WJ60, WJ90: Operating Guide - Hasler Inc.
WJ60, WJ90: Operating Guide - Hasler Inc.
WJ60, WJ90: Operating Guide - Hasler Inc.
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>Operating</strong><br />
<strong>Guide</strong><br />
Mailing Systems<br />
And Solutions<br />
HASLER<br />
America’s better choice<br />
<strong>WJ60</strong> / <strong>WJ90</strong><br />
Obsolete Product<br />
An ISO 9001 Quality System<br />
Certified company
Model Number ____________________<br />
Serial Number ____________________<br />
Dealer Phone ____________________<br />
<strong>Hasler</strong> , <strong>Inc</strong>.<br />
19 Forest Parkway<br />
Shelton, CT 06484-6140<br />
TEL 800/793-0180<br />
203/926-1087<br />
Obsolete Product<br />
FAX 203/929-6084<br />
E-Mail info@haslerinc.com<br />
Web: http://www.haslerinc.com
HASLER Customer Comment Card<br />
<strong>WJ60</strong>/<strong>WJ90</strong> <strong>Operating</strong> <strong>Guide</strong> 06/2003 Form 50813<br />
We at <strong>Hasler</strong> would like to hear your comments about this manual and our<br />
product.<br />
Please, fill out the following form and mail to:<br />
Jim Koonz<br />
or FAX to: Jim Koonz<br />
P.O. Box 858 (203)-925-2441<br />
19 Forest Parkway<br />
Shelton, CT 06484-0904<br />
Jkoonz@haslerinc.com<br />
Rate The Manual<br />
by checking the<br />
appropriate box.<br />
What did you like?<br />
Great<br />
Very<br />
Good<br />
Good<br />
Fair Poor Very<br />
Poor<br />
Obsolete Product<br />
What didn’t you like?<br />
Are there any improvements or features that you would like to see added<br />
to the product?<br />
Optional Information:<br />
Name<br />
Phone Number<br />
Company<br />
Thanks, we appreciate your response.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong>
This page intentionally left blank.<br />
Obsolete Product
HASLER<br />
Publication Notice<br />
This manual is a non-controlled document.<br />
This manual has been carefully compiled and checked for<br />
accuracy. Information in this manual does not constitute a<br />
warranty of performance. Furthermore, <strong>Hasler</strong>®, <strong>Inc</strong>.<br />
reserves the right to revise this publication and make<br />
changes, from time to time, in its content.<br />
<strong>Hasler</strong>®, <strong>Inc</strong>. ASSUMES NO LIABILITY WHATSOEVER FOR<br />
ANY LOSSES OR DAMAGES INCURRED AS A RESULT OF<br />
INFORMATION CONTAINED IN THIS MANUAL.<br />
Proprietary Notice<br />
Obsolete Product<br />
This publication contains information proprietary and<br />
confidential to <strong>Hasler</strong>®, <strong>Inc</strong>. Any reproduction, disclosure, or<br />
use of this publication is expressly prohibited <strong>Hasler</strong>®, <strong>Inc</strong>.<br />
may otherwise authorize in writing.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Pub - 1
HASLER<br />
Introduction<br />
The <strong>WJ60</strong>/<strong>WJ90</strong> has many capabilities that will be important<br />
to your business:<br />
As well as being productive (up to 5400 items per hour),<br />
the <strong>WJ60</strong>/<strong>WJ90</strong> is designed to be a user-friendly machine<br />
that can fit into any working environment with its innovative<br />
and attractive design, simple user settings and very low noise<br />
level. The high volume capacity and sealed inker makes it<br />
easy and safe to handle, and the user interface is particularly<br />
clear with a graphic interface and 5 memories to store favorite<br />
jobs.<br />
The <strong>WJ60</strong>/<strong>WJ90</strong> is adaptable and as such can handle many<br />
different types of mail up to 3/8 inches thick. The optional<br />
feeder can be used to process, in a continuous cycle, items<br />
of sizes ranging from a small size of 3 1/2 inches by 5 1/2<br />
inches<br />
Obsolete<br />
to a large size of 6 3/8 inches<br />
Product<br />
to 9 inches and up to 6<br />
mm thickness. For thicker mail items or packages, adhesive<br />
labels can be automatically dispensed.<br />
The <strong>WJ60</strong>/<strong>WJ90</strong> is connectable. It can exchange data with<br />
<strong>Hasler</strong> scales and printers in order to provide optimal mail<br />
processing and reporting.<br />
Finally, the <strong>WJ60</strong>/<strong>WJ90</strong> is a unique communication tool for<br />
your company. Its high quality printing combined with its<br />
integrated library of message/advertising slogans, and free<br />
format text will afford you extra tools to enhance your<br />
company’s image and the impact of your mail.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong>
HASLER<br />
Cautions & FCC<br />
Cautions<br />
Do not under any circumstances attempt to remove the<br />
machine covers or attempt to repair the <strong>WJ60</strong>/<strong>WJ90</strong>. There<br />
are no operator serviceable parts.<br />
The <strong>WJ60</strong>/<strong>WJ90</strong> product is licensed for use under the<br />
auspices of the Post Office. This license is issued subject to<br />
the product being secure at all times. Any removal of covers<br />
or disassembly of the product will result in the license being<br />
revoked and may result in the Post Office requesting <strong>Hasler</strong><br />
to remove the product from use.<br />
The ink cartridge system used within the <strong>WJ60</strong>/<strong>WJ90</strong><br />
contains Post Office approved ink. This cartridge should not<br />
be tampered with in any way or the use of non-approved inks<br />
be undertaken. This will breach any Post Office license<br />
agreement on the product and may result in the Post Office<br />
requesting <strong>Hasler</strong> to remove the product from use.<br />
Obsolete Product<br />
FCC Compliance Statement<br />
This equipment has been tested and found to comply with the<br />
limits for a Class A digital device, pursuant to Part 15 of the<br />
