information booklet - Parchem

P A R C H E M C O N S T R U C T I O N S U P P L I E S
information booklet
Powers Technical Information Booklet August 2011
P: 1800 801 108 www.parchem.com.au

Powers Fasteners
PowerS Fasteners
Powers Fasteners is a global company that has been working on fastening technology for more than 15 years and has
become a specialist in this field. The Powers brand is the first choice when it comes to high load, stress-free adhesive
anchoring. Parchem carries a broad range of high performance chemical anchors (Powers Fasteners) that meets the
needs of DIYers to professional contractors.
This booklet was issued in June 2011 and supersedes all previous booklets with respect to these products.
Due to ongoing research and development, changes may occur to specifications and features without notice. It is
recommended that you download the most current version of the information from www.powers.com.au
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
23 I Parchem Construction Supplies Pty Ltd (ABN 80 069 961 968)

technical information
1
When it comes to
anchoring, Parchem’s
new PRO Adhesive
range gives the
contractor a first!
300ml
AC100E - for medium duty applications
using standard applicator gun.
Gel
Time
Setting
Time @
30 O C
4 mins 25 mins
Styrene Free Polyester
2
Polyester
420ml
KF2 - light to medium duty applications
in hollow brick and blockwork using
screen tubes
4 mins 25 mins
3
Styrene Free Vinylester
385ml
585ml
AC100 ® PRO - for remedial work in solid
and hollow masonry,
i.e. wall ties. Fire Rated.
4 mins 25 mins
4
Pure Epoxy
385ml
585ml
PF PRO - studs for fastening structural
columns and beams requiring high
load transfers. Fire Rated.
20 mins 6 hrs
5
Chem-Stud ® - for the tie down of
equipment.
- 20 mins
Epoxy Acrylate Vinylester
6
Pure Epoxy
385ml
585ml
PF PRO - for high load applications. Ideal
for connecting slabs to cast in slabs. It
works in wet holes too! Fire Rated.
20 mins 6 hrs
7
Pure Epoxy
385ml
585ml
PF PRO - tie down of timber bottom
plates to concrete slab in cyclonic /
near cyclonic regions requiring load
capacities. Fire Rated.
20 mins 6 hrs
Powers Fasteners Technical Information Booklet I 32

powers fasteners
Opposition Equivalent
AC100e
KF2 AC100®PRO Power-Fast®PRO
Ultra fix & 101
Hilti Hit HY150
Hilti HIT-HY
150Max
Hit-MM PLUS & HFX
No longer available, but be aware
HY150 & HY150MAX are two
different products.
ChemsetReo502 & 801
ChemSetMaxima
spin capsules
Powers CHEM-STUD®
Capsule Anchor
Hilt
HVU Capsule
Hilti RE500
KF2
updated April 2011
45 I Parchem Construction Supplies Pty Ltd (ABN 80 069 961 968)

Technical information
Fix Powers
Image Here
Fix Product
PFPRO
name here
v
Hilti Hit Re500
V
Ramset
REO 502
V
Note
Limit State
Fix design
Design
load heading here
Tension Load
(Bond/ Concrete Capacity)
Fisher FIS EM
Doc # Comp 0001
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
Date: 12 th April 2010
In Concrete
Limit State Design Tension Load (kN)
Depth (mm) 80 90 110 125 170 210
PFPRO 17 25 40.8 57.8 98.3 139.2
HIT-RE 500 with HAS 14.3 19.1 27.4 39.9 72.3 104.2
Rod
ChemSet Reo 502 11.4 23.5 34.2 54.7 77.4 96.5
FIS EM 9.8 13.8 20.2 30.7 52.2 77.3
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
M8 M10 M12 M16 M20 M24
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
Note: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72, Ramset
Specifiers Resource Book 2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222
Powers Fasteners Technical Information Booklet I 54

