29416 Graepel TH engl. neu:Inhalt - Friedrich Graepel AG

Graepel-Diamond/Cone
Diamond
Cone
Detail A
Detail A
2±0,5
1,5±0,5
14
40
LL 9x12
opposite
rotated 90°
H
ø5
40
LL 9x12
opposite
rotated 90°
H
17 24
unperforated
edge at
custom
made
possible
40
grating length max. 6000 mm
B
sawn
through
perforation
25±3
A
unperforated
edge at
custom
made
possible
10
40
grating length max. 6000 mm
B
sawn
through
perforation
25±3
A
Dimensions
Graepel-Diamond/Cone
Material
thickness
DD 11 mild
DD 11 hot-galvanised/DX51 D pre-galvanised
Stainless steel
ENAW 5754
2.0/2.5/3.0 mm
2.0/2.5/3.0 mm
2.0/2.5/3.0 mm
2.0/2.5/3.0 mm
Graepel-Diamond and Graepel-Cone
These two gratings are used with closed surfaces
in industrial and public areas.
• where “technical utility” has to meet certain
architectural requirements
• where “compromises must be made” i.e.
where certain amount of anti-slip and
displacement space are required and where the
view between two levels must be prevented,
where nothing must drop through and where
good shoe-ware is worn
grating is ideal for indoor
• the lateral system perforation simplifies the
installation of the gratings
Special types
•
all Graepel safety gratings are also available as
flat banks without folded edges here, the
maximum embossed field width must not be
greater than 500 mm for cone and 750 mm for
diamond forms, these flat cuts have a slightly
curved finish
• gratings can also produced with other
•
•
ø 5 mm drain hole
•
dimensions (H/B/L) than those shown above
gratings with unperforated edges or surfaces on
one or both front surfaces are also possible
Graepel-Cone can also be supplied with a
we are at your disposal for further technical
queries
Dimensions
Length (L)
to length divider
Width (B) Diamond
DD 11/DX 51 D/Stainless steel/ENAW 5754
Width divider
Width (B) Cone
DD 11/DX 51 D/Stainless steel/ENAW 5754
Width divider
Heights (H)
6000 mm
40 mm
120–300 mm in every width given for other
gratings
17 mm
120–300 mm in 10 mm increments
10 mm
40/50/75 mm
Stock dimensions see page 43
Anti-slip values Diamond
Material Test No. Evaluation of anti-slip Extrusion
DX51 D pre-galvanised 200423290/3210 R 9 V 10
Anti-slip values Cone
Material Test No. Evaluation of anti-slip Extrusion
DX51 D pre-galvanised** 200423291/3210 R 10 V 8
DD 11 pre-galvanised** 200423293/3210 R 11 V 8
Stainless steel* 200423294/3210 R 11 V 8
ENAW 5754* 200423295/3210 R 11 V 10
* cone height 1.7 mm ** cone height 1.5 mm
Length weight per m Diamond/Cone for material thickness S in [kg/m]
DD 11*/
2.0
DD 11*/
2.5
DD 11*/
3.0
Grating Stainless steel ENAW 5754 Stainless steel ENAW 5754 Stainless steel ENAW 5754
width Height [mm] Height [mm] Height [mm] Height [mm] Height [mm] Height [mm]
[mm] 40 50 75 40 50 75 40 50 75 40 50 75 40 50 75 40 50 75
120 3.7 4.0 4.8 1.3 1.4 1.6 4.5 4.9 5.9 1.6 1.7 2.0 5.3 5.8 7.0 1.8 2.0 2.4
150 4.2 4.5 5.3 1.4 1.5 1.8 5.1 5.5 6.5 1.8 1.9 2.2 6.0 6.5 7.7 2.1 2.2 2.7
180 4.6 5.0 5.8 1.6 1.7 2.0 5.7 6.1 7.1 2.0 2.1 2.4 6.8 7.2 8.4 2.3 2.5 2.9
210 5.1 5.4 6.2 1.8 1.9 2.1 6.3 6.7 7.7 2.2 2.3 2.7 7.5 8.0 9.2 2.6 2.7 3.1
240 5.6 5.9 6.7 1.9 2.0 2.3 6.9 7.3 8.3 2.4 2.5 2.9 8.2 8.7 9.9 2.8 3.0 3.4
270 6.1 6.4 7.2 2.1 2.2 2.5 7.5 7.9 8.9 2.6 2.7 3.1 8.9 9.4 10.6 3.1 3.2 3.6
300 6.6 6.9 7.7 2.3 2.4 2.6 8.1 8.5 9.5 2.8 2.9 3.3 9.6 10.1 11.3 3.3 3.5 3.9
* values apply also for DX 51 D
22