FCC Rules. These limits are designed to provide reasonable<br />
protection against harmful interference when the equipment is<br />
operated in a commercial environment. This equipment<br />
generates, uses, and can radiate radio frequency energy and,<br />
if not installed and used in accordance with this instruction<br />
manual, may cause harmful interference to radio<br />
communications. Operation of this equipment in a residential<br />
area is likely to cause harmful interference, in which case the<br />
user will be required to correct the interference at his/her own<br />
expense.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> FCC - 1
HASLER<br />
Cautions & FCC<br />
Modem Approval Requirements<br />
This equipment contains a modem which has been approved<br />
for connection to analog public switched telephone networks.<br />
However, due to differences between individual telephone<br />
networks provided in different areas, the approval does not, of<br />
itself, give an unconditional assurance of successful<br />
operation on every network termination point.<br />
In the event of problems, you should contact your equipment<br />
supplier in the first instance.<br />
Installation Safety<br />
The power plug on this equipment is intended to serve as the<br />
device for isolation of the electrical supply. The equipment<br />
should be installed in close proximity to an easily accessible<br />
grounded power supply and analog telephone socket.<br />
WARNING: FOR SAFETY THIS EQUIPMENT MUST BE<br />
GROUNDED<br />
Obsolete Product<br />
The <strong>WJ60</strong> and <strong>WJ90</strong> Mailing Machines have been designed<br />
to meet the safety requirements of UL1950. The peripheral<br />
interfaces meet the SELV requirements of that standard,<br />
therefore in order to maintain the level of safety provided by<br />
the <strong>WJ60</strong> and <strong>WJ90</strong>, the interface of any equipment<br />
connected to the <strong>WJ60</strong> and <strong>WJ90</strong> interfaces must also meet<br />
the SELV requirements of UL1950.<br />
FCC - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER<br />
Table of Contents<br />
Installation<br />
Installation Tips 1-1<br />
Fitting the Moistener Unit Wick 1-2<br />
Attach the Moistener Unit/Platform Infill to the Plain Platform 1-2<br />
Attach the Moistener/Platform Infill to the Autofeed 1-3<br />
Attach the <strong>WJ60</strong>/<strong>WJ90</strong> to the Hand Feed Platform or 1-3<br />
Autofeed<br />
Attach the Weigh Platform & Support (Option) 1-4<br />
Fill the Label Dispenser 1-5<br />
Connect The Weigh Platform (optional device) 1-6<br />
Connect AutoFeed (optional device) 1-7<br />
Connect The Telephone Line 1-8<br />
Connect The Power Cord 1-9<br />
Position The Receiving Tray 1-10<br />
Fill The Moistener Reservoir 1-11<br />
Controls & Features<br />
Control Descriptions 2-2<br />
Control Locations 2-3<br />
Function Keys 2-4<br />
Obsolete Product<br />
Sample Indicia 2-5<br />
Display 2-5<br />
Printing Postage<br />
Printing Tips 3-2<br />
To Log On (PIN Entry Mode) 3-3<br />
Departmental Operation 3-4<br />
How To Select A Postage Value 3-6<br />
Low Credit / Insufficient Credit 3-8<br />
High Value Selection 3-8<br />
Stamping An Envelope 3-9<br />
To Change A Department 3-10<br />
To Log Off 3-10<br />
To Print Postage With Autofeed 3-11<br />
To Clear A Jam 3-13<br />
Printing With Labels 3-15<br />
Printing With A Weigh Platform 3-18<br />
Calculating The Correct Postage 3-19<br />
Print Modes 3-22<br />
Print Mode Selection 3-23<br />
Modifying The Imprint 3-24<br />
Choosing a Slogan, Rate Die Or Text 3-25<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong>
HASLER<br />
Table of Contents<br />
Date Advance (for Pre Dating Mail) 3-26<br />
Maintaining Print Quality 3-28<br />
Cleaning The Ink Cartridge 3-28<br />
Making a Test Print 3-29<br />
Low Ink / No Ink 3-31<br />
Replacing An Ink Cartridge 3-32<br />
Envelope Moistener<br />
Using the Envelope Moistener with Plain Platform 4-1<br />
Using the Envelope Moistener with an Autofeed 4-2<br />
Filling the Reservoir 4-2<br />
Meter Registers<br />
Sample Register Displays 5-1<br />
Meter Register Selection 5-2<br />
Printing a Register 5-4<br />
Printing Registers with External Printer 5-5<br />
Adding Postage<br />
Modem Connection 6-2<br />
Obsolete Product<br />
Adding Postage 6-2<br />
‘WARNING PENDING CREDIT’ Procedure 6-3<br />
Clearing A PO Lockout 6-4<br />
Maintaining Your TMS Account Number 6-5<br />
TMS Account Number 6-5<br />
TMS Account Balance 6-5<br />
TMS Statements 6-6<br />
Post Office Regulations 6-6<br />
PostageNow 6-7<br />
PostageNow TeleFunds 6-8<br />
PostageNow OnDemand 6-8<br />
Information whenever you want it online or by phone 6-8<br />
Managing Your Account 6-9<br />
Standard TMS Bank Accounts 6-10<br />
Where To Mail Your TMS Bank Account Deposit 6-11<br />
Contact Information 6-12<br />
Memory Functions<br />
Saving A Memory Function 7-1<br />
Recalling A Memory Function 7-2<br />
<strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER<br />
Cautions & FCC<br />
Supervisor Settings<br />
Entry to Supervisor Mode 8-2<br />
Departments Control 8-4<br />
Changing the User PIN 8-5<br />
Setting the User Status 8-6<br />
To Assign a Department 8-7<br />
To Change a Department Name 8-9<br />
Department Code 8-10<br />
To Change the Department Status 8-11<br />
To Reset the Department Registers 8-11<br />
<strong>WJ60</strong>/<strong>WJ90</strong> Machine Setup Menu 8-12<br />
Machine Setup 8-14<br />
High Value 8-14<br />
Low Credit 8-15<br />
Time 8-16<br />
Sleep Mode 8-17<br />
Key Beep 8-17<br />
Default Stamp Value 8-18<br />
Registration (Change Address, Audit, Withdraw) 8-19<br />
Telephone Settings 8-20<br />
Obsolete Product<br />
Memory Cards 8-22<br />
How To Replace Data Using a Memory Card 8-24<br />
