Microplate Barcode Labeler User Guide - Agilent Technologies

More documents

Recommendations

Info

$Sophisticated peak-based fraction collection – working with up and ...$

30 Chapter 3: Installing the VCode VCode User Guide Connecting the air tubing: Europe Introduction This topic is for customers in Europe only. It explains how to connect the air tubing to the VCode. To make the VCode compatible with your lab’s air system, you will need to connect the VCode’s 1/4-inch air port to the supplied 6-mm air tubing. This topic describes how to make this connection. Warnings !! INJURY HAZARD !! Switch off the air supply before installing your VCode. When air is flowing you can be injured if the air tubing whips around and strikes you. If you have not been trained in the correct way to handle air tubing, contact your facilities department or the Velocity11 Service Center. !! DAMAGE HAZARD !! Make sure that the air coming into your VCode is dry and free of impurities, such as oil, which can shorten the VCode’s life. If you have any questions about air quality, contact Velocity11. Before you start Before you start, locate the Metric Fittings Kit that is packaged with the VCode’s Utility Kit. Connection assembly The Metric Fittings Kit contains an adapter. The following diagram shows how the adapter is connected to your VCode. Procedure The following procedure is used to set up a direct connection. If you have another instrument connected to the house air supply, you can use the supplied T-connector to connect into the existing air tubing. To connect the metric fittings adapter: 1. Push one end of the nipple (white plastic tube) into the 1/4-inch side (red side) of the adapter. 2. Push the other end of the nipple into the VCode’s air input port. 3. Push the 6-mm tubing into the blue side of the adapter. !! DAMAGE HAZARD !! If you try to insert tubing that has a different diameter, you could damage the adapter. 4. Gently pull on the air tubing to make sure that the assembly is connected properly.
Chapter 3: Installing the VCode VCode User Guide 31 Setting the air pressure Introduction After connecting the air tubing to the VCode you set the air pressure. Procedure To set the air pressure: 1. Turn on the air supply to the VCode. Typically, the mechanism for turning on the air is a pressure regulator located on the wall of your lab. 2. Adjust the air pressure using the pressure regulator knob at the back of the VCode: a. Pull out the knob until you feel a click. b. Turn the knob to increase or decrease pressure, while watching the pressure gauge. The pressure should be set to 68–72 psi (0.47–0.50 MPa). Knob c. Push the knob back in. Related information For more information about... Connecting the air tubing See... ❑ “Connecting the air tubing: North America” on page 29 ❑ “Connecting the air tubing: Europe” on page 30
Page 1 and 2: Microplate Barcode Labeler User Gui
Page 3: Agilent Technologies Letter to our
Page 6 and 7: ii Table of Contents VCode User Gui
Page 8 and 9: iv Table of Contents VCode User Gui
Page 10 and 11: 2 Chapter 1: Introduction VCode Use
Page 18 and 19: 10 Chapter 2: VCode orientation VCo
Page 34 and 35: 26 Chapter 3: Installing the VCode
Page 66 and 67: 58 Chapter 4: Setting up the VCode
Page 68 and 69: . 60 Chapter 4: Setting up the VCod
Page 88 and 89:
80 Chapter 4: Setting up the VCode
Page 90 and 91:
82 Chapter 4: Setting up the VCode
Page 92 and 93:
84 Chapter 5: Creating label format
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
100 Chapter 5: Creating label forma
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
108 Chapter 6: Running a print job
Page 118 and 119:
Page 120 and 121:
1 2 3 4 5 6 7 8 9 10 11 12 A B C D
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
140 Chapter 7: Using the VCode’s
Page 150 and 151:
Page 152 and 153:
. 144 Chapter 7: Using the VCode’
Page 154 and 155:
Page 156 and 157:
. 148 Chapter 7: Using the VCode’
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
156 Chapter 8: VCode ActiveX VCode
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
172 Index VCode User Guide file loc
Page 182 and 183:
174 Index VCode User Guide Rotate18
Page 184:
176 Index VCode User Guide
show all

Microplate Barcode Labeler User Guide - Agilent Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?