29416 Graepel TH engl. neu:Inhalt - Friedrich Graepel AG

Graepel-Round S
3±1
Detail A
program-controlled
perforation groups
ø14,5
0
-2
ø8
0
-2
40
LL 9x12
opposite
rotated 90°
H
A
unperforated
edge at
custom
made
possible
B
30
40 grating length max. 6000 mm
25±3
sawn
through
perforation
Graepel-Round S
The Graepel-Round S is a universial grating for
use on floor surfaces and treads;
•
•
•
it possesses good anti-slip properties and a
good drainage effect;
the lateral system perforation simplifies the
installation of the gratings
approximately 19% free perforation cross
section for standard grating widths
Program-controlled
perforation groups
•
by means of tool control groups, there is the
ability to set perforating and embossing
punches seperately, this means that not only
rectangular holes can be punched
Special types
•
•
•
•
all Graepel safety gratings are also available as
flat banks without folded edges here, the
maximum embossed field width must not be
greater than 480 mm; these flat cuts have a
slightly curved finish
gratings can also produced with other
dimensions (H/B/L) than those shown above
gratings with unperforated edges or surfaces
on one or both front surfaces are also possible
we are at your disposal for further technical
queries
Dimensions Graepel-Round S
Material
thickness
Dimensions
DD 11 mild
DD 11 hot-galvanised/DX 51 D pre-galvanised
Stainless steel
ENAW 5754
2.0/2.5/3.0 mm
2.0/2.5/3.0 mm
2.0/2.5 mm
2.0/2.5/3.0 mm
Lengths (L)
12000 mm**
to length divider
40 mm
Widths (B)
DD 11/DX 51 D/ENAW 5754
120/150/180/210/240/270/300/330/360/390/420 mm
Stainless steel
120/150/180/210/240/270/300 mm
Width divider
30 mm
Heights (H)
40/50/75 mm
Stock dimensions see page 42
** hot-dip galvanised gratings = L/max. 6000 mm
Anti-slip values
Material Test No. Evaluation of anti-slip Extrusion
DD 11 hot-galvanised 200423286/3210 R 11 V 10
Stainless steel 200423287/3210 R 11 V 10
ENAW 5754 200423288/3210 R 12 V 10
Length weight per meter Round S for material thickness S in [kg/m]
2.0 2.5 3.0
Grating DD 11*/Stainless steel DD 11*/Stainless steel ENAW 5754 DD 11* ENAW 5754
width Height [mm] Height [mm] Height [mm] Height [mm] Height [mm]
[mm] 40 50 75 40 50 75 40 50 75 40 50 75 40 50 75
120 3.5 3.8 4.6 4.3 4.7 5.7 1.5 1.6 2.0 5.1 5.6 6.8 1.8 1.9 2.3
150 4.0 4.3 5.1 4.9 5.3 6.3 1.7 1.8 2.2 5.7 6.2 7.4 2.0 2.1 2.5
180 4.4 4.7 5.5 5.4 5.8 6.8 1.9 2.0 2.3 6.4 6.9 8.1 2.2 2.4 2.8
210 4.8 5.1 5.9 5.9 6.3 7.3 2.0 2.2 2.5 7.0 7.5 8.7 2.4 2.6 3.0
240 5.2 5.2 6.4 6.5 6.5 7.9 2.2 2.4 2.7 7.7 7.7 9.3 2.6 2.8 3.2
270 5.7 5.7 6.8 7.0 7.0 8.4 2.4 2.5 2.9 8.3 8.3 10.0 2.9 3.0 3.4
300 6.1 6.1 7.2 7.5 7.5 8.9 2.6 2.7 3.1 9.0 9.0 10.6 3.1 3.2 3.7
330 6.5 6.5 7.6 8.1 8.1 9.5 2.8 2.9 3.3 9.6 9.6 11.3 3.3 3.5 3.9
360 7.0 7.0 8.1 8.6 8.6 10.0 3.0 3.1 3.4 10.2 10.2 11.9 3.5 3.7 4.1
390 7.4 7.4 8.5 9.2 9.2 10.6 3.1 3.3 3.6 10.9 10.9 12.6 3.7 3.9 4.3
420 7.8 7.8 8.9 9.7 9.7 11.1 3.3 3.5 3.8 11.5 11.5 13.2 4.0 4.1 4.5
* values apply also for DX 51 D
14