Microplate Barcode Labeler User Guide - Agilent Technologies

More documents

Recommendations

Info

$Sophisticated peak-based fraction collection – working with up and ...$

. 144 Chapter 7: Using the VCode’s bar code reader VCode User Guide 00177 00177 6. Reconnect the power cable and the communications cable. 7. Turn on the VCode. Related information For more information about... Turning the VCode on or off The location of the power cable The location of Ethernet cable connection The location of the serial cable connection Installing a bar code reader See... “Turning the VCode on and off” on page 58 “Connecting the power cord” on page 33 “Connecting Ethernet cables” on page 42 “Connecting with serial” on page 35 “About installing the bar code reader” on page 142
Chapter 7: Using the VCode’s bar code reader VCode User Guide 145 Positioning the bar code reader Introduction After attaching the bar code reader to the VCode you need to position it and tighten it down. How to do this is described in this topic. Required tools To position and tighten down the bar code reader, you will need 2.5-mm and 4-mm allen wrenches. Laser warnings !! INJURY HAZARD !! Class 2 laser hazard. Looking directly at the laser light may seriously damage your eyes. !! INJURY HAZARD !! Do not disassemble bar code reader sensor heads. Laser emission from the reader is not automatically stopped if the sensor head is disassembled. !! INJURY HAZARD !! Unless following a procedure in a Velocity11 user guide, do not touch the white TEST button on the side of the bar code reader sensor head. This button turns on the laser creating the possibility of a long exposure to the light. Targeting the laser on the label To target the laser light on a label: 1. Put the type of plate that you want to read on the plate stage. 2. Move the stage to the bar code angle teachpoint. 3. Make sure that the plate stage is in the correct vertical position for the type of plate. 4. Press and hold the white button labelled “TEST” on the side of the reader for about 4 seconds. When you release the button the green light next to the label “LASER ON” should remain on. TEST LASER ON 00179 00179 Vcode reader button press 5. Examine the position of the laser lines in relation to the plate label. 6. Adjust the fore-aft position of the bar code reader bracket: If you are only reading bar codes on one side of the plate or bar codes on two, opposite sides of the plate your goal is to have as many lines crossing the bar code as possible, so move the bar code reader bracket as far forward as possible.
Page 1 and 2:
Microplate Barcode Labeler User Gui
Page 3:
Agilent Technologies Letter to our
Page 6 and 7:
ii Table of Contents VCode User Gui
Page 8 and 9:
iv Table of Contents VCode User Gui
Page 10 and 11:
2 Chapter 1: Introduction VCode Use
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
10 Chapter 2: VCode orientation VCo
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
26 Chapter 3: Installing the VCode
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
58 Chapter 4: Setting up the VCode
Page 68 and 69:
. 60 Chapter 4: Setting up the VCod
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
84 Chapter 5: Creating label format
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103: 94 Chapter 5: Creating label format
Page 108 and 109: 100 Chapter 5: Creating label forma
Page 116 and 117: 108 Chapter 6: Running a print job
Page 120 and 121: 1 2 3 4 5 6 7 8 9 10 11 12 A B C D
Page 148 and 149: 140 Chapter 7: Using the VCode’s
Page 156 and 157: . 148 Chapter 7: Using the VCode’
Page 164 and 165: 156 Chapter 8: VCode ActiveX VCode
Page 180 and 181: 172 Index VCode User Guide file loc
Page 182 and 183: 174 Index VCode User Guide Rotate18
Page 184: 176 Index VCode User Guide
show all

Microplate Barcode Labeler User Guide - Agilent Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?