Text Messages 8-26<br />
Reports / Printing A Report 8-28<br />
Setting the Report Destination 8-30<br />
Printing with External Printer 8-31<br />
Appendix A<br />
Contact Information A-1<br />
How To Perform Common Functions A-2<br />
Troubleshooting Tips A-3<br />
Appendix B<br />
Country Codes<br />
Index<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong>
This page intentionally left blank.<br />
Obsolete Product
HASLER Installation Section 1<br />
Installation Tips<br />
Your <strong>WJ60</strong>/<strong>WJ90</strong> should be installed on a flat horizontal<br />
surface adjacent to easily accessible power and telephone<br />
line outlets.<br />
Allow sufficient free space as follows:<br />
• above the machine to enable opening of the covers.<br />
• at the rear of the machine for cooling.<br />
The power plug on this equipment is intended to serve as the<br />
device for isolation of the mains supply; where possible it is<br />
advisable to connect to a switched power outlet.<br />
Do not connect your <strong>WJ60</strong>/<strong>WJ90</strong> Postage Meter to the power<br />
outlet until you have attached the accessories.<br />
Obsolete Product<br />
Installation Tips 1-1<br />
Fitting the Moistener Unit Wick 1-2<br />
Attach the Moistener Unit/Platform Infill to the Plain Platform 1-2<br />
Attach the Moistener/Platform Infill to the Autofeed 1-3<br />
Attach the <strong>WJ60</strong>/<strong>WJ90</strong> to the Hand Feed Platform or 1-3<br />
Autofeed<br />
Attach the Weigh Platform & Support (Option) 1-4<br />
Fill the Label Dispenser 1-5<br />
Connect The Weigh Platform (optional device) 1-6<br />
Connect AutoFeed (optional device) 1-7<br />
Connect The Telephone Line 1-8<br />
Connect The Power Cord 1-9<br />
Position The Receiving Tray 1-10<br />
Fill The Moistener Reservoir 1-11<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 1 - 1
HASLER Installation Section 1<br />
Postage Meter<br />
Fitting the Moistener Unit Wick<br />
• First remove the moistening wick from its packaging.<br />
• Before fitting ensure that the wick is thoroughly wetted.<br />
• Raise the brush, then take the wetted wick and feed<br />
into the water trough as shown.<br />
• Lower the brush into place.<br />
Attach the Moistener Unit/Platform Infill to the Handfeed<br />
Platform<br />
When attaching the Moistener Unit/ Platform Infill to the<br />
Handfeed Platform, ensure that the Tabs and Slots interlock<br />
as illustrated.<br />
Obsolete Product<br />
Page 1 - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Installation Section 1<br />
Attach the Moistener/Platform Infill to the Autofeed<br />
If an Autofeed is to be fitted, first attach the Moistener<br />
Unit/Platform Infill to the Autofeed ensuring that the slots on<br />
the Autofeed fit tightly over the tabs on the Moistener Unit/Infill<br />
Platform as illustrated.<br />
Obsolete Product<br />
Attach the <strong>WJ60</strong>/<strong>WJ90</strong> to the Hand Feed Platform or<br />
Autofeed<br />
Lower the <strong>WJ60</strong>/<strong>WJ90</strong> into position so that the slots fit over<br />
the tabs as illustrated.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 1 - 3
HASLER Installation Section 1<br />
Attach the Weigh Platform & Support (Option)<br />
Sufficient cable has been provided with your weigh platform to<br />
enable the unit to be placed on the desk adjacent to the<br />
postage meter if this is preferred.<br />
Position the weigh platform on its support. Excess cable can<br />
be loosely coiled under the support.<br />
Position the Support Platform so that the pins on the<br />
underside fit into the locating points on the rear casing of the<br />
<strong>WJ60</strong>/<strong>WJ90</strong>.<br />
Obsolete Product<br />
Page 1 - 4 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Installation Section 1<br />
Fill the Label Dispenser<br />
Obsolete Product<br />
The labels are designed to meet United States Postal Service<br />
and <strong>Hasler</strong> requirements. Use Only United States Postal<br />
Service and <strong>Hasler</strong> approved labels.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 1 - 5
HASLER Installation Section 1<br />
Connect The Weigh Platform (optional device)<br />
Weigh<br />
Platform<br />
Obsolete Product<br />
Page 1 - 6 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Installation Section 1<br />
Connect AutoFeed (optional device)<br />
Optional AutoFeed<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 1 - 7
HASLER Installation Section 1<br />
Connect The Telephone Line<br />
This connection is used for postage loading and needs only to<br />
be connected when the actual postage loading is being<br />
performed.<br />
Obsolete Product<br />
The telephone line must be a direct analog line to do postage<br />
loading.<br />
Page 1 - 8 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Installation Section 1<br />
Connect The Power Cord<br />
Power is connect via a standard 3-prong plug into a wall outlet<br />
of 120 VAC 60 Hz.<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 1 - 9
HASLER Installation Section 1<br />
Position The Receiving Tray<br />
The receiving tray is used to catch the mail as it is process<br />
through the mailing system.<br />
Obsolete Product<br />
Receiving<br />
Tray<br />
Page 1 - 10 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Installation Section 1<br />
Fill The Moistener Reservoir<br />
For safety, always disconnect the postage meter from the<br />
power supply when filling the moistener reservoir, keep the<br />
postage meter top cover closed and take care not to spill<br />
sealing solution onto the machine.<br />
Open the reservoir compartment and fill with <strong>Hasler</strong> sealing<br />
solution.<br />
Close the reservoir compartment.<br />
Obsolete Product<br />
Reservoir<br />
