Microplate Barcode Labeler User Guide - Agilent Technologies

More documents

Recommendations

Info

$Sophisticated peak-based fraction collection – working with up and ...$

32 Chapter 3: Installing the VCode VCode User Guide Disconnecting the air tubing Introduction Procedure Before moving or shipping the VCode you need to disconnect the air tubing. You may also need to do this before performing maintenance or cleaning. This topic explains how to disconnect the air tubing without damaging the air input connector. !! DAMAGE HAZARD !! Follow the directions in this topic to correctly disconnect the air tubing from the VCode’s air input connector. To disconnect the air tubing: 1. Turn off the air source so that there is no air pressure to the VCode. 2. Push in the orange locking collar on the quick-release fitting. 00080 VSpin attach air hose Orange locking collar 00080 3. With your free hand, gently pull on the air tubing until it comes free.
Chapter 3: Installing the VCode VCode User Guide 33 Connecting the power cord Introduction This topic explains how to connect the VCode to a power source. Before you start Before you start, read the following warnings. !! DAMAGE HAZARD !! Operating the VCode at the wrong voltage can seriously damage it. !! INJURY HAZARD !! The VCode has moving parts. Keep clothing, hair and jewelry away from it at all times. Procedure To install the power cord: 1. Make sure that the VCode is turned off. The on/off rocker switch on the applicator should be pressed in at the 0 symbol. 2. Make sure that the printer is turned off. The on/off rocker switch on the printer should be pressed in at the 0 symbol. 3. Plug one end of the power cord into the AC power port at the rear of the applicator. 00149 Vcode power cable 00149 4. Plug the other end of the power cord into an appropriate, grounded electrical socket.
Page 1 and 2: Microplate Barcode Labeler User Gui
Page 3: Agilent Technologies Letter to our
Page 6 and 7: ii Table of Contents VCode User Gui
Page 8 and 9: iv Table of Contents VCode User Gui
Page 10 and 11: 2 Chapter 1: Introduction VCode Use
Page 18 and 19: 10 Chapter 2: VCode orientation VCo
Page 34 and 35: 26 Chapter 3: Installing the VCode
Page 66 and 67: 58 Chapter 4: Setting up the VCode
Page 68 and 69: . 60 Chapter 4: Setting up the VCod
Page 90 and 91:
82 Chapter 4: Setting up the VCode
Page 92 and 93:
84 Chapter 5: Creating label format
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
100 Chapter 5: Creating label forma
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
108 Chapter 6: Running a print job
Page 118 and 119:
Page 120 and 121:
1 2 3 4 5 6 7 8 9 10 11 12 A B C D
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
140 Chapter 7: Using the VCode’s
Page 150 and 151:
Page 152 and 153:
. 144 Chapter 7: Using the VCode’
Page 154 and 155:
Page 156 and 157:
. 148 Chapter 7: Using the VCode’
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
156 Chapter 8: VCode ActiveX VCode
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
172 Index VCode User Guide file loc
Page 182 and 183:
174 Index VCode User Guide Rotate18
Page 184:
176 Index VCode User Guide
show all

Microplate Barcode Labeler User Guide - Agilent Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?