Powers Fasteners
160
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
Limit State
Fix design
Design
load heading here
Tension Load
M8 M10 M12 M16 M20 M24
Note
(Bond/ Concrete Capacity)
Depth (mm) 80 90 110 125 170 210
PFPRO 21.9 30.8 46.6 66.8 107.4 159.2
HIT-RE 500 with HAS
Rod
15.5 20.8 29.8 43.4 78.6 113.3
ChemSet Reo 502 12 24.7 35.9 57.4 81.3 101.3
FIS EM 9.8 13.8 20.2 30.7 52.2 77.3
Note: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72, Ramset
Specifiers Resource Book 2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222
Fix Powers
Image Here
Fix Product
PFPRO
name here
v
Hilti Hit Re500
V
Ramset
REO 502
V
Fisher FIS EM
Doc # Comp 0002
Date: 12 th April 2010
Limit State Design Tension Load (kN)
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
In Concrete
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
67 I Parchem Construction Supplies Pty Ltd (ABN 80 069 961 968)

TECHNICAL INFORMATION
Note
Limit
Fix
State
design load
Design
heading here
Tension Load
Fix Powers
Image Here
Fix Product
AC100PRO
name here
(Bond/ Concrete Capacity)
v
Hilti Hit HY150
V
Fisher FIS V &
FIS VS
Doc # Comp 0003
70
65
60
55
50
45
40
35
30
25
20
15
10
5
0
Date: 12 th April 2010
In Concrete
Limit State Design Tension Load (kN)
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
M8 M10 M12 M16 M20 M24
Depth (mm) 80 90 110 125 170 210
AC100PRO 12.6 18.2 26.5 37.9 55.5 68.7
9.7 12.9 19.3 24.6 41.9 52.2
HIT-HY 150 with HAS
Rod
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
FIS V and FIS VS 8.7 12.2 18.3 27.9 37.9 56.2
Note: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 81, and Fischer Fixing
Systems Technical Handbook 06/2004, Page 176
Powers Fasteners Technical Information Booklet I 76

Powers Fasteners
80
Fix Powers
Image Here
Fix Product
AC100PRO
name here
v
Hilti Hit HY150
V
Note
Limit
Fix
State
design load
Design
heading here
Tension Load
Fisher FIS V &
FIS VS
(Bond/ Concrete Capacity)
Doc # Comp 0004
Date: 12 th April 2010
70
60
50
40
In Concrete
30
20
10
Limit State Design Tension Load (kN)
0
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
M8 M10 M12 M16 M20 M24
Depth (mm) 80 90 110 125 170 210
AC100PRO 14.1 20.3 29.6 42.4 62.1 76.8
10.5 14 21 26.8 45.5 56.8
HIT-HY 150 with HAS
Rod
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
FIS V and FIS VS 8.9 12.5 19.4 29.5 40.1 59.4
Note: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 81, and Fischer Fixing
Systems Technical Handbook 06/2004, Page 176
89 I Parchem Construction Supplies Pty Ltd (ABN 80 069 961 968)

TECHNICAL INFORMATION
Fix design load heading here
Limit State Design Tension Load
(Bond/ Concrete Capacity)
80
75
70
65
60
55
50
45
40
35
30
25
20
15
10
5
0
M8 M10 M12 M16 M20
Depth (mm) 80 90 110 125 170
AC100e /
KF2
8.8 11.8 17.1 28.6 44.5
ChemSet Injection 101 8.2 10.8 15.5 24.2 45.4
Fix reference to opposition manuals here
Fix Powers
Image Here
Fix Product
name KF2 here
v
Fix opposition
Ramset
Product name
here
101
Doc # Comp 0005
Date: 27 th April 2010
Limit State
Fix
Design
design load
Tension
here (kN)
Load (kN)
In Concrete
Note: Information has been extracted f
rom Ramset Specifiers Resource Book 2006, page 134
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
Note
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
Powers Fasteners Technical Information Booklet I 98