Compartment<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 1 - 11
This page intentionally left blank.<br />
Obsolete Product
HASLER Controls Section 2<br />
Controls & Features<br />
The following pages detail the Controls and Features<br />
associated with your <strong>WJ60</strong>/<strong>WJ90</strong> mailing system, please<br />
take the time to read them carefully.<br />
Control Descriptions 2-2<br />
Control Locations 2-3<br />
Function Keys 2-4<br />
Sample Indicia 2-5<br />
Display 2-5<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 2 - 1
HASLER Controls Section 2<br />
1 Display Presents a visual indication of the machine set<br />
up and status.<br />
2 Soft Keys Keys with functions as depicted on the display.<br />
3 Numeric Enable the operator to access user functions.<br />
Keypad &<br />
Function Keys<br />
4 Start / Stop Used to Start/Stop the Machine.<br />
Button<br />
5 Autofeed Automatic envelope feeder.<br />
6 Envelope <strong>Guide</strong> Adjustable envelope guide.<br />
7 Side <strong>Guide</strong> Adjustable envelope guide.<br />
8 Feed Platform Provides a flat surface to assist feeding of mail.<br />
9 Receiving Tray Collects printed mail.<br />
10 Weigh Platform In conjunction with the <strong>WJ60</strong>/<strong>WJ90</strong> will weigh<br />
and calculate postage for items up to 2kg.<br />
11 Weigh Platform<br />
Support<br />
Supports the weigh platform and provides a<br />
cable tidy.<br />
12 Precut Label Holds up to 50 labels.<br />
Dispenser<br />
13<br />
Obsolete<br />
Label Release Release to fill the<br />
Product<br />
Precut Label Dispenser.<br />
Lever<br />
14 Infill Unit Standard supplied Infill Platform or optional<br />
Moistener Platform.<br />
15 Memory Card<br />
Reader<br />
Used to load new postage rate and customer<br />
data.<br />
16 Ink Cartridge Ink Cartridge/Printing Head.<br />
17 Power Input 110 - 120V AC 60Hz input.<br />
18 Accessory Port Connection for printer etc.<br />
19 Weigh Platform<br />
Connection<br />
Connection for weigh platform or an external<br />
scale.<br />
20 Autofeed Connection for Autofeed Unit.<br />
Connector<br />
21 Telephone<br />
Socket<br />
Enables connection to TMS Center for postage<br />
loading. An analog phone line is required<br />
(standard fax machines use analog phone<br />
lines).<br />
22 Meter Cover May be removed to allow access to meter.<br />
Page 6 - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 01/2003
HASLER Controls Section 2<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 2 - 3
HASLER Controls Section 2<br />
Function Keys<br />
Job Memory<br />
Label Key<br />
Description<br />
Storing and recalling memorized<br />
jobs.<br />
Label Mode selection<br />
Menu Key<br />
Access to Function Menu<br />
Lock<br />
Return to Standby/Locking<br />
Funds<br />
Access to Load Funds<br />
(Recredit)<br />
Weigh<br />
Obsolete<br />
Weigh Platform<br />
Product<br />
Mode selection<br />
Platform<br />
Clear Key<br />
Used to clear an entry<br />
Confirmation<br />
Key<br />
Used to confirm an entry or<br />
selection<br />
Numeric Keys<br />
Start/Stop Key<br />
through<br />
Used to enter numeric values<br />
Envelope / Label Feed<br />
Start / Stop button<br />
Page 6 - 4 <strong>WJ60</strong>/<strong>WJ90</strong> 01/2003
HASLER Controls Section 2<br />
LOW INK is a Resource Level Indicator<br />
$150.20 is the money left in the meter<br />
MARKETING is the selected department<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 2 - 5
This page intentionally left blank.<br />
Obsolete Product
HASLER Printing Section 3<br />
Introduction<br />
In order to achieve the best impression, your <strong>WJ60</strong>/<strong>WJ90</strong><br />
requires an even surface on which to print, therefore on bulky<br />
or uneven items correct folding of the contents will help<br />
considerably. Use a label if in doubt.<br />
Printing Tips 3-2<br />
To Log On (PIN Entry Mode) 3-3<br />
Departmental Operation 3-4<br />
How To Select A Postage Value 3-6<br />
Low Credit / Insufficient Credit 3-8<br />
High Value Selection 3-8<br />
Stamping An Envelope 3-9<br />
To Change A Department 3-10<br />
To Log Off 3-10<br />
To Print Postage With Autofeed 3-11<br />
To Clear A Jam 3-13<br />
Printing With Labels 3-15<br />
Printing With A Weigh Platform 3-18<br />
Calculating The Correct Postage 3-19<br />
Print Modes 3-22<br />
Print Mode Selection 3-23<br />
Modifying The Imprint 3-24<br />
Choosing a Slogan, Rate Die Or Text 3-25<br />
Date Advance (for Pre Dating Mail) 3-26<br />
Maintaining Print Quality 3-28<br />
Cleaning The Ink Cartridge 3-28<br />
Making a Test Print 3-29<br />
Low Ink / No Ink 3-31<br />
Replacing An Ink Cartridge 3-32<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3-1
HASLER Printing Section 3<br />
Printing Tips<br />
If your mail contains staples, paper clips and other fixings, it is<br />
recommended that the fixings be situated at the bottom of the<br />
envelope. This will avoid the risk of damage to your printing<br />
head. In the event that a satisfactory print cannot be achieved<br />
due to bulky contents (maximum 3/8 inch) the envelope<br />
should be treated as a packet and a label used.<br />
It is recommended that the <strong>WJ60</strong>/<strong>WJ90</strong> is left powered on at<br />
all times. This will assist in maintaining print quality.<br />
In the event that you have to power the machine down:<br />
1. Press to allow the machine to return to standby<br />
mode.<br />
2. Wait for approximately one minute to allow the ink cartridge<br />
to return to the park position.<br />
3. Then remove the power.<br />
Obsolete Product<br />
Page 3 - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
To Log On (PIN Entry Mode)<br />
To enter USER mode from the Standby screen:<br />
Press the [USER] key. The machine will enter Ready mode.<br />
HASLER<br />
