PEHA Product Catalogue 2008 - US Ship Supply

Article Designation Colour Packed Article No. Code No. R
Easywave series flush-mounting receiver, 2 channels
2 separate relay contacts, changeover contact, 1 462 FU-E 378013 3
push to make switch µ 10 A, break contact µ 4 A, 230 V, 50 Hz,
independently programmable, can also be used as
roller shutter module for a roller shutter motor 230 V, 50 Hz,
to be used with all Easywave transmitters, per output one LED and
one control pushbutton with ON-OFF function or 1-5,
rotary switch for function selection and time setting.
Up to 32 transmitters can be assigned to one receiver,
16 transmitters per channel. Each transmitter button can be given
a different receiver function. Aerial 460 ANT is recommended.
Selectable functions:
• ON/OFF with 2-pushbutton operation (e.g. lower
transmitter pushbutton = ON, upper pushbutton = OFF)
• ON/OFF with 1-pushbutton operation of the transmitter
• Only ON with selectable operating time of the transmitter
pushbutton, operating time 0–1.5 sec. or 3 sec.
• Only OFF with selectable operating time of the transmitter
pushbutton, operating time 0–1.5 sec. or 3 sec.
• Sequential pushbutton selector max. 10 sec.
• 0.5–120 min time selectable for stairwell function
• Roller shutter function 1-5, selectable running time:
sequential pushbutton selector, 0.4 sec. impulse, 15 sec.,
30 sec., 90 sec., 150 sec.
• Fan control, e.g. output 1 = speed 1, output 2 = speed 2
Technical data:
Supply voltage 230 V, 50 Hz, neutral conductor necessary,
for mounting on DIN rail, width 72 mm, 4 module widths,
protection class IP 20, screw terminals, both changeover contacts
suitable for single-phase supply.
Switching capacities (push to make switch):
Filament lamps 230 V
2300 W
High voltage halogen lamps 230 V 1500 W
Transformers and inductive loads 600 VA
Motor load
920 VA
Inrush current
max 80 A/20 ms
Electronic ballasts approx. 4 electronic ballasts directly switchable
(dependent on model).
Note electronic ballast peak inrush current.
When switching more a power relay must be used.
Easywave surface-mounting receiver, 2 channels
2 separate relay contacts, changeover contact, grey 1 462 FU-E WA 378313 3
push to make switch µ 10 A, break contact µ 4 A, 230 V, 50 Hz,
independently programmable, can also be used as
roller shutter module for a roller shutter motor 230 V, 50 Hz,
to be used with all Easywave transmitters.
Functions and switching capacities identical to series flush-mounting
receiver 2 channels article no. 462 FU-E but without LED,
without locally-operated control buttons, external inputs for
2 separate pushbutton switches, programmable pushbutton functions.
Technical data:
Supply voltage 230 V, 50 Hz, neutral conductor necessary,
screw terminals, both changeover contacts suitable for single-phase
supply, protection class IP 66, with corresponding M-fixings.
Cable entries: Lengthwise 5 M 16/M 20 cut-outs per side from
top to bottom 2 M 16/M 20 cut-outs per side
with 2 M 20 threaded bushes
Dimensions: L 180 x W 94 x H 66 mm
Easywave, 1–10 V dimmer controller, series flush-mounting,
2 channels
2 outputs for dimming electronic ballasts with 1–10 V DC control 1 463 FU-E 378113 3
input. The outputs are independently programmable. Per output one
LED and one locally-operated control button with ON-OFF function,
rotary switch for function selection and time setting.
Up to 32 transmitters can be assigned to one receiver,
16 transmitters per channel. Each transmitter button can be given
a different receiver function. Aerial 460 ANT is recommended.
Selectable functions:
1-pushbutton operation: Dimmer ON/OFF without memory,
Stop at min. and max.
1-pushbutton operation: Dimmer ON/OFF with memory,
Stop at min. and max.
2-pushbutton operation: Dimmer ON/OFF with memory,
Stop at min. and max.
4-pushbutton operation: ON with memory, OFF, dim until min.,
dim until max.
One pushbutton for retrieving a programmed lighting effect,
one pushbutton for saving and retrieving a lighting effect.
Technical data:
Supply voltage 230 V, 50 Hz, neutral conductor necessary,
for mounting on DIN rail, width 72 mm, 4 module widths,
protection class IP 20, screw terminals,
two outputs 1–10 V DC, each max. I = 45 mA control current,
for each output a separate relay contact, push to make switch µ 4 A,
230 V, 50 Hz, inrush current max. 80 A/20 ms,
electronic ballasts approx. 4 electronic ballasts directly switchable
(dependent on model).
Note electronic ballast peak inrush current.
When switching more a power relay must be used.
Easywave radio
Easywave
radio
43