Powers Fasteners
Limit State
Fix design
Design
load heading here
Tension Load
(Bond/ Concrete Capacity)
150
140
130
120
110
100
90
80
Ramset
70
60
50
40
30
20
10
0
M8 M10 M12 M16 M20 M24
Note: Information has been extracted f rom Ramset Specifiers Resource Book 2006, page 118 & Ramset Specifiers Resource Book 2006, page 126
Depth (mm) 80 90 110 125 170 210
PFPRO 17 25 40.8 57.8 98.3 139.2
ChemSet Reo 502 11.4 23.5 34.2 54.7 77.4 96.5
ChemSet Injection 801 13.7 17.8 25.9 35.2 61.1 90.2
Fix Powers
Image Here
PFPRO
v
Fix opposition
Product name
here
RE 502
V
Ramset
801
Doc # Comp 0006
Date: 27 th April 2010
Limit State Design Tension Load (kN)
Fix design load here (kN)
In Concrete
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
Note
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
10 11 I Parchem Construction Supplies Pty Ltd (ABN 80 069 961 968)

TECHNICAL INFORMATION
Limit State
Fix design
Design
load heading here
Tension Load
(Bond/ Concrete Capacity)
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
M8 M10 M12 M16 M20 M24
Depth (mm) 80 90 110 125 170 210
PFPRO 17 25 40.8 57.8 98.3 139.2
HVU with HAS Rod 14.3 19.1 27.4 39.9 72.3 104.2
Note: Information has been extracted fromHILTI Australia Fastening Technology Manual Issue 2007, page 54
Fix reference to opposition manuals here
Fix Powers
Image Here
PFPRO
v
Fix opposition
Hilti Product name
here HVU
with HAS Rod
Doc # Comp 0007
Date: 14 th May 2010
Limit State Design Tension Load (kN)
Fix design load here (kN)
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
In Concrete
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
Note
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
Powers Fasteners Technical Information Booklet I 11 10

Powers Fasteners
Working Stress
Fix design load heading
Design
here
Tension Load
Note
(BOND/ Concrete Capacity)
35
30
Fix Powers
Image Here
25
Fix Product
AC100PRO
name here
v
Fix opposition
HILTI
Product name
here
HIT- MM PLUS
Doc # Comp 0008
Date: 14 th May 2010
20
In Concrete
15
Fix design load here (kN)
10
5
Working Stress Design Tension Load (kN)
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
0
M8 M10 M12 M16 M20 M24
Depth (mm) 80 90 110 125 170 210
AC100PRO 5.5 7.9 11.8 16.6 24.3 30.2
HIT-MM PLUS 5 7 10 12 N/A N/A
Note: Information has been extracted from Fix HILTI reference Australia to opposition Anchor manuals Systems, here page 156
12 13 I Parchem Construction Supplies Pty Ltd (ABN 80 069 961 968)

TECHNICAL INFORMATION
140
130
120
110
100
90
80
70
60
Limit State Design Tension Load
(Bond/ Concrete Capacity)
Fix Powers
Image Here
PFPRO
v
AC100PRO
v
Limit State Design Tension Load (kN)
Fix design load here (kN)
In Concrete
50
40
30
20
10
0
M8 M10 M12 M16 M20 M24
Depth (mm) 80 90 110 125 170 210
PFPRO 17.0 25.0 40.8 57.8 98.3 139.2
AC100PRO 12.6 18.2 26.5 37.9 55.5 68.7
KF2 8.8 11.8 17.1 28.6 44.5 64.1
Note
AC100e 8.8 11.8 17.1 28.6 44.5 64.1
Note: Information has been extracted from Powers Fasteners’ Adhesive Anchoring
Systems Design Manual 2009.
KF2 &
AC100e
Doc # Comp 0009
Date: 26 th August 2010
The information is extracted from the Adhesive Anchoring Systems
Design Manual 2009 for GENERAL PURPOSE COMPARISON. It is
strongly recommended to refer to the relevant technical
manual/catalogue for complete product information for design of
anchors and before using the product for a particular application. The
load values in this chart are bond / concrete strength capacities for
single anchors without spacing and / or edge distance restrictions. The
steel capacity of the anchor should be checked and the anchor should
be loaded with in the steel and bond/concrete strength capacity.
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
Powers Fasteners Technical Information Booklet I 13 12