If the machine is protected by a USER PIN the following<br />
screen will be observed:<br />
Note: This number may be changed or removed by the supervisor.<br />
ENTER USER PIN<br />
Obsolete<br />
- - - - -<br />
Product<br />
If the correct PIN is entered the Ready Mode screen will be<br />
observed.<br />
$150.20<br />
09/19/02<br />
50.00<br />
$0.00<br />
USER<br />
If an incorrect PIN is entered the machine will continue to<br />
prompt for USER PIN entry.<br />
If an incorrect PIN is entered for eight or more attempts, the<br />
meter will be locked, in this event please refer to Setting the<br />
User Status.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 3
HASLER Printing Section 3<br />
The Default Stamp Value is factory set to $0.00, to change<br />
this value, please refer to Supervisor Settings.<br />
The machine is supplied with all departments set to OFF. In<br />
order to activate the departments, please refer to<br />
Departments Control.<br />
Departmental Operation<br />
If your machine has been set for departmental operation a list<br />
of available departments will be observed:<br />
1 MARKETING<br />
2 ACCOUNTS<br />
3 SALES<br />
4<br />
5<br />
Obsolete Product<br />
Using the and keys, or an appropriate number<br />
key, select your department from the list and press<br />
confirm.<br />
to<br />
If your department is protected, you will be prompted to enter<br />
your Department PIN:<br />
ENTER DEPARTMENT PIN<br />
- - - - -<br />
Continued on the next page.<br />
Page 3 - 4 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
Enter the PIN using the numerical keypad. If the PIN is<br />
correct the Department Ready screen will be observed:<br />
$150.20<br />
09/19/02<br />
MARKETING<br />
$0.00<br />
If not you will be prompted to try again. (The Department PIN<br />
is not the same as the User PIN. The Department PIN may<br />
be changed or removed by the supervisor, please refer to<br />
page 58).<br />
If your department is not protected, you will not be prompted<br />
to enter the Department PIN and the Department Ready<br />
Screen will be observed. Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 5
HASLER Printing Section 3<br />
How To Select a Postage Value<br />
Using the numerical keypad, enter the required postage<br />
(example: 37 cents press [3] [7]), the value display will flash:<br />
$150.20<br />
09/19/02<br />
MARKETING<br />
$0.37<br />
If an incorrect value is entered, press<br />
the correct value.<br />
and enter<br />
To confirm the value, press<br />
now be observed.<br />
$150.20<br />
09/19/02<br />
MARKETING<br />
, the following display will<br />
Obsolete Product<br />
$0.37<br />
Note: The icon will only be present if the machine is set for<br />
departmental operation.<br />
Page 3 - 6 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
Low Credit (Funds)<br />
When machine credit falls below or equal to the low credit<br />
level, the LOW CREDIT indicator will be observed:<br />
LOW CREDIT $0.37<br />
$49.50<br />
09/19/02<br />
MARKETING<br />
It is now time to add more credit.<br />
The default Low Credit value is factory set to $50.00, to<br />
change this value please refer to the Supervisor Settings<br />
Section 8.<br />
Insufficient Credit (Funds)<br />
When the value selected exceeds the available credit,<br />
franking will be disabled and the INSUFFICIENT CREDIT<br />
screen will be observed:<br />
Obsolete Product<br />
INSUFFICIENT CREDIT<br />
$0.80<br />
$0.95<br />
To ADD CREDIT (load funds), please refer to Adding Postage<br />
Section 6.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 7
HASLER Printing Section 3<br />
High Value Selection<br />
If a value greater than or equal to the High Value setting is<br />
selected, the machine will not print unless the high value<br />
setting is confirmed.<br />
The default High Value Threshold is set at $10.00 (To change<br />
the High Value setting, please refer to Supervisor Settings<br />
page 61).<br />
Printing a high value<br />
From Ready Mode, set the required postage value<br />
(e.g. $12.50) and press to confirm.<br />
The High Value warning screen will now be observed:<br />
$12.50<br />
HIGH VALUE – ARE YOU SURE?<br />
$0.80<br />
Obsolete Product<br />
Printing is disabled.<br />
Press to return to Ready Mode screen with the High<br />
Value confirmed.<br />
If you wish to reject the High Value value selection,<br />
enter the correct value and press to confirm.<br />
The High Value Warning will be observed, if the value is now<br />
correct press to return to Ready Mode with the new<br />
high value confirmed.<br />
If you are franking more than one item at a high value, always<br />
check that the value is correct for all items being processed.<br />
Note: The High Value Warning is automatically suppressed<br />
when values are received<br />
from a Weigh Platform.<br />
You Are Now Ready To Process Your Mail<br />
Page 3 - 8 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
Stamping an Envelope<br />
Insert the envelope with the side to be printed facing upwards<br />
as illustrated.<br />
Press the<br />
button, after a short<br />
pause the<br />
motor will start.<br />
Franked envelopes will<br />
subsequently be<br />
deposited into the<br />
receiving tray.<br />
Note: For an envelope<br />
exceeding 3/8 inch (10mm) thick, a label must be used.<br />
Maximum is ¼ inch thickness when using the Autofeed or<br />
Mositener.<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 9
HASLER Printing Section 3<br />
To Change a Department<br />
From Department Ready Mode, press the button to<br />
display the list of available departments, then using the<br />
and keys, or the appropriate number key,<br />
select your department from the list.<br />
Press<br />
to confirm.<br />
1 MARKETING<br />
2 ACCOUNTS<br />
3 SALES<br />
4<br />
