Microplate Barcode Labeler User Guide - Agilent Technologies

More documents

Recommendations

Info

$Sophisticated peak-based fraction collection – working with up and ...$

152 Chapter 7: Using the VCode’s bar code reader VCode User Guide Communicating with the bar code reader Introduction This topic describes how to open a serial communication connection with the bar code reader. You do this when changing the bar code formats stored in the reader. For an overview of the process, see “About changing the reader’s label formats” on page 150. Procedure To open the bar code reader’s software: 1. Copy the BLSet32E.exe file from the bar code reader’s software CD- ROM to the root VCode folder of the controlling computer, when the software is installed to the default location: C:\Program Files\Velocity11\VCode 2. Double-click the file to open the Setup dialog box.
Chapter 7: Using the VCode’s bar code reader VCode User Guide 153 Connecting to the reader To connect to the bar code reader: 1. Click the Files tab and make sure that BL-600 is selected in the Model group box. 2. Click Com port and set the following properties: Property Setting Port The number corresponding to the port that the bar code reader is connected to. This is usually port 1. Baud rate 38400 Data bits 8 bits Parity None Stop 1 bit 3. Click OK. Changing the bar code reader’s formats Introduction This topic describes how to set the bar code reader’s formats in the software and then transfer them to the reader. For an overview of the process of changing the bar code formats stored in the reader, see “About changing the reader’s label formats” on page 150. Before you start Before you can change the bar code format: ❑ The wiring harness must be attached between the VCode and computer, and power supplied to the harness. ❑ The bar code reader software must be open. ❑ A serial connection to the bar code reader must be open. Setting the bar code formats To change the bar code reader’s formats in the software: 1. Click the Code setup tab. 2. In the list boxes of the Code 1, Code 2, Code 3 and Code 4 group boxes, select the four formats that you want your bar code reader to be able to read.
Page 1 and 2:
Microplate Barcode Labeler User Gui
Page 3:
Agilent Technologies Letter to our
Page 6 and 7:
ii Table of Contents VCode User Gui
Page 8 and 9:
iv Table of Contents VCode User Gui
Page 10 and 11:
2 Chapter 1: Introduction VCode Use
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
10 Chapter 2: VCode orientation VCo
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
26 Chapter 3: Installing the VCode
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
58 Chapter 4: Setting up the VCode
Page 68 and 69:
. 60 Chapter 4: Setting up the VCod
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
84 Chapter 5: Creating label format
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
100 Chapter 5: Creating label forma
Page 110 and 111: 102 Chapter 5: Creating label forma
Page 116 and 117: 108 Chapter 6: Running a print job
Page 120 and 121: 1 2 3 4 5 6 7 8 9 10 11 12 A B C D
Page 148 and 149: 140 Chapter 7: Using the VCode’s
Page 152 and 153: . 144 Chapter 7: Using the VCode’
Page 156 and 157: . 148 Chapter 7: Using the VCode’
Page 164 and 165: 156 Chapter 8: VCode ActiveX VCode
Page 180 and 181: 172 Index VCode User Guide file loc
Page 182 and 183: 174 Index VCode User Guide Rotate18
Page 184: 176 Index VCode User Guide
show all

Microplate Barcode Labeler User Guide - Agilent Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?