Microplate Barcode Labeler User Guide - Agilent Technologies

More documents

Recommendations

Info

$Sophisticated peak-based fraction collection – working with up and ...$

42 Chapter 3: Installing the VCode VCode User Guide Connecting Ethernet cables Introduction This topic describes two ways to connect Ethernet cables between a VCode and the computer. To learn how this topic fits into the overall process of setting up an Ethernet network, see “Ethernet networking workflows” on page 39. Ways to connect You can use Ethernet to connect a VCode to the computer: ❑ Directly ❑ Through a switch If you are setting up a stand-alone VCode, you can use either method. If you are setting up a local area network that will have other devices on it, follow only the directions for using a switch. Before you begin Before starting this procedure, and if you are setting up a new network, make sure that the IP address of the computer’s network card has already been statically assigned. Connecting directly To connect your VCode directly to the computer, will need a crossover Ethernet cable, which can be obtained from a computer supply retail outlet. To connect the VCode directly to the computer with Ethernet: 1. Connect a crossover Ethernet cable to the Ethernet port of the connections panel of the Applicator. Ethernet connector 00151 2. Connect the other end of the cable to the Ethernet port of the computer.
Chapter 3: Installing the VCode VCode User Guide 43 Connecting through a switch An Ethernet switch connects the single cable coming from the computer to one or more cables that lead to one or more devices. A switch is included in the Velocity11 DHCP Server Kit. Note: Do not use a crossover cable with a switch. The switch performs the crossover function. If you are setting up a new network, connect the Ethernet switch to the computer and then connect the VCode to the Ethernet switch using the procedures in this section. If you are adding a VCode to an existing LAN, you do not need to perform the first procedure because the switch should already be connected. To connect the switch to the computer: 1. Connect the power cord to the switch. 2. Plug one end of the Ethernet cable into any Ethernet port of the switch. 3. Plug the other end into the available Ethernet port of the computer. To connect the VCode to the switch: 1. Plug one end of a second Ethernet cable into any available port of the Ethernet switch. 2. Plug the other end into the Ethernet port of the VCode. Connecting additional VCodes You can connect up to six more VCodes to the network through the switch. For each additional VCode you connect, you will need to create an additional profile. Related information For more information about... Creating additional profiles See... “Creating a profile to add a VCode” on page 79
Page 1 and 2: Microplate Barcode Labeler User Gui
Page 3: Agilent Technologies Letter to our
Page 6 and 7: ii Table of Contents VCode User Gui
Page 8 and 9: iv Table of Contents VCode User Gui
Page 10 and 11: 2 Chapter 1: Introduction VCode Use
Page 18 and 19: 10 Chapter 2: VCode orientation VCo
Page 34 and 35: 26 Chapter 3: Installing the VCode
Page 66 and 67: 58 Chapter 4: Setting up the VCode
Page 68 and 69: . 60 Chapter 4: Setting up the VCod
Page 92 and 93: 84 Chapter 5: Creating label format
Page 100 and 101:
92 Chapter 5: Creating label format
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
100 Chapter 5: Creating label forma
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
108 Chapter 6: Running a print job
Page 118 and 119:
Page 120 and 121:
1 2 3 4 5 6 7 8 9 10 11 12 A B C D
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
140 Chapter 7: Using the VCode’s
Page 150 and 151:
Page 152 and 153:
. 144 Chapter 7: Using the VCode’
Page 154 and 155:
Page 156 and 157:
. 148 Chapter 7: Using the VCode’
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
156 Chapter 8: VCode ActiveX VCode
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
172 Index VCode User Guide file loc
Page 182 and 183:
174 Index VCode User Guide Rotate18
Page 184:
176 Index VCode User Guide
show all

Microplate Barcode Labeler User Guide - Agilent Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?