Microplate Barcode Labeler User Guide - Agilent Technologies
Microplate Barcode Labeler User Guide - Agilent Technologies
Microplate Barcode Labeler User Guide - Agilent Technologies
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
1 2 3 4 5 6 7 8 9 10 11 12<br />
A<br />
B<br />
C<br />
D<br />
E<br />
F<br />
G<br />
H<br />
1 2 3 4 5 6 7 8 9 10 11 12<br />
A<br />
B<br />
C<br />
D<br />
E<br />
F<br />
G<br />
H<br />
A<br />
B<br />
C<br />
D<br />
E<br />
F<br />
G<br />
H<br />
A<br />
B<br />
C<br />
D<br />
E<br />
F<br />
G<br />
H<br />
A<br />
B<br />
C<br />
D<br />
E<br />
F<br />
G<br />
H<br />
Chapter 4: Setting up the VCode<br />
VCode <strong>User</strong> <strong>Guide</strong><br />
67<br />
Positions summary<br />
The following table summarizes the positions of the plate stage and<br />
head at various points in a print-and-apply cycle.<br />
Diagram Point in Cycle Plate Stage Position Head Position<br />
Start<br />
Factory-set home<br />
position.<br />
Factory-set position<br />
pointing towards the<br />
printer<br />
00189<br />
Applicator position 2<br />
VCode<br />
00189<br />
00189<br />
00188<br />
UP DOWN<br />
1 2 3 4 5 6 7 8 9 10 11 12<br />
00189<br />
Applicator position 2<br />
VCode<br />
During plate<br />
placing and<br />
pickup<br />
At the robot pickup<br />
angle teachpoint and<br />
one of two heights<br />
defined by the drop<br />
stage value.<br />
The default robot<br />
pickup angle value is<br />
0.<br />
Factory-set position<br />
pointing towards the<br />
printer<br />
As a label is<br />
applied<br />
At the apply angle<br />
teachpoint.<br />
Pointing towards the<br />
plate<br />
00190<br />
1 2 3 4 5 6 7 8 9 10 11 12<br />
00190<br />
Applicator position 3<br />
VCode<br />
!! IMPORTANT !!<br />
Do not attempt to<br />
change this angle<br />
yourself.<br />
The default angle<br />
value is about 349.<br />
UP DOWN<br />
As a bar code is<br />
read<br />
At the bar code angle<br />
teachpoint, with the<br />
far side oriented<br />
towards an optional<br />
bar code reader<br />
mounted to the side<br />
of the printer.<br />
Pointing towards the<br />
printer<br />
1 2 3 4 5 6 7 8 9 10 11 12<br />
00188<br />
!! IMPORTANT !!<br />
Do not attempt to<br />
change this angle<br />
yourself.<br />
The default angle<br />
value is about 259.<br />
Teachpoint retention<br />
The teachpoints are retained when the VCode and computer are turned<br />
off, although they will be lost if you delete the profile used with the<br />
VCode.