5<br />
Obsolete Product<br />
If the department is protected, you will be prompted to enter<br />
your new Department PIN.<br />
If the PIN is correct the new Department Ready screen will be<br />
observed:<br />
$150.50<br />
09/19/02<br />
ACCOUNTS<br />
$0.37<br />
If the PIN is incorrect the prompt to enter the Department PIN<br />
will be repeated.<br />
To Log Off<br />
From any screen, press the<br />
screen.<br />
key to go to the Standby<br />
Page 3 - 10 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
To Print Postage With Autofeed<br />
Used in conjunction with the <strong>WJ60</strong>/<strong>WJ90</strong>, the Automatic<br />
Feeder permits a large range of envelope sizes and<br />
thicknesses to be processed.<br />
Envelope feeding<br />
Check that all envelopes have been sorted into stacks of<br />
same size, thickness and<br />
denomination with the<br />
address facing upwards and<br />
the top edge of the<br />
envelopes all the same side<br />
of the stack.<br />
Take one envelope from the<br />
stack and place it on the<br />
platform, address side upwards with the top edge against the<br />
left-hand side as shown.<br />
Obsolete Product<br />
Move the rear guide forward until the edge of the envelope<br />
aligns with the face of the guide.<br />
Move the side guide towards the envelope leaving sufficient<br />
clearance to allow the envelope to move freely.<br />
Return the envelope to its stack.<br />
Fan the envelopes to separate<br />
them<br />
Continued on the next page.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 11
HASLER Printing Section 3<br />
Bevel the edge of the stack<br />
Place the envelopes on the feed<br />
platform, with their upper edge<br />
resting against the side guide as shown.<br />
Ensure that the<br />
envelopes are stacked<br />
along the side and<br />
front guides. If<br />
necessary, re-adjust<br />
the side guide by<br />
resting it against the<br />
envelopes without<br />
pressing.<br />
Obsolete Product<br />
Press the button, after a short pause the motor will<br />
start. Franked envelopes will subsequently be deposited into<br />
the receiving tray.<br />
The envelopes in a stack should rest against the backside<br />
guide of the unit to ensure proper feeding<br />
Note: Envelopes exceeding 1/4 inch (6mm) in thickness<br />
should be hand fed, for an envelope exceeding 3/8 inch<br />
(10mm) thick, a label must be used.<br />
Page 3 - 12 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
To Clear A Jam<br />
In the unlikely event of an envelope misfeed, the following<br />
procedure must be followed:<br />
When using an Autofeed the whole of the following<br />
procedure must be followed, when an Autofeed is not<br />
connected, start from operation 7.<br />
When using an Autofeed the whole of the following procedure<br />
must be followed, when an Autofeed is not connected, start<br />
from operation 7.<br />
1. Remove all free<br />
envelopes from the feed<br />
tray;<br />
2. Open the Autofeed top<br />
cover;<br />
Obsolete Product<br />
3. Using the thumb and<br />
fore finger, squeeze the<br />
sliders to release the feed<br />
mechanism as illustrated;<br />
4. Remove the obstruction;<br />
5. Close the feed mechanism by applying downwards<br />
pressure to the top of the feed mechanism until it is heard to<br />
click home;<br />
6. Close the Autofeed top cover.<br />
Continued on the next page.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 13
HASLER Printing Section 3<br />
7. From Ready Mode, press the key, the MAIN MENU<br />
screen will be observed:<br />
1 REGISTERS<br />
2 CARTRIDGE<br />
3 SUPERVISOR<br />
4 CLEAR MAIL PATH<br />
8. Using the and keys, or the appropriate<br />
number key, move the cursor to CLEAR MAIL PATH and<br />
press<br />
observed:<br />
to confirm, the following screen will be<br />
Obsolete Product<br />
PRESS START<br />
9. Press the button.<br />
After a short pause the track should clear and the screen<br />
return to the MAIN MENU.<br />
10. Press to return to Ready Mode.<br />
You are now ready to resume stamping your mail.<br />
Page 3 - 14 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
Printing With Labels<br />
Filling the Label Dispenser<br />
The label dispenser is an integral part of the <strong>WJ60</strong>/<strong>WJ90</strong><br />
Franking Machine and when filled will take up to 50 labels.<br />
Open the top cover to gain access to the label release lever.<br />
Labels are inserted in the dispenser with the tab uppermost<br />
and the label side to be franked facing the direction of travel.<br />
Obsolete Product<br />
Using one finger, apply pressure to the label release lever<br />
thus allowing the labels to drop into contact with the feed<br />
mechanism, then release the lever.<br />
Close the top cover.<br />
Continued on the next page.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 15
HASLER Printing Section 3<br />
<strong>Hasler</strong> Approved Labels are supplied in boxes of 1000.<br />
Please refer to Appendix A for information on ordering<br />
<strong>Hasler</strong> approved supplies.<br />
Printing a Label<br />
When feeding labels, first select the postage value required,<br />
press the label key<br />
observed:<br />
the following screen will be<br />
To return to the Ready Mode screen with Label selection<br />
cancelled, press .<br />
Obsolete Product<br />
To frank a single label press the button, a single label<br />
will be printed at the displayed value.<br />
If you are required to print more than one label, use the<br />
numerical keypad to enter the number of labels to be<br />
processed (1 - 99).<br />
and re-<br />
If an incorrect quantity is entered, press<br />
enter the correct quantity.<br />
To frank labels press the<br />
button.<br />
The machine will print automatically the required number of<br />
