AirLive WL-5470AP User Manual

More documents

Recommendations

Info

System Uptime The time period since the device was up. Firmware Version The current version of the firmware installed in this device. Wireless Mode There are 7 modes supported, The default mode is Access Point. If you want to change to other mode, please click the Mode and select the wireless mode you want. Physical Address Display wireless MAC address information. Band Display wireless band type information. SSID Display the SSID of this device. Channel Number The number of channels supported depends on the region of this Access Point. All stations communicating with the Access Point must use the same channel. Encryption Display encryption setting information. Associated Clients Displays the total number of clients associated to this AP. You can have up to 64 clients to associate to this Access Point. BSSID BSSID displays the ID of current BSS, which uniquely identifies each BSS. In AP mode, this value is the MAC address of this Access Point. LAN Configuration (TCP/IP) Connection Method: Display the connection method, you can setup in TCP/IP section Physical Address: Display the LAN MAC address IP Address: Display the LAN IP address, you can setup in TCP/IP section Network Mask: Display the network mask, you can setup in TCP/IP section Default Gateway: Display the default gateway ip , you can setup in TCP/IP section DHCP Server: Default the DHCP Server is enabled(ON) DHCP Start IP Display the DHCP server start IP address. Address: DHCP Finish IP Display the DHCP server finish IP address. Address: Internet Configuration Connection Method: Display the internet connection method, you can setup in WISP modeWAN Port configuration Physical Address: Display the AP MAC address information IP Address: Display the internet IP Address, you can setup in WISP modeWAN Port configuration Network Mask: Display the network mask, you can setup in WISP modeWAN Port configuration Default Gateway: Display the default gateway , you can setup in WISP modeWAN Port configuration 44 WL5470AP User’s Manual
. Statistics The Statistics table shows the packets sent/received over wireless and ethernet LAN respectively. . Active Clients Display the active Wireless Clients information: Wireless MAC address, Tx/Rx Packet, Tx Rate, and Power Saving information. 45 WL5470AP User’s Manual
Page 1 and 2: WL-5470AP 802.11g Hi Power Multifun
Page 3 and 4: WL-5470AP CE Declaration Statement
Page 5 and 6: FCC Certifications This equipment h
Page 7 and 8: Introduction . WL-5470AP is world's
Page 9 and 10: Parts, Names, and Functions 1. Fron
Page 11 and 12: Factory Default Settings Setting Wi
Page 13 and 14: About the Wireless Operation Modes
Page 15 and 16: Client Mode (Infrastructure) If set
Page 17 and 18: Bridge Mode In this mode, 2 access
Page 19 and 20: Universal Repeater Mode A universal
Page 21 and 22: WISP + Universal Repeater Mode In t
Page 23 and 24: Configuration 1. Start your compute
Page 25 and 26: AP Mode Setting Alias Name You can
Page 27 and 28: Encryption WEP Authentication Type
Page 29 and 30: Encryption Pre-shared Key Group Key
Page 31 and 32: RTS Threshold network, you can ente
Page 33 and 34: When Enable Wireless Access Control
Page 35 and 36: network. Site Survey Channel Number
Page 37 and 38: Advance Setting AP MAC address Site
Page 39 and 40: Security Please refer the AP mode s
Page 41 and 42: Site Survey Security Advance Settin
Page 43 and 44: Advance Setting WAN port Please ref
Page 45 and 46: WISP + Universal Repeater Mode Sett
Page 47 and 48: GW Mode Setting Note: You may need
Page 49: Status In this screen, you can see
Page 53 and 54: Clone MAC Address You can specify t
Page 55 and 56: Other . Upgrade Firmware 1. Downloa
Page 57: This function can list all log info

AirLive WL-5470AP User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?