Microplate Barcode Labeler User Guide - Agilent Technologies

More documents

Recommendations

Info

$Sophisticated peak-based fraction collection – working with up and ...$

50 Chapter 3: Installing the VCode VCode User Guide Next step After forming a connection, you can manually set the IP address through the preferences of the VCode’s firmware, as described in “Manually setting the VCode’s IP address” on page 50. Manually setting the VCode’s IP address Introduction This topic describes how to set the IP address of the VCode manually. You would do this only if you are using an Ethernet connection to the VCode and you are setting up a network that does not use a DHCP server to automatically assign IP addresses. The topic also tells you what to do if your VCode currently has a manually assigned IP address and you want to convert it to an automatically assigned address. To learn how this topic fits into the overall process of setting up an Ethernet network, see “Ethernet networking workflows” on page 39. Before you start Before you can manually set the VCode’s IP address, you must connect to the VCode following the directions in “Connecting to the VCode with HyperTerminal” on page 48. Manually assigning the IP address To manually assign the IP address: 1. With the HyperTerminal screen blank, press ENTER. The diagnostics screen for the VCode’s microprocessor opens showing configuration information for it’s firmware. This diagnostics is not the same as VCode Diagnostics.
Chapter 3: Installing the VCode VCode User Guide 51 2. If necessary, use the up or down arrow key on the keyboard to select the IP address line. The selected line has a bright green label and a value with a blue background. The blue background indicates that the value can be changed. 3. Press ENTER to delete the current IP address and type the following new one: 192.168.0.x x is any number from 2–255 that is not already used for a device that will be connected on the same Ethernet network. The number 1 is used for the computer’s network card and cannot be used for a device. Do not use the DELETE or BACKSPACE keys. If you make a mistake, press ENTER again. !! IMPORTANT !! The first three groups of numbers in the IP address must be the same as those of the computer’s network card (192.168.0). 4. Press ENTER to submit the change. If the value that you entered does not follow the correct syntax of an IP address, the original value will be restored. 5. Press q (lower case) to quit the diagnostics. 6. Press ENTER to re-enter the diagnostics, and confirm that the change was made to the IP address. 7. Press q (lower case) to quit the diagnostics.
Page 1 and 2:
Microplate Barcode Labeler User Gui
Page 3:
Agilent Technologies Letter to our
Page 6 and 7:
ii Table of Contents VCode User Gui
Page 8 and 9: iv Table of Contents VCode User Gui
Page 10 and 11: 2 Chapter 1: Introduction VCode Use
Page 18 and 19: 10 Chapter 2: VCode orientation VCo
Page 34 and 35: 26 Chapter 3: Installing the VCode
Page 66 and 67: 58 Chapter 4: Setting up the VCode
Page 68 and 69: . 60 Chapter 4: Setting up the VCod
Page 92 and 93: 84 Chapter 5: Creating label format
Page 108 and 109:
100 Chapter 5: Creating label forma
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
108 Chapter 6: Running a print job
Page 118 and 119:
Page 120 and 121:
1 2 3 4 5 6 7 8 9 10 11 12 A B C D
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
140 Chapter 7: Using the VCode’s
Page 150 and 151:
Page 152 and 153:
. 144 Chapter 7: Using the VCode’
Page 154 and 155:
Page 156 and 157:
. 148 Chapter 7: Using the VCode’
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
156 Chapter 8: VCode ActiveX VCode
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
172 Index VCode User Guide file loc
Page 182 and 183:
174 Index VCode User Guide Rotate18
Page 184:
176 Index VCode User Guide
show all

Microplate Barcode Labeler User Guide - Agilent Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?