Crocus SHDSL Repeater 2P - Route 66 Communications
Crocus SHDSL Repeater 2P - Route 66 Communications Crocus SHDSL Repeater 2P - Route 66 Communications
44 Crocus SHDSL Repeater 2P Chapter 4 User manual Monitor interface ALARM This command displays the actual alarm status. RR_03_FMM> ALARM ---------------------------------------------------------------------- Local Alarm Status N/C Side ---------------------------------------------------------------------- LOS/LFA-H : off off SEGD : off off BER-H : off off LOOP2 : off ALB : off off TEST : off off ---------------------------------------------------------------------- RR_03_FMM> Definitions: LOS/LFA-H SEGD Loss of signal or frame alignment at SHDSL loop. Segment Defect indication. BER-H SHDSL block-error-rate according G.826 ≥ 30%. LOOP2 ALB TEST N-side SHDSL test loop 2 is active. Analog loop-back is active. At least one test function is active. RESET This command completely restarts the Crocus SHDSL Repeater 2P. RR_03_FMM> RESET system reset
Crocus SHDSL Repeater 2P Chapter 4 45 User manual Monitor interface 4.7 Configuration management (CM) This sub-menu groups all the commands for configuring the Crocus SHDSL Repeater 2P. When entering this sub-menu, the following is displayed: Configuration management activated Enter to return to MAIN, or for HELP information The configuration commands are the following: CONFIG This command displays the current configuration settings of the Crocus SHDSL Repeater 2P. RR_00_CM> CONFIG ---------------------------------------------------------------------- Local Configuration N-Side C-Side ---------------------------------------------------------------------- xDSL Master/Slave : Slave Master Mode : Dual Pair Dual Pair Annex : B B Autorestart : on on PLL : on on Base Rate : 20 24 Rate Adaption : on on ---------------------------------------------------------------------- RR_00_CM> After each configuration change, the new configuration is automatically displayed. MODE This command sets respectively the N-side and C-side to single or dual pair mode. • Syntax: MODE [S|D,S|D] • Example: ANNEX D,D PLL This command sets the PLL of channel A of respectively the N-side and C-side to on or off. • Syntax: PLL [ON|OFF,ON|OFF] • Example: PLL OFF,OFF ANNEX This command sets respectively the N-side and C-side to a certain SHDSL Annex. • Syntax: ANNEX [A|B|AUTO,A|B] • Example: ANNEX AUTO,A AUTORESTART This command allows you to toggle between auto-restart on or off for the N-side and C-side respectively. • Syntax: AUTORESTART [ON|OFF,ON|OFF] • Example: AUTORESTART ON,OFF
- Page 1 and 2: Crocus SHDSL Repeater 2P Crocus SHD
- Page 3 and 4: Crocus SHDSL Repeater 2P User manua
- Page 5 and 6: Crocus SHDSL Repeater 2P User manua
- Page 7 and 8: Crocus SHDSL Repeater 2P User manua
- Page 9 and 10: Crocus SHDSL Repeater 2P 1 User man
- Page 11 and 12: Crocus SHDSL Repeater 2P Chapter 1
- Page 13 and 14: Crocus SHDSL Repeater 2P Chapter 1
- Page 15 and 16: Crocus SHDSL Repeater 2P Chapter 1
- Page 17 and 18: Crocus SHDSL Repeater 2P Chapter 2
- Page 19 and 20: Crocus SHDSL Repeater 2P Chapter 2
- Page 21 and 22: Crocus SHDSL Repeater 2P Chapter 2
- Page 23 and 24: Crocus SHDSL Repeater 2P Chapter 2
- Page 25 and 26: Crocus SHDSL Repeater 2P Chapter 2
- Page 27 and 28: Crocus SHDSL Repeater 2P Chapter 2
- Page 29 and 30: Crocus SHDSL Repeater 2P Chapter 2
- Page 31 and 32: Crocus SHDSL Repeater 2P Chapter 2
- Page 33 and 34: Crocus SHDSL Repeater 2P Chapter 2
- Page 35 and 36: Crocus SHDSL Repeater 2P Chapter 2
- Page 37 and 38: Crocus SHDSL Repeater 2P Chapter 3
- Page 39 and 40: Crocus SHDSL Repeater 2P Chapter 3
- Page 41 and 42: Crocus SHDSL Repeater 2P Chapter 3
- Page 43 and 44: Crocus SHDSL Repeater 2P Chapter 3
- Page 45 and 46: Crocus SHDSL Repeater 2P Chapter 4
- Page 47 and 48: Crocus SHDSL Repeater 2P Chapter 4
- Page 49 and 50: Crocus SHDSL Repeater 2P Chapter 4
- Page 51: Crocus SHDSL Repeater 2P Chapter 4
- Page 55 and 56: Crocus SHDSL Repeater 2P Chapter 5
- Page 57 and 58: Crocus SHDSL Repeater 2P Chapter 5
- Page 59 and 60: Crocus SHDSL Repeater 2P Chapter 5
- Page 61 and 62: Crocus SHDSL Repeater 2P Chapter 5
- Page 63 and 64: Crocus SHDSL Repeater 2P Chapter 5
- Page 65 and 66: Crocus SHDSL Repeater 2P 57 Annex A
- Page 67 and 68: Crocus SHDSL Repeater 2P Annex A: 5
- Page 69 and 70: Crocus SHDSL Repeater 2P Annex Inde
<strong>Crocus</strong> <strong>SHDSL</strong> <strong>Repeater</strong> <strong>2P</strong> Chapter 4 45<br />
User manual<br />
Monitor interface<br />
4.7 Configuration management (CM)<br />
This sub-menu groups all the commands for configuring the <strong>Crocus</strong> <strong>SHDSL</strong> <strong>Repeater</strong> <strong>2P</strong>. When entering<br />
this sub-menu, the following is displayed:<br />
Configuration management activated<br />
Enter to return to MAIN, or for HELP information<br />
The configuration commands are the following:<br />
CONFIG<br />
This command displays the current configuration settings of the <strong>Crocus</strong> <strong>SHDSL</strong> <strong>Repeater</strong> <strong>2P</strong>.<br />
RR_00_CM> CONFIG<br />
----------------------------------------------------------------------<br />
Local Configuration N-Side C-Side<br />
----------------------------------------------------------------------<br />
xDSL<br />
Master/Slave : Slave Master<br />
Mode : Dual Pair Dual Pair<br />
Annex : B B<br />
Autorestart : on on<br />
PLL : on on<br />
Base Rate : 20 24<br />
Rate Adaption : on on<br />
----------------------------------------------------------------------<br />
RR_00_CM><br />
After each configuration change, the new configuration is automatically displayed.<br />
MODE<br />
This command sets respectively the N-side and C-side to single or dual pair mode.<br />
• Syntax: MODE [S|D,S|D]<br />
• Example: ANNEX D,D<br />
PLL<br />
This command sets the PLL of channel A of respectively the N-side and C-side to on or off.<br />
• Syntax: PLL [ON|OFF,ON|OFF]<br />
• Example: PLL OFF,OFF<br />
ANNEX<br />
This command sets respectively the N-side and C-side to a certain <strong>SHDSL</strong> Annex.<br />
• Syntax: ANNEX [A|B|AUTO,A|B]<br />
• Example: ANNEX AUTO,A<br />
AUTORESTART<br />
This command allows you to toggle between auto-restart on or off for the N-side and C-side respectively.<br />
• Syntax: AUTORESTART [ON|OFF,ON|OFF]<br />
• Example: AUTORESTART ON,OFF