Microplate Barcode Labeler User Guide - Agilent Technologies

More documents

Recommendations

Info

$Sophisticated peak-based fraction collection – working with up and ...$

154 Chapter 7: Using the VCode’s bar code reader VCode User Guide Transferring the formats to the reader To transfer the formats to the reader’s firmware: 1. Click Transfer. The Send/Receive settings (BL) dialog box opens. 2. Click Send settings (Save in BL EEP-ROM). The result dialog box opens stating BL setting is finished. If you get the message Failed to set up BL, check the COM port settings and try again. If you get the same message and you are sure that you completed this procedure correctly, call the Velocity11 Service Center. 3. Click OK. 4. Click the close box to close the transfer dialog box. 5. Click Exit. 6. In the Warning dialog box, click OK. There is no need to save settings in the software because they have been saved in the reader’s firmware. 7. Test that the reader works with the new formats. Related information For more information about... Testing the bar code reader See... “Testing the reader using VCode Diagnostics” on page 147.
Chapter 8: VCode ActiveX VCode User Guide 155 VCode ActiveX 8 This chapter gives the ActiveX commands required to control the VCode ® in another company’s automation system.
Page 1 and 2:
Microplate Barcode Labeler User Gui
Page 3:
Agilent Technologies Letter to our
Page 6 and 7:
ii Table of Contents VCode User Gui
Page 8 and 9:
iv Table of Contents VCode User Gui
Page 10 and 11:
2 Chapter 1: Introduction VCode Use
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
10 Chapter 2: VCode orientation VCo
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
26 Chapter 3: Installing the VCode
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
58 Chapter 4: Setting up the VCode
Page 68 and 69:
. 60 Chapter 4: Setting up the VCod
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
84 Chapter 5: Creating label format
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
100 Chapter 5: Creating label forma
Page 110 and 111:
102 Chapter 5: Creating label forma
Page 112 and 113: 104 Chapter 5: Creating label forma
Page 114 and 115: 106 Chapter 5: Creating label forma
Page 116 and 117: 108 Chapter 6: Running a print job
Page 120 and 121: 1 2 3 4 5 6 7 8 9 10 11 12 A B C D
Page 148 and 149: 140 Chapter 7: Using the VCode’s
Page 152 and 153: . 144 Chapter 7: Using the VCode’
Page 156 and 157: . 148 Chapter 7: Using the VCode’
Page 164 and 165: 156 Chapter 8: VCode ActiveX VCode
Page 180 and 181: 172 Index VCode User Guide file loc
Page 182 and 183: 174 Index VCode User Guide Rotate18
Page 184: 176 Index VCode User Guide
show all

Microplate Barcode Labeler User Guide - Agilent Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?