ANSYS FLUENT Tutorial Guide

More documents

Recommendations

Info

Copyright and Trademark Information © 2011 SAS IP, Inc. All rights reserved. Unauthorized use, distribution or duplication is prohibited. ANSYS, ANSYS Workbench, Ansoft, AUTODYN, EKM, Engineering Knowledge Manager, CFX, FLUENT, HFSS and any and all ANSYS, Inc. brand, product, service and feature names, logos and slogans are registered trademarks or trademarks of ANSYS, Inc. or its subsidiaries in the United States or other countries. ICEM CFD is a trademark used by ANSYS, Inc. under license. CFX is a trademark of Sony Corporation in Japan. All other brand, product, service and feature names or trademarks are the property of their respective owners. Disclaimer Notice THIS ANSYS SOFTWARE PRODUCT AND PROGRAM DOCUMENTATION INCLUDE TRADE SECRETS AND ARE CONFID- ENTIAL AND PROPRIETARY PRODUCTS OF ANSYS, INC., ITS SUBSIDIARIES, OR LICENSORS. The software products and documentation are furnished by ANSYS, Inc., its subsidiaries, or affiliates under a software license agreement that contains provisions concerning non-disclosure, copying, length and nature of use, compliance with exporting laws, warranties, disclaimers, limitations of liability, and remedies, and other provisions. The software products and documentation may be used, disclosed, transferred, or copied only in accordance with the terms and conditions of that software license agreement. ANSYS, Inc. is certified to ISO 9001:2008. U.S. Government Rights For U.S. Government users, except as specifically granted by the ANSYS, Inc. software license agreement, the use, duplication, or disclosure by the United States Government is subject to restrictions stated in the ANSYS, Inc. software license agreement and FAR 12.212 (for non-DOD licenses). Third-Party Software See the legal information in the product help files for the complete Legal Notice for ANSYS proprietary software and third-party software. If you are unable to access the Legal Notice, please contact ANSYS, Inc. Published in the U.S.A.
Table of Contents Using This Manual ...................................................................................................................................... xiii 1. What’s In This Manual ........................................................................................................................ xiii 2. The Contents of the FLUENT Manuals ................................................................................................ xiii 3. Where to Find the Files Used in the Tutorials ...................................................................................... xiv 4. How To Use This Manual .................................................................................................................... xiv 4.1. For the Beginner ....................................................................................................................... xv 4.2. For the Experienced User ........................................................................................................... xv 5.Typographical Conventions Used In This Manual ................................................................................. xv 1. Introduction to Using ANSYS FLUENT in ANSYS Workbench: Fluid Flow and Heat Transfer in a Mixing Elbow .......................................................................................................................................................... 1 1.1. Introduction ..................................................................................................................................... 1 1.2. Prerequisites ..................................................................................................................................... 1 1.3. Problem Description ......................................................................................................................... 2 1.4. Setup and Solution ........................................................................................................................... 2 1.4.1. Preparation .............................................................................................................................. 3 1.4.2. Step 1: Creating a FLUENT Fluid Flow Analysis System in ANSYS Workbench .............................. 4 1.4.3. Step 2: Creating the Geometry in ANSYS DesignModeler ........................................................... 8 1.4.4. Step 3: Meshing the Geometry in the ANSYS Meshing Application ........................................... 19 1.4.5. Step 4: Setting Up the CFD Simulation in ANSYS FLUENT ......................................................... 26 1.4.6. Step 5: Displaying Results in ANSYS FLUENT and CFD-Post ....................................................... 50 1.4.7. Step 6: Duplicating the FLUENT-Based Fluid Flow Analysis System ........................................... 60 1.4.8. Step 7: Changing the Geometry in ANSYS DesignModeler ....................................................... 61 1.4.9. Step 8: Updating the Mesh in the ANSYS Meshing Application ................................................. 64 1.4.10. Step 9: Calculating a New Solution in ANSYS FLUENT ............................................................. 67 1.4.11. Step 10: Comparing the Results of Both Systems in CFD-Post ................................................. 69 1.4.12. Step 11: Summary ................................................................................................................ 74 2. Parametric Analysis in ANSYS Workbench Using ANSYS FLUENT ........................................................ 77 2.1. Introduction ................................................................................................................................... 77 2.2. Prerequisites ................................................................................................................................... 78 2.3. Problem Description ....................................................................................................................... 78 2.4. Setup and Solution ......................................................................................................................... 82 2.4.1. Preparation ............................................................................................................................ 83 2.4.2. Step 1: Adding Constraints to ANSYS DesignModeler Parameters in ANSYS Workbench ........... 83 2.4.3. Step 2: Setting Up the CFD Simulation in ANSYS FLUENT ......................................................... 92 2.4.4. Step 3: Defining Input and Output Parameters in ANSYS FLUENT and Running the Simulation ................................................................................................................................................ 96 2.4.5. Step 4: Postprocessing in ANSYS CFD-Post ............................................................................ 108 2.4.6. Step 5: Creating Additional Design Points in ANSYS Workbench ............................................. 122 2.4.7. Step 6: Postprocessing the New Design Points in CFD-Post .................................................... 124 2.4.8. Step 7: Summary .................................................................................................................. 130 3. Introduction to Using ANSYS FLUENT: Fluid Flow and Heat Transfer in a Mixing Elbow .................... 131 3.1. Introduction ................................................................................................................................. 131 3.2. Prerequisites ................................................................................................................................. 131 3.3. Problem Description ..................................................................................................................... 131 3.4. Setup and Solution ....................................................................................................................... 132 3.4.1. Preparation .......................................................................................................................... 133 3.4.2. Step 1: Launching ANSYS FLUENT ......................................................................................... 133 3.4.3. Step 2: Mesh ......................................................................................................................... 136 3.4.4. Step 3: General Settings ........................................................................................................ 140 3.4.5. Step 4: Models ...................................................................................................................... 143 Release 14.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates. iii
Page 1: ANSYS FLUENT Tutorial Guide ANSYS,
Page 5 and 6: Using This Manual FLUENT Adjoint So
Page 7 and 8: Using This Manual xvi The words sur
Page 9 and 10: Chapter 1: Introduction to Using AN
Page 53 and 54:
Chapter 1: Introduction to Using AN
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
show all

ANSYS FLUENT Tutorial Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?