labels at the displayed value.<br />
Page 3 - 16 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
If during the label printing process the following display is<br />
observed:<br />
First replenish the label dispenser, then press<br />
to complete the label printing process.<br />
Take up the franked label, peel off the backing sheet and affix<br />
the label to the parcel or packet.<br />
The<br />
Obsolete<br />
machine will return automatically<br />
Product<br />
to the Ready Mode<br />
screen with label selection cancelled.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 17
HASLER Printing Section 3<br />
Printing With A Weigh Platform<br />
Used in conjunction with your <strong>WJ60</strong>/<strong>WJ90</strong>, the weigh platform<br />
will weigh and calculate the correct rate and value for items<br />
up to 5 pounds.<br />
Setting of values for printing is automatic.<br />
When postal rates change, your machine may be updated by<br />
installing a Rate Card which can be obtained from <strong>Hasler</strong>.<br />
For information relating to the installation of new postal rates,<br />
refer to Supervisor Settings Section 8.<br />
Weigh Platform Preparation<br />
Ensure that the weigh platform is plugged in to the correct<br />
port at the back of the machine and that the platform surface<br />
is clear of any obstruction.<br />
Obsolete Product<br />
From Ready mode, press .<br />
The WEIGH PLATFORM screen will now be observed:<br />
Current RATE setting will be displayed. If NO WEIGH<br />
PLATFORM is displayed instead of the Weight and Postage<br />
Rate, check scale connection and start again.<br />
Note: If the weight indicated exceeds 0 lbs. with no item on<br />
the Weigh Platform, press<br />
to Zero the weigh platform.<br />
Page 3 - 18 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
Calculating The Correct Postage<br />
To change the RATE setting press , the RATES<br />
screen will be observed:<br />
A list of Postage Rates currently available will now be<br />
displayed.<br />
To return to the previous screen with Rate setting unchanged,<br />
Obsolete Product<br />
press .<br />
Using the and keys, or the appropriate<br />
number key, select required Rate option from list, (e.g. 8<br />
Auto 5 digit Let) press to confirm.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 19
HASLER Printing Section 3<br />
The following typical screen will now be observed:<br />
Make your selections as required and return to the WEIGH<br />
PLATFORM screen.<br />
Place item to be weighed on the platform, the weight and<br />
postage will be displayed.<br />
Obsolete Product<br />
For some rates you will be prompted to make further<br />
selections for example:<br />
SERVICE: 1 Certified Mail or 2 Registered & Ins or 3 COD ;<br />
DESTINATION: 1 Canada or 2 Mexico or 3 Int Let Group 3 ;<br />
If you wish to accept the Postage displayed, press<br />
displayed.<br />
to return to Ready Mode with the postage value<br />
Page 3 - 20 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
You Are Now Ready To Print Postage At The Correct<br />
Postage<br />
If you wish to reject the Postage displayed, press ,<br />
you will be returned to the RATES screen where you may<br />
revise your settings.<br />
To weigh further items repeat the procedure.<br />
Zero (Tare) Function<br />
1. Press: .<br />
2. Place an empty container on the platform.<br />
3. Press: , zero weight will now be displayed.<br />
4. Place the filled container on the platform. The weight now<br />
displayed will be that of the contents of the container.<br />
5. To return to normal use, clear the scale platform and<br />
press<br />
the displayed weight will return to 0 lbs.<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 21
HASLER Printing Section 3<br />
Print Modes<br />
Normal (Postage)<br />
Date Only<br />
Slogan Only<br />
Slogan & Date<br />
Stamp – No Date<br />
Text Only<br />
Pass Through<br />
Prints stamp, date, and any selected slogan<br />
Prints the date instead of a franking mark<br />
Prints a slogan instead of a frank mark.<br />
Prints a slogan and the date instead of a<br />
frank mark.<br />
Prints stamp with no date.<br />
Prints your personalized text message<br />
instead of a stamp mark.<br />
Moistens and seals envelopes only when<br />
fitted with a Moistener.<br />
Normal (Postage) Mode<br />
In Normal (Postage) mode, you can print postage, select a<br />
message from a number of pre-loaded messages (Slogans)<br />
or select one from two of your own design (when ordered<br />
from <strong>Hasler</strong>). In addition to a Slogan you can compose and<br />
print your own Text, you can also select from a number of<br />
Rate Dies.<br />
Obsolete Product<br />
It is also possible to Advance Date your mail by up to seven<br />
days. When fitted with a Moistener it is also possible to<br />
moisten and seal envelopes.<br />
Up to 8 preloaded messages,<br />
2 messages to customer<br />
design<br />
Page 3 - 22 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
Print Mode Selection<br />
From Ready Mode, press the<br />
selection screen will be observed:<br />
Current Mode will be displayed.<br />
key, the MODE<br />
In addition to the Normal (Postage) Mode, any of the Print<br />
Mode functions may be accessed directly from the MODE<br />
screen:<br />
Obsolete Product<br />
Using the and keys, or the appropriate<br />
number key, select required option from list, (e.g. DATE<br />
ONLY) press<br />
to confirm.<br />
Or to return to Ready Mode with mode setting unchanged,<br />
press .<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 23
HASLER Printing Section 3<br />
Modifying The Imprint<br />
The IMPRINT menu is used to modify the setup of the imprint.<br />
From Ready Mode, press the<br />
screen will be observed:<br />
key the following<br />
Slogan<br />
Rate Die<br />
Text<br />
