PEHA Product Catalogue 2008 - US Ship Supply

More documents

Recommendations

Info

Electronic devices/Light management Article Designation Colour Packed Article No. Code No. R Motion detector 180° Surface-mounting motion detector for wall mounting pure white 1 496.02 BM WAB 979393 3 Technical data: aluminium enamelled* 1 496.70 BM WAB 978893 3 Detection angle: 180° horizontally, 90° vertically sepia brown* 1 496.23 BM WAB 978793 3 Range: revolving lens with two ranges Range 1: max. 12 m = approx. 230 m 2 Range 2: max. 5 m = approx. 40 m 2 Additional angle and range reduction by means of clip-on covers Mounting height: 2.00–2.20 m ON time: 10 sec.–15 min. Light sensor: adjustable from 2–2000 Lux Protection class: IP 44 Supply voltage: 230–240 V, 50 Hz Switching capacity: Relay output, switched L Filament lamps 1000 W Halogen lamps 230 V 500 W Electronic ballasts, approx. 2 electronic ballasts directly switchable (dependent on model). When switching more a power relay must be used. Dimensions: H 120 x W 76 x D 56 mm Accessories: Installation bracket, for installation on outside or inside corners Electronic devices/Light management *Mounting bracket and bottom part black WAB motion detector 180° IR Surface-mounting motion detector IR for wall mounting, WAB design. grey 1 493 BM WAB 978593 3 Technical data: Detection angle: 180° horizontally, 90° vertically Range: max. 8 m Mounting height: approx. 1.1 m and 2.2 m above door Sensor: infrared Twilight setting: 2–2000 Lux Time setting: 10 sec.–30 min. Continuous light: switchable (max. 2 hours, LED on) Supply voltage: 230 V, 50 Hz Contact opening: µ contact opening width relay less than 1.2 mm Switching capacity: max. 1000 W ohmic load max. 500 VA inductive, cos 0.5 max. 2 electronic ballasts, pay attention to inrush currents Dimensions: H 82 x W 72 x D 67 mm Protection class: IP 54 WAB motion detector 140° HF Surface-mounting motion detector HF for wall mounting, WAB design. Not suitable for outdoor use, because it registers every movement. grey 1 493 HF WAB 978693 3 Technical data: Detection angle: 140° horizontally, lobe-shaped, close coverage area 180° Range: 1–8 m infinitely adjustable Mounting height: approx. 1.1 m and 2.2 m above door Sensor: 5.8 GHz high frequency, approx. 1 mW transmit power Twilight setting: 2–2000 Lux Time setting: 10 sec.–30 min. Continuous light: switchable (max. 2 hours, LED on) Supply voltage: 230 V, 50 Hz Contact opening: µ contact opening width less than 1.2 mm Switching capacity: max. 1000 W ohmic load max. 500 VA inductive, cos 0.5 max. 2 electronic ballasts, pay attention to inrush currents Dimensions: H 82 x W 72 x D 64 mm Protection class: IP 54 Flush-mounting base for motion detector 180° Relay base for flush-mounting installation, suitable for motion detector front plate xx.410 BM. Supply voltage 230 V, 50 Hz, 3-lead connection, 1 483 o.A. 389313 3 neutral conductor necessary. Switching capacity: Relay output, µ10 A, 230 V, 50 Hz Filament lamps 230 V 2300 W High voltage halogen lamps 230 V 1500 W Transformers and inductive loads 600 VA Inrush current max. 80 A/20 ms Electronic ballasts, approx. 3 electronic ballasts directly switchable (dependent on model). Note electronic ballast peak inrush current. When switching more a power relay must be used. For connection in parallel of multiple motion detectors use flush-mounting base 493 o.A.. 17
Electronic devices/Light management Article Designation Colour Packed Article No. Code No. R Flush-mounting base for motion detector 180° Triac base for flush-mounting installation, suitable for motion detector front plate xx.410 BM. Supply voltage 230 V, 50 Hz, 2-lead connection. 1 482 o.A. 389213 3 Switching capacity:Filament lamps 230 V 60–400 W High voltage halogen lamps 230 V 60–400 W Transformers and inductive loads 60–300 VA For connection to electronic transformers use flush-mounting base 492 AB o.A. or relay device. For connection in parallel of up to 3 motion detectors, use flush-mounting base 492 AN o.A., 492 AB o.A. or 493 o.A.. Pay attention to minimum loads. Flush-mounting motion detector front plate 180° Passive infrared motion detector for flush-mounting installation, for combinations. STANDARD white 1 80.410 BM w 367613 3 Detection angle: 180° horizontally, pure white 1 80.410.02 BM 367713 3 vertically 20° upwards, vertically 50° downwards DIALOG white 1 95.410.03 BM 367913 3 for angles 0°–60° and 120°–180°, pure white 1 95.410.02 BM 367813 3 vertically 35° downwards agate grey 1 95.410.13 BM 769513 3 for angles 60°–120° deep black 1 95.410.19 BM 368113 3 Lens system: Multi-lens, a double-sided sensor with cobalt blue 1 95.410.49 BM 368413 3 mirror element brown 1 95.410.26 BM 779513 3 Range: Radius 8 m aluminium 1 95.410.70 BM 368513 3 Mounting height: optimum flush-mounting wall installation at 0.80–1.20 m height, with mounting at AURA pure white 1 20.410.02 BM 368613 3 2.20 m height, detection of 1.50 m tall anthracite 1 20.410.21 BM 368713 3 persons