Microplate Barcode Labeler User Guide - Agilent Technologies

More documents

Recommendations

Info

$Sophisticated peak-based fraction collection – working with up and ...$

80 Chapter 4: Setting up the VCode VCode User Guide 5. Replace the text with a name of your choice. 6. Click Rename profile. 7. Connect the additional VCode to the network using a serial cable, or one or more Ethernet cables. To initialize the communication: 1. Click Use this profile for diagnostics. The plate stage homes. It is not until you use this button that the profile is active. 2. Click Close to close the diagnostics software. Note: You can also click Reinitialize selected VCode profile, which performs the same function. Related information For more information about... Renaming and deleting profiles, and selecting a different profile See... “Working with existing profiles” on page 81
Chapter 4: Setting up the VCode VCode User Guide 81 Working with existing profiles Introduction This topic describes how to work with profiles that have already been created. It describes how to: ❑ Rename a profile ❑ Delete a profile ❑ Select a different profile to allow you to communicate with a different VCode Renaming a profile To rename a profile: 1. In the Device Selection group box of PlateTag, make sure that an Ethernet-based profile is selected if you are connecting using Ethernet or a serial-based profile is selected if you are connecting using serial. 2. Select View > Diagnostics. The VCode Diagnostics dialog box opens after a few seconds. 3. Click the Profiles tab. 4. Select the profile in the Select a profile list box and rename it. The Update Profile button is changed to read Rename Profile. 5. Click Rename Profile. 6. Click Update Profile to save the changes to the profile. Deleting a profile To delete a profile: 1. In the Device Selection group box of PlateTag, make sure that an Ethernet-based profile is selected if you are connecting using Ethernet or a serial-based profile is selected if you are connecting using serial. 2. Select View > Diagnostics. The VCode Diagnostics dialog box opens after a few seconds. 3. Click the Profiles tab. 4. Select the profile you wish to delete from the Select a profile list box. 5. Click Delete profile. 6. Click Close to close the diagnostics software.
Page 1 and 2:
Microplate Barcode Labeler User Gui
Page 3:
Agilent Technologies Letter to our
Page 6 and 7:
ii Table of Contents VCode User Gui
Page 8 and 9:
iv Table of Contents VCode User Gui
Page 10 and 11:
2 Chapter 1: Introduction VCode Use
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
10 Chapter 2: VCode orientation VCo
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
26 Chapter 3: Installing the VCode
Page 36 and 37:
28 Chapter 3: Installing the VCode
Page 38 and 39: 30 Chapter 3: Installing the VCode
Page 66 and 67: 58 Chapter 4: Setting up the VCode
Page 68 and 69: . 60 Chapter 4: Setting up the VCod
Page 92 and 93: 84 Chapter 5: Creating label format
Page 108 and 109: 100 Chapter 5: Creating label forma
Page 116 and 117: 108 Chapter 6: Running a print job
Page 120 and 121: 1 2 3 4 5 6 7 8 9 10 11 12 A B C D
Page 138 and 139:
130 Chapter 6: Running a print job
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
140 Chapter 7: Using the VCode’s
Page 150 and 151:
Page 152 and 153:
. 144 Chapter 7: Using the VCode’
Page 154 and 155:
Page 156 and 157:
. 148 Chapter 7: Using the VCode’
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
156 Chapter 8: VCode ActiveX VCode
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
172 Index VCode User Guide file loc
Page 182 and 183:
174 Index VCode User Guide Rotate18
Page 184:
176 Index VCode User Guide
show all

Microplate Barcode Labeler User Guide - Agilent Technologies

Create successful ePaper yourself

Delete template?

Save as template?