Microplate Barcode Labeler User Guide - Agilent Technologies

More documents

Recommendations

Info

$Sophisticated peak-based fraction collection – working with up and ...$

74 Chapter 4: Setting up the VCode VCode User Guide Placing a plate \ Introduction This topic explains how to correctly place a plate on the plate stage. Procedure To place a plate on the plate stage: 1. Orient the plate so that the A1 well is in the far left corner, matching the A1 label on the plate stage. A1 well 00143 VCode placing plate North West 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 A B C D E F G H I J K L M N O P East South 00143 2. Carefully lower the plate onto the stage, making sure that the plate lies flat.
Chapter 4: Setting up the VCode VCode User Guide 75 About the vertical plate stage positions Introduction This topic gives general information about the vertical plate stage positions. When to change the vertical plate stage position Different types of plates can have different skirt heights. Without a height accommodation, a label positioned optimally in the vertical dimension on one plate will be either too high or too low on a plate that has a significantly different skirt height. To accommodate different skirt heights, the plate stage has two vertical positions, top and bottom. You set the heights of these positions mechanically. You can also specify whether the top or bottom position is used to label a specific plate. This is done in PlateTag through the value of the drop stage field. Before labelling a plate, the plate stage moves to the vertical position specified by the drop stage field. For shallow plates it is best to keep the stage in the top position. For deepwell plates, you may have to drop the stage to the bottom position. If you are using both types of plate, use a different position for each. Plate spacer If you are using a plate with a very short skirt, so that even at the highest stage position the labels are applied too high up, you can use a plate spacer. For more information, contact Velocity11. Using plates of the same height If all of the plates that you intend to use have the same skirt height, you might want to set the top and bottom positions to the same height. By doing this: ❑ You can avoid problems caused by accidentally changing the drop stage value in VCode Diagnostics. ❑ You can establish if one of the stage height positions has drifted. If there is any vertical movement in the stage when you use the drop stage command, drifting has occurred. Related information For more information about... Viewing the drop stage position in VCode Diagnostics Setting the vertical position of the plate stage The drop stage field Setting the drop stage value when creating a schema See... “Checking the basic applicator functions” on page 63 “Setting the heights of the plate stage positions” on page 76 “About label formats and the label editor” on page 84 “Setting the drop stage value” on page 132
Page 1 and 2:
Microplate Barcode Labeler User Gui
Page 3:
Agilent Technologies Letter to our
Page 6 and 7:
ii Table of Contents VCode User Gui
Page 8 and 9:
iv Table of Contents VCode User Gui
Page 10 and 11:
2 Chapter 1: Introduction VCode Use
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
10 Chapter 2: VCode orientation VCo
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33: 24 Chapter 2: VCode orientation VCo
Page 34 and 35: 26 Chapter 3: Installing the VCode
Page 66 and 67: 58 Chapter 4: Setting up the VCode
Page 68 and 69: . 60 Chapter 4: Setting up the VCod
Page 92 and 93: 84 Chapter 5: Creating label format
Page 108 and 109: 100 Chapter 5: Creating label forma
Page 116 and 117: 108 Chapter 6: Running a print job
Page 120 and 121: 1 2 3 4 5 6 7 8 9 10 11 12 A B C D
Page 132 and 133:
124 Chapter 6: Running a print job
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
140 Chapter 7: Using the VCode’s
Page 150 and 151:
Page 152 and 153:
. 144 Chapter 7: Using the VCode’
Page 154 and 155:
Page 156 and 157:
. 148 Chapter 7: Using the VCode’
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
156 Chapter 8: VCode ActiveX VCode
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
172 Index VCode User Guide file loc
Page 182 and 183:
174 Index VCode User Guide Rotate18
Page 184:
176 Index VCode User Guide
show all

Microplate Barcode Labeler User Guide - Agilent Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?