from a distance of 0.50 m and over, aluminium 1 20.410.70 BM 368813 3 mounting height 24 mm Protection class: IP 20 Time setting: Infinitely adjustable from 2 sec. to 30 min. Light sensor: Infinitely adjustable from 2 to 1000 Lux, bright Manual operation: Pushbutton on the device for activating continuous light for 2 hours, independent of the light value, with visual indication via LED. After timing out of the continuous light mode, automatic change to automatic operation. Function: Press pushbutton = continuous light for 2 hours, red LED illuminates under the cover. Pressing the pushbutton again within these 2 hours = continuous light function is cancelled, the detector changes to automatic operation again, the red LED under the cover goes out. The light briefly switches itself off. For flush-mounting bases use article no. 483 o.A., 482 o.A. and 482/24 o.A. for individual units. For connection in parallel of flush-mounted inserts use article no. 493 o.A., 492 AB o.A. and 492 AN o.A.. Automatic switch 110° triac version Detection angle: 110° horizontally, 60° vertically, 1 891-2 AS o.A. 990593 3 detector inclined sideways by 20°, optimal for flush-mounting installation at a height of 0.8–1.20 m beside the door Range: approx. 6 m frontal, 4.5 m sideways Supply voltage: 230 V, 50 Hz ON time: adjustable from approx. 15 sec. to 20 min. Light sensor: adjustable from bright (daytime operation) to dark 2-lead triac version, rated switching capacity 40–300 W, filament lamps, selector switch for dim function "Soft-Start" and "Switch-off warning" or conventional switching operation, parallel switching of the automatic switch not permissible Dim function: Soft-Start: the light level is raised to max. in approx. 2 sec. Switch-off warning and Soft-OFF: If no motion is registered after the pre-set timing period is over, the light level is dimmed to 70% for 15 sec. (switch-off warning). If no motion is registered within this 15 sec. period then the light is further dimmed and switched off within 5 sec. (Soft-OFF). If motion is again registered within the 15 sec. switch-off warning period, the light level is raised to 100% and the timing period begins from the start. Automatic switch 110° relay version Detection angle: 110° horizontally, 60° vertically, 1 891-3 AS o.A. 991193 3 detector inclined sideways by 20°, at a height of 0.8–1.20 m beside the door Range: approx. 6 m frontal, 4.5 m sideways Supply voltage: 230 V, 50 Hz ON time: adjustable from approx. 5 sec. to 20 min. Light sensor: adjustable from bright (daytime operation) to dark 3-lead relay version, switching capacity: 1000 W Filament lamps 0500 W 230 V high voltage halogen lamps 0800 VA cos µ = 0.5 max. 1 electronic ballast directly switchable (dependent on model), note electronic ballast peak inrush current. When switching more a power relay must be used. Neutral conductor necessary. 18
Page 1 and 2: Product catalogue
Page 3 and 4: Colour overview STANDARD Inline STA
Page 5 and 6: Representatives IS P ES GB NL B L C
Page 7 and 8: Basic elements Article Designation
Page 9 and 10: Basic elements Article Designation
Page 11 and 12: T5A H250V~ Min Max 7 8 6 1 2 3 4 5
Page 13 and 14: Electronic devices/Light management
Page 17: Electronic devices/Light management
Page 23 and 24: Zone control/Roller shutter control
Page 25 and 26: Zone control/Roller shutter control
Page 27 and 28: PHC Article Designation Colour Pack
Page 41 and 42: PHC Compact Article Designation Col
Page 43 and 44: Easywave radio Article Designation
Page 45 and 46: Easywave radio Article Designation
Page 47 and 48: Easyclick radio Article Designation
Page 57 and 58: STANDARD Article Designation Colour
Page 69 and 70:
STANDARD Article Designation Colour
Page 71 and 72:
STANDARD unbreakable Article Design
Page 73 and 74:
DIALOG Article Designation Colour P
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
AURA Article Designation Colour Pac
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
COMPACTA Built-in range Article Des
Page 97 and 98:
COMPACTA Built-in range Article Des
Page 99 and 100:
Modul 45/Concept 45/Built-in socket
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Hospital/Computer Installation Equi
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Surface-mounting range/COMPACTA Art
Page 123 and 124:
Surface-mounting range Article Desi
Page 125 and 126:
Water-proof range - surface-mountin
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Water-proof range - flush-mounting
Page 133 and 134:
Cast aluminium range - surface/flus
Page 135 and 136:
Cast aluminium range - surface/flus
Page 137 and 138:
Cast aluminium range - built-in ran
Page 139 and 140:
Number index Article No. Code No. R
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
General conditions for the supply o
Page 159 and 160:
Notes 158
Page 161:
Paul Hochköpper GmbH & Co. KG · P
show all

PEHA Product Catalogue 2008 - US Ship Supply

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?