Powers Fasteners
Limit State Design Tension Load
(Bond/ Concrete Capacity in 32MPa Concrete)
140
120
100
80
60
40
20
0
M8 M10 M12 M16 M20 M24
Depth (mm) 80 90 110 125 170 210
PFPRO 17.0 25.0 40.8 57.8 98.3 139.2
V12 12.6 21.3 31.3 47.4 80.6 109.5
AC100PRO 12.6 18.2 26.5 37.9 55.5 68.7
KF2 8.8 11.8 17.1 28.6 44.5 64.1
AC100e 8.8 11.8 17.1 28.6 44.5 64.1
Note
Fix Powers
Image Here
PFPRO
AC100PRO
KF2
Doc # Comp 0009
Date: 14 th Feb 2011
Limit State Design Tension Load
Fix design load here (kN)
(kN)
in 32MPa Concrete
Note: Information has been extracted from Powers Fasteners’ Adhesive Anchoring Systems Design Manual
2009.
V12
AC100e
The information is extracted from the Adhesive Anchoring Systems
Design Manual 2009 for GENERAL PURPOSE COMPARISON. It is
strongly recommended to refer to the relevant technical
manual/catalogue for complete product information for design of
anchors and before using the product for a particular application. The
load values in this chart are bond / concrete strength capacities for
single anchors without spacing and / or edge distance restrictions. The
steel capacity of the anchor should be checked and the anchor should
be loaded with in the steel and bond/concrete strength capacity.
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
14 15 I Parchem Construction Supplies Pty Ltd (ABN 80 069 961 968)

TECHNICAL INFORMATION
Note
Limit State
Fix design load
Design
heading here
Tension Load
Fix Powers
Image Here
(Bond/ Concrete Capacity)
Fix Product
PF PRO
name here
150
125
100
75
v
Hilti
HIT-HY 150
Doc # Comp 0010
Date: 24 th JAN 2010
In Concrete
50
25
Limit State Design Tension Load (kN)
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
0
M8 M10 M12 M16 M20 M24
Depth (mm) 80 90 110 125 170 210
PFPRO 17.0 25.0 40.8 57.8 98.3 139.2
HIT-HY 150 with HAS 9.7 12.9 19.3 24.6 41.9 52.2
Rod
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
Note: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 81, and Hilti international
information (internet version).
Powers Fasteners Technical Information Booklet I 15 14

Powers Fasteners
Fix Powers
Image Here
Note
Limit State
Fix design load
Design
heading here
Tension Load
Fix Product
PF PRO
name here
(Bond/ Concrete Capacity)
v
150
125
100
75
Hilti
HIT-HY150MAX
Doc # Comp 0011
Date: 24 th JAN 2010
In Concrete
50
25
Limit State Design Tension Load (kN)
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
0
M8 M10 M12 M16 M20 M24
Depth (mm) 80 90 110 125 170 210
PFPRO 17.0 25.0 40.8 57.8 98.3 139.2
HIT-HY 150 MAX with 16.4 23.0 33.8 57.1 89.6 121.7
HAS Rod
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
Note: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 81, and Hilti international
information (internet version).
16 17 I Parchem Construction Supplies Pty Ltd (ABN 80 069 961 968)

TECHNICAL INFORMATION
70.0
60.0
Fix Powers
Image Here
Vs
Hilti HIT-HY 150
Vs
Note
Working
Fix
Stress
design load heading
Design
here
Tension Load
Ramset
Structaset 401
(Bond/ Concrete Capacity in 32MPa Concrete)
V12
Vs
Ramset
Chemset 101
Doc # Comp 0012
Date: 04 th Feb 2010
50.0
40.0
30.0
Tension Load (kN)
20.0
Working Stress Design
10.0
0.0
M8 M10 M12 M16 M20 M24
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
Depth (mm) 80 90 110 125 170 210
V12 7.0 11.9 17.4 26.3 44.8 60.8
Structaset 401 6.5 10.1 15.3 20.8 27.7 43.3
HIT-HY 150 6.9 9.2 13.8 17.6 29.9 37.3
Chemset 101 4.5 6.0 8.6 13.5 25.2 42.9
Note: Information has been extracted from Ramset Specifiers Resource Book 2006 and Structaset401 manual downloaded from
internet, HILTI Fastening Technology Manual 2007 (p81 & 86).
Powers Fasteners Technical Information Booklet I 17 16

