PEHA Product Catalogue 2008 - US Ship Supply

Article Designation Colour Packed Article No. Code No. R
PHC system box Rolller shutter/venetian blind
The PHC system box Rolller shutter/venetian blind has been
designed for decentralised installation. The box is connected via
the PHC bus to the PHC system. It has 1 x bus input and 2 x bus output
connections. The PHC system box has 8 inputs for conventional
PEHA pushbutton switches and can control up to 4 motors.
The through wiring is either via 3 pole or 5 pole.
In the radio version, the PHC system box has a built-in Easyclick
radio receiver, 2 channels.
Up to 30 battery-free Easyclick transmitters can be trained.
These work in parallel with the conventional pushbuttons.
The PHC system box Rolller shutter/venetian blind can be
programmed from PHC software version V2.54.
3 pole 1 960/3 PSB/JR 265017 7
5 pole 1 960/5 PSB/JR 265117 7
3 pole with radio 1 960/3 FU PSB/JR 272117 7
5 pole with radio 1 960/5 FU PSB/JR 272417 7
PHC
Power supply: 3 pole: 230–250 V AC/
50–60 Hz (L, N, PE)
5 pole: 400–440 V AC/
50–60 Hz (L1, L2, L3, N, PE)
Internal consumption: 60 mA
Inputs:
8 inputs for pushbutton switch, including
maximum 3 switches, 1 input and 2 outputs
for the PHC bus,
1 Easyclick radio receiver, 2 channels
(radio version only)
Transmission frequency for radio: 868.3 MHz
Outputs:
8 N.O. contacts
max. 250 V/16 A
inductive loads 1000 VA/
4 A at 250 V AC
PHC
Protection class: IP 20
Dimensions: L 180 mm x W 205 mm x H 48 mm
Plug-in connectors with cable clamp
for PHC system boxes
jack and plug combination for the supply and pebble grey 1 96/3 BS grau 941497 7
through wiring of 3 pole PHC system boxes, for flexible and
rigid wire 1.5 mm 2 to 2.5 mm 2 without wire end ferrules.
jack and plug combination for the supply and black 1 96/5 BS schwarz 941597 7
through wiring of 5 pole PHC system boxes, for flexible and
rigid wire 1.5 mm 2 to 2.5 mm 2 without wire end ferrules.
six plug-in connectors 3 pole, black 1 96/3 S schwarz 941697 7
for the outputs of the PHC system box Switching, for flexible and
rigid wire 0.75 mm 2 to 2.5 mm 2 without wire end ferrules.
four plug-in connectors 4 pole, black 1 96/4 S schwarz 941797 7
for the outputs of the PHC system box Rolller shutter/venetian blind,
for flexible and rigid wire 0.75 mm 2 to 2.5 mm 2
without wire end ferrules.
four plug-in connectors 5 pole, pastel blue 1 96/5 S blau 941897 7
for the outputs of the PHC system box Dimming, for flexible and
rigid wire 1.5 mm 2 to 2.5 mm 2 without wire end ferrules.
Output module 230 V AC
for mounting on DIN rail, 1 940/4 AM 261617 7
8 relay outputs 4 A,
incl. 30 cm connecting cable,
72 mm wide (4 module widths)
Output module 230 V AC, 4 A DIAG
for mounting on DIN rail, 1 940/4 AM DIAG 244917 7
8 relay outputs 4 A,
with 8 status LEDs
incl. 30 cm connecting cable,
72 mm wide (4 module widths)
Output module 230 V AC
with 8 volt-free relay outputs
for mounting on DIN rail, 1 940/10 AM 260717 7
4 relay outputs 6 A,
4 relay outputs 10 A, incl. 30 cm connecting cable,
108 mm wide (6 module widths),
when switching electronic ballasts and other capacitive loads
the output module 941/10 AM with tungsten pre-closing
contacts is to be used.
Output module 230 V AC
with 8 volt-free relay outputs, DIAG
for mounting on DIN rail, 1 940/10 AM DIAG 244817 7
4 volt-free relay outputs 6 A,
4 volt-free relay outputs 10 A,
with 8 status LEDs,
incl. 30 cm connecting cable,
108 mm wide (6 module widths)
29