Microplate Barcode Labeler User Guide - Agilent Technologies

More documents

Recommendations

Info

$Sophisticated peak-based fraction collection – working with up and ...$

. 60 Chapter 4: Setting up the VCode VCode User Guide Communicating with the VCode Introduction This topic explains how to open communication with the VCode by selecting a profile. Before you start Before you can select a profile, PlateTag must be running. Default profiles The default installation of PlateTag includes two profiles, named: ❑ serial ❑ ethernet When you first use PlateTag, you select one of these profiles. After that, you can create your own profiles and use them instead. First use When you start PlateTag for the first time, the profiles list box is blank. You have to open VCode Diagnostics and then close it for the profiles to show up in the list box. To display the profiles in PlateTag: 1. In PlateTag, navigate to View > Diagnostics. 2. Click Close to close VCode Diagnostics. 3. Restart PlateTag. Connecting to the VCode To connect to the VCode, you select one of the profiles in PlateTag, according to the type of communications cable you are using. To connect to the VCode: 1. In the Device Selection group box of the Print Job page of PlateTag, select the profile that corresponds to the type of connection cable you are using. Note: The COM port defined in the “serial” profile is COM1. If your VCode is connected to another COM port, use VCode Diagnostics to change the COM port of the “serial” profile to the correct one.
Chapter 4: Setting up the VCode VCode User Guide 61 Connecting additional VCodes If you want to connect more than one VCode to the computer, create an additional profile for each. Next step The next step is to verify the communication following the directions in “Starting VCode Diagnostics” on page 62. Related information For more information about... See... Starting PlateTag “Starting PlateTag” on page 58 Connecting additional VCodes Starting VCode Diagnostics “Creating a profile to add a VCode” on page 79 “Starting VCode Diagnostics” on page 62
Page 1 and 2:
Microplate Barcode Labeler User Gui
Page 3:
Agilent Technologies Letter to our
Page 6 and 7:
ii Table of Contents VCode User Gui
Page 8 and 9:
iv Table of Contents VCode User Gui
Page 10 and 11:
2 Chapter 1: Introduction VCode Use
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19: 10 Chapter 2: VCode orientation VCo
Page 34 and 35: 26 Chapter 3: Installing the VCode
Page 66 and 67: 58 Chapter 4: Setting up the VCode
Page 92 and 93: 84 Chapter 5: Creating label format
Page 108 and 109: 100 Chapter 5: Creating label forma
Page 116 and 117: 108 Chapter 6: Running a print job
Page 118 and 119:
110 Chapter 6: Running a print job
Page 120 and 121:
1 2 3 4 5 6 7 8 9 10 11 12 A B C D
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
140 Chapter 7: Using the VCode’s
Page 150 and 151:
Page 152 and 153:
. 144 Chapter 7: Using the VCode’
Page 154 and 155:
Page 156 and 157:
. 148 Chapter 7: Using the VCode’
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
156 Chapter 8: VCode ActiveX VCode
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
172 Index VCode User Guide file loc
Page 182 and 183:
174 Index VCode User Guide Rotate18
Page 184:
176 Index VCode User Guide
show all

Microplate Barcode Labeler User Guide - Agilent Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?