Powers Fasteners
Fix Powers
Image Here
PFPRO
v
Fix opposition
Ramset
Product name
here
Chemset
REO 502
V
Ramset
Chemset
801
Doc # Comp 0014
Working Stress
Fix design load
Design
heading here
Tension Load
Note
(Bond/ Concrete Capacity)
Date: 10 Feb 2011
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
in 32MPa Concrete
Working Stress Fix design Design load here Tension (kN) Load
(kN)
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
M8 M10 M12 M16 M20 M24 M30
Depth (mm) 80 90 110 125 170 210 270
PFPRO 9.4 13.8 22.6 32.1 54.6 77.3 113.1
ChemSet Reo 502 6.3 10.3* 15.3* 29.4* 43.0 53.6 72.4
ChemSet Injection 801 6.5* 9.9 14.4 19.6 33.9 50.1
Note: Information has been extracted from Ramset Anchoring and Chemicals Product Catalogue 2010 pages 87 and 89.
*Capacities marked with “*” are limited by steel strength as per published information by Ramset. Please check capacity of steel used for anchors as the above
capacities for PFPRO are bond/concrete capacities.
18 19 I Parchem Construction Supplies Pty Ltd (ABN 80 069 961 968)

TECHNICAL INFORMATION
Note
Limit State
Fix design load
Design
heading here
Tension Load
Fix Powers
Image Here
(Bond/ Concrete Capacity)
Fix Product
PF PRO
name here
v
150
125
100
V12
vs
Hilti
HIT-HY150MAX
Doc # Comp 0015
Date: 15 th March 2011
75
In Concrete
50
25
Limit State Design Tension Load (kN)
0
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
M8 M10 M12 M16 M20 M24
Depth (mm) 80 90 110 125 170 210
PFPRO 17.0 25.0 40.8 57.8 98.3 139.2
V12 12.6 21.3 31.3 47.4 80.6 109.5
HIT-HY 150 MAX with 16.4 23.0 33.8 57.1 89.6 121.7
HAS Rod
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
Note: Information has been extracted from HILTI international (internet version).
Powers Fasteners Technical Information Booklet I 19 18

Powers Fasteners
Note
Limit State
Fix design load
Design
heading here
Tension Load
(Bond/ Concrete Capacity)
150
Fix Powers
Image Here
PF PRO
125
V12
100
vs
Ramset
Chemset Reo 502
VS
Ramset
Chemset Injection
801
75
Doc # Comp 0018
Date: 10 th May 2011
50
In 32 MPa Concrete
25
Limit State Design Tension Load (kN)
0
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
M8 M10 M12 M16 M20 M24
Depth (mm) 80 90 110 125 170 210
PFPRO 17.0 25.0 40.8 57.8 98.3 139.2
V12 12.6 21.3 31.3 47.4 80.6 109.5
Chemset Reo 502 11.4 23.5 34.2 54.7 77.4 96.5
Chemset Injection 801 13.7 17.8 25.9 35.2 61.1 90.2
Notes:
Information has been extracted from Ramset Specifiers Resource Book 2006 (pages 118, 126) and Powers Fasteners Adhesive
Technical Manuals.
V12 should not be used in diamond core drilled holes.
20 21 I Parchem Construction Supplies Pty Ltd (ABN 80 069 961 968)

