery is not charged when the Intelligent Tester II is shipped from the factory, so be sure to charge the battery before using the tester. NOTE There is no need to turn OFF the power switch on the Intelligent Tester II while charging. The Intelligent Tester II can be charged with the power ON or OFF. It takes approximately five hours to fully charge the battery from a completely discharged state, regardless of whether the power switch is ON or OFF. 1. Connect the AC/DC adapter DC plug to the AC/DC adapter connector of the Intelligent Tester II. 2. Plug the AC/DC adapter power plug into an electrical socket. Charging starts and the battery indicator on the Intelligent Tester II lights up red. Charging is complete when the battery indicator changes from red to green. 3. Disconnect the AC/DC adapter DC plug from the AC/DC adapter connector of the Intelligent Tester II. 4. Unplug the AC/DC adapter power plug from the electrical socket. T00036E - 11 - http://www.obd2be.com/
1 Before Use CAUTION Do not use devices other than the optional AC/DC adapter when charging the battery of the Intelligent Tester II. Using other adapters may prevent battery charging, and cause heating of and damage to the charger. Do not leave the AC/DC adapter plugged into the electrical socket after charging is complete. Dust can build up between the socket and the plug and cause tracking and fire. If the battery is charged while outside the usage temperature range, the battery indicator flashes. Continued charging in this condition could damage the equipment, so discontinue charging. Do not connect the AC/DC adapter to the Intelligent Tester II, when using the oscilloscope function. NOTE The Intelligent Tester II can be connected to the vehicle with the datalink cable to run off the vehicle battery when the tester internal battery is not charged. In this state, the Intelligent Tester II internal battery will charge using the vehicle power, so take care not to run down the vehicle battery. When using the Intelligent Tester II without connecting it to the vehicle (for example when using it as an oscilloscope), monitor the amount of power remaining in the battery and charge it with the AC/DC adapter when it runs low. The onboard/offboard check screen can be used to check the amount of power remaining in the battery. Reference: Page 25 Battery icon (Chapter 2. Basic Operations/Screen Configuration/Title Bar) It is normal for the main unit of the Intelligent Tester II to heat up during charging. The Intelligent Tester II may be left connected to the AC/DC adapter when the charging is complete. - 12 - http://www.obd2be.com/
- Page 1 and 2: http://www.obd2be.com/
- Page 3 and 4: SOFTWARE as a Component of the DEVI
- Page 5 and 6: Preface Preface Thank you for purch
- Page 7 and 8: For safe usage CAUTION Do not leave
- Page 9 and 10: Table of contents 4 Diagnostics Fun
- Page 11 and 12: 1 Before Use 1 Before Use Product C
- Page 13 and 14: 1 Before Use AC / DC Power Supply P
- Page 15 and 16: 1 Before Use Confirmation of the ma
- Page 17 and 18: 1 Before Use Names of the Parts The
- Page 19: 1 Before Use How to Use the Stand T
- Page 23 and 24: 1 Before Use Connection This sectio
- Page 25 and 26: 1 Before Use Inserting a CF Card Th
- Page 27 and 28: 1 Before Use Connecting the Probes
- Page 29 and 30: 2 Basic Operations http://www.obd2b
- Page 31 and 32: 2 Basic Operations After the openin
- Page 33 and 34: 2 Basic Operations Screen Configura
- Page 35 and 36: 2 Basic Operations Menu Bar Five me
- Page 37 and 38: 2 Basic Operations [System] menu To
- Page 39 and 40: 2 Basic Operations Scroll bar opera
- Page 41 and 42: 2 Basic Operations In Case of Error
- Page 43 and 44: 3 Default Settings http://www.obd2b
- Page 45 and 46: 3 Default Settings Supplementary Fu
- Page 47 and 48: 3 Default Settings Unit Conversion
- Page 49 and 50: 3 Default Settings Touch Panel Comp
- Page 51 and 52: 4 Diagnostics Functions http://www.
- Page 53 and 54: 4 Diagnostics Functions NOTE If a m
- Page 55 and 56: 4 Diagnostics Functions DTC Check D
- Page 57 and 58: 4 Diagnostics Functions If the stor
- Page 59 and 60: 4 Diagnostics Functions Freeze Fram
- Page 61 and 62: 4 Diagnostics Functions ACTIVE KEY
- Page 63 and 64: 4 Diagnostics Functions Data List V
- Page 65 and 66: 4 Diagnostics Functions Display Swi
- Page 67 and 68: 4 Diagnostics Functions Data List 1
- Page 69 and 70: 4 Diagnostics Functions Meter 1 Met
1 Before Use<br />
CAUTION<br />
Do not use devices other than the optional AC/DC adapter when charging the battery of the <strong>Intelligent</strong><br />
<strong>Tester</strong> II.<br />
Using other adapters may prevent battery charging, and cause heating of and damage to the charger.<br />
Do not leave the AC/DC adapter plugged into the electrical socket after charging is <strong>com</strong>plete.<br />
Dust can build up between the socket and the plug and cause tracking and fire.<br />
If the battery is charged while outside the usage temperature range, the battery indicator flashes.<br />
Continued charging in this condition could damage the equipment, so discontinue charging.<br />
Do not connect the AC/DC adapter to the <strong>Intelligent</strong> <strong>Tester</strong> II, when using the oscilloscope function.<br />
NOTE<br />
The <strong>Intelligent</strong> <strong>Tester</strong> II can be connected to the vehicle with the datalink cable to run off the vehicle<br />
battery when the tester internal battery is not charged.<br />
In this state, the <strong>Intelligent</strong> <strong>Tester</strong> II internal battery will charge using the vehicle power, so take care not to<br />
run down the vehicle battery.<br />
When using the <strong>Intelligent</strong> <strong>Tester</strong> II without connecting it to the vehicle (for example when using it as an<br />
oscilloscope), monitor the amount of power remaining in the battery and charge it with the AC/DC adapter<br />
when it runs low.<br />
The onboard/offboard check screen can be used to check the amount of power remaining in the battery.<br />
Reference: Page 25 Battery icon (Chapter 2. Basic Operations/Screen Configuration/Title Bar)<br />
It is normal for the main unit of the <strong>Intelligent</strong> <strong>Tester</strong> II to heat up during charging.<br />
The <strong>Intelligent</strong> <strong>Tester</strong> II may be left connected to the AC/DC adapter when the charging is <strong>com</strong>plete.<br />
- 12 -<br />
http://www.obd2be.<strong>com</strong>/