PEHA Product Catalogue 2008 - US Ship Supply

Article Designation Colour Packed Article No. Code No. R
Motion detector without light sensor
for zone control 848 ZO-xx REG or PHC (motion only), 1 888.02 BM 916297 7
detection angle: 90°, 3 levels,
range: 0.5–15 m,
power supply: 24 V DC,
output: ON/OFF, NPN max. 50 mA,
interior assembly IP 20
PHC
Motion detector without light sensor
for zone control 848 ZO-xx REG or PHC (motion only), 1 888.02 BM-H 916397 7
detection angle: 90°, 1 level,
range: 9 m at installation height of 8 m,
power supply: 24 V DC,
output : ON/OFF, NPN max. 50 mA,
interior assembly IP 20
Cap for outdoors use, motion detector
for motion detector 888.02 BM xx, 1 88 WA 916497 7
for raising protection to IP 54
PHC
Ceiling-mounted presence detector
Surface-mounting, IP 40, dimensions: Ø = 115 mm, H = 38 mm.
Intelligent ceiling-mounted presence detector with dual technology, comprising PIR passive infrared motion detector combined with ultrasonic sensory system,
with integrated fuzzy logic and light sensor, inbuilt learning phase of 4 weeks, suitable for e.g. presence and brightness-dependent room lighting, supply voltage 24 V DC +/- 10%,
from the PHC power supply 940 SPV.
Detection angle: Mounting height approx. 2.5 m, roughly circular PIR motion detection and ultrasonic detection, motion detection can be changed individually
with the aid of enclosed masks
Outputs: 1. Presence output (motion detector combined with ultrasound), brightness-dependent: e.g. for presence and brightness-dependent room lighting,
NPN transistor output, short-circuit-proof, max. 50 mA, for connecting to a 24 V PHC input module 940/24 EM.
2. Presence output (motion detector combined with ultrasound), brightness-dependent: e.g. for presence-dependent fan control,
volt-free push to make switch max. 24 V DC, 50 mA, for connecting to a 24 V PHC input module 940/24 EM.
Brightness threshold: 10–1000 Lux; switching time: 8–40 min.; ultrasonic frequency: 32 kHz.
Required power supply cable for the PHC system JY (ST) Y 2 x 2 x 0.8 mm; air humidity 0–95 %; ambient temperature 0–40 °C.
Ceiling-mounted presence detector
Detection angle: Motion detector 100 m 2 ,
roughly circular; ultrasound 180° lobe-shaped,
approx. 9 m wide, 10 m long; internal consumption 18 mA grey white 1 897.10 PM DE/100 945497 7
as above,
however, detection angle: Motion detector 200 m 2 ,
roughly circular; ultrasound 360° lobe-shaped,
approx. 10 m wide, 18 m long; internal consumption 33 mA grey white 1 897.10 PM DE/200 945597 7
Surface-mounting pattress
for ceiling-mounted presence detector/motion detector
with rear cable entry and
knockout opening for side cable entry,
Ø 128 mm, height 29 mm grey white 1 891.10 241917 7
Twilight/sun sensor
for connecting to the PHC input modules 24 V (REG), 1 941 LUX 257917 7
comprising light sensor (IP 44) and evaluation unit
(2 module widths), for DIN rail,
recommended connecting cable JY (ST) Y 2 x 2 x 0.8 mm,
distance of the light sensor to the evaluation unit max. 100 m,
if necessary use shielding.
Threshold value settings:
Twilight: 1–200 Lux
Switch hysteresis: 1.5 fixed setting
Sun:
2000–200000 Lux
Switch hysteresis: 0.2–0.8 adjustable
Evaluation unit
Auxiliary evaluation unit (2 module widths) for DIN rail 1 941 LUX-REG 257617 7
for the above-mentioned twilight/sun sensor 941 LUX,
for evaluating one additional light value,
up to 10 evaluation units can be operated by one light sensor.
Light sensor
for use as replacement, light sensor IP 44
for the above-mentioned twilight/sun sensor 941 LUX 1 941 LUX-LF 257717 7
33