TECHNICAL INFORMATION
Fix Powers
Image Here
PF PRO
Note
Limit State
Fix design load
Design
heading here
Tension Load
v
(Bond/ Concrete Capacity)
150
V12
vs
Hilti
HIT-HY150MAX
125
VS
FISCHER
FIS V and FIS VS
Doc # Comp 0016
100
Date: 16 th March 2011
75
In Concrete
50
25
0
Limit State Design Tension Load (kN)
M8 M10 M12 M16 M20 M24
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
Depth (mm) 80 90 110 125 170 210
PFPRO 17.0 25.0 40.8 57.8 98.3 139.2
V12 12.6 21.3 31.3 47.4 80.6 109.5
HIT-HY 150 MAX with 16.4 23.0 33.8 57.1 89.6 121.7
HAS Rod
FIS V and FIS VS 8.7 12.2 18.3 27.9 37.9 56.2
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page 72. Ramset Specifiers Resource Book
2006, page 118 and Fischer Fixing Systems Technical Handbook 06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE COMPARISON. It is strongly recommended to refer
to the relevant technical manual/catalogue for complete product information for design of anchors and before using the product for a particular
application. The load values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge distance restrictions.
The steel capacity of the anchor should be checked and the anchor should be loaded with in the steel and bond/concrete strength capacity.
Note: Information has been extracted from HILTI international HIT-HY 150MAX with HIT-V/HAS document from internet and Fischer
Fixing Systems Technical Handbook 06/2004, Page 176.
Powers Fasteners Technical Information Booklet I 21 20

Powers Fasteners
Note
Limit State
Fix design load
Design
heading here
Tension Load
(Bond/ Concrete Capacity in 32MPa Concrete)
Fix Powers
Image Here
V12
125.0kN
vs
Hilti
HVU Capsule with
HAS rod
100.0kN
Doc # Comp 0017
75.0kN
50.0kN
Date: 21 st April 2011
In 32MPa Concrete
25.0kN
Limit State Design Tension Load (kN)
The information is extracted from different manufacturer's catalogues
for GENERAL PURPOSE COMPARISON. It is strongly recommended
to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product
for a particular application. The load values in this chart are bond /
concrete strength capacities for single anchors without spacing and /
or edge distance restrictions. The steel capacity of the anchor should
be checked and the anchor should be loaded with in the steel and
bond/concrete strength capacity.
NOTE: Information has been extracted from HILTI Australia Fastening Technology Manual Issue 2007, page
72. Ramset Specifiers Resource Book 2006, page 118 and Fischer Fixing Systems Technical Handbook
06/2004, Page 222.
The information is extracted from different manufacturer’s catalogues for GENERAL PURPOSE
COMPARISON. It is strongly recommended to refer to the relevant technical manual/catalogue for complete
product information for design of anchors and before using the product for a particular application. The load
values in this chart are bond/concrete strength capacities for single anchors without spacing and/or edge
distance restrictions. The steel capacity of the anchor should be checked and the anchor should be loaded
with in the steel and bond/concrete strength capacity.
0.0kN
M8 M10 M12 M16 M20 M24
Depth (mm) 80 90 110 125 170 210
V12 12.6 21.3 31.3 47.4 80.6 109.5
HILTI HVU with HAS rod 14.3 19.1 27.4 39.9 72.3 104.2
Note: Information has been extracted from HILTI Fastening Technology Manual Issue 2007, page 54 and Powers Fasteners’ technical manual on V12.
22 I Parchem Construction Supplies Pty Ltd (ABN 80 069 961 968)

notes
Powers Fasteners Technical Information Booklet I 22

trade stores
We’ve got
the gear
you need
New South Wales
Queensland
Victoria
Beresfield 02 4964 4277
Coffs Harbour 02 6652 3599
Fyshwick 02 6228 1313
Narellan 02 4647 0623
Padstow 02 9771 6626
Penrith 02 4722 9259
Riverstone 02 9627 9133
Tuggerah 02 4352 2287
Wetherill Park 02 9756 5494
Brendale 07 3889 7600
Gladstone 07 4978 0128
Morningside 07 3902 2300
Nerang 07 5527 2227
Springwood 07 3808 8133
Townsville 07 4729 5911
Western Australia
Belmont 08 6279 9799
Berwick 03 9796 1027
Brunswick 03 9380 2400
Campbellfield 03 9308 6133
Dandenong 1300 737 787
South Australia
Hindmarsh 08 8241 6000
www.parchem.com.au
Customer Service 1800 801 108
National Head Office: 7 Lucca Road, Wyong NSW 2259 02 4350 5000
Please recycle
The range of products will vary by location so please contact your nearest store for the range of products in stock.
P: 1800 801 108 www.parchem.com.au