Date Advance<br />
You may select one Slogan from seven<br />
pre-loaded Slogans (plus two personalized<br />
Slogans).<br />
You may select one Rate Die from seven<br />
pre-loaded Rate Dies.<br />
Up to five personal text messages may be<br />
set (see Supervisor Settings page 68).<br />
The posting date can be advanced by up to<br />
seven days.<br />
Obsolete Product<br />
Page 3 - 24 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
Choosing a Slogan, Rate Die or Text<br />
You can select a Slogan and/or Rate Die from a number of<br />
pre-loaded Slogans/Rate Dies, you can even compose and<br />
print your own Text Messages (please refer to Supervisor<br />
Settings Section 8)<br />
Slogans, Rate Dies and Text Messages may be combined<br />
within the same Imprint. (Provided the envelope or label is<br />
long enough to take the print).<br />
The method of selection for Slogans, Rate Dies and Text is<br />
the same, therefore for the purpose of this example we will<br />
illustrate selecting a Slogan.<br />
Using the and keys, or the appropriate<br />
number, make your selection from the list e.g. 1 SLOGAN<br />
and press to confirm, the SLOGAN screen will be<br />
observed.<br />
If a Slogan is already selected, that slogan will be highlighted.<br />
Obsolete Product<br />
Using the and keys, or the appropriate<br />
number, make your selection from the list, press<br />
confirm.<br />
If you wish to retain the current selection, press the<br />
key to return to the IMPRINT menu screen.<br />
Continued on the next page.<br />
to<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 25
HASLER Printing Section 3<br />
To return to Ready Mode screen press .<br />
The Icon displayed in the top left hand corner of the screen<br />
indicates that a slogan has been selected.<br />
Date Advance (for Pre Dating Mail)<br />
Your machine is fitted with its own calendar/clock, therefore<br />
current date setting is automatic. If you wish to prepare mail<br />
ahead of time it is possible to advance the posting date by up<br />
to seven days.<br />
Obsolete Product<br />
From the IMPRINT screen select DATE ADVANCE, the<br />
following screen will be observed:<br />
1 09/19/02<br />
2 09/20/02<br />
3 09/21/02<br />
4 09/22/02<br />
Next, using the and keys, select from the list<br />
the date on which you wish to post your mail.<br />
Press<br />
to confirm and return to the IMPRINT screen.<br />
Continued on the next page.<br />
Page 3 - 26 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
To return to Ready Mode with the Advanced Postage Date<br />
displayed, press .<br />
You Are Now Ready To Print Your Predated Mail<br />
On completion of your pre dated mail run, your meter MUST<br />
be reset to the current date.<br />
However, if the Timeout period is exceeded, your<br />
meter will go to Standby and the Date Advance<br />
setting be automatically cancelled.<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 27
HASLER Printing Section 3<br />
Maintaining Print Quality<br />
Under normal operating conditions, your <strong>WJ60</strong>/<strong>WJ90</strong> postage<br />
meter will produce excellent quality prints. However, if lines<br />
are missing from the stamp or the machine has remained<br />
unused for several days it will be necessary to clean the Ink<br />
Cartridge.<br />
Cleaning the Ink Cartridge<br />
From Ready Mode, press the<br />
screen will now be observed:<br />
key, the MAIN MENU<br />
1 REGISTERS<br />
2 CARTRIDGE<br />
3 SUPERVISOR<br />
4 CLEAR MAIL PATH<br />
Obsolete Product<br />
Using the and keys, or the appropriate<br />
number key, move the cursor to CARTRIDGE and press<br />
to confirm. The CARTRIDGE menu will now be<br />
observed:<br />
1 TEST PRINT<br />
2 CLEAN<br />
3 REMOVE<br />
Select the CLEAN option from the list and press to<br />
start the cleaning cycle.<br />
On completion of the cleaning cycle the screen will revert to<br />
the CARTRIDGE menu.<br />
You must now make a test print.<br />
Page 3 - 28 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
Making a Test Print<br />
Select the TEST PRINT option from the CARTRIDGE menu<br />
and press<br />
to confirm.<br />
1 TEST PRINT<br />
2 CLEAN<br />
3 REMOVE<br />
The prompt to produce a Test Print will now displayed.<br />
To make a Test Print, insert a blank envelope or card and<br />
TEST PRINT<br />
09/20/02<br />
Obsolete Product<br />
press<br />
and present.<br />
. Inspect the Test Print to ensure that all lines are clear<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 29
HASLER Printing Section 3<br />
To set the alignment, enter the number that provides the<br />
straightest line (for the example above line 5) by pressing the<br />
appropriate numeric key on the keypad.<br />
ENTER STRAIGHTEST LINE NO.<br />
5<br />
Press to confirm. If any lines are missing, repeat the<br />
cleaning and test print process up to three times, if this<br />
process fails to restore print quality, install a new ink<br />
cartridge.<br />
Obsolete Product<br />
If the test print is satisfactory, press<br />
twice to<br />
return to Ready Mode.<br />
Page 3 - 30 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
Low Ink<br />
Should the ink cartridge require replacing, the LOW<br />
INK display will be observed:<br />
You have approximately 200 printing operations available,<br />
after which the Ink Cartridge MUST be replaced.<br />
No Ink<br />
When the NO INK display is observed, printing is disabled and<br />
the Ink Cartridge MUST be replaced before any franking<br />
operations can be resumed.<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 31
HASLER Printing Section 3<br />
Replacing an Ink Cartridge<br />
Select the REMOVE option from the CARTRIDGE menu:<br />
1 TEST PRINT<br />
2 CLEAN<br />
3 REMOVE<br />
Press to confirm.<br />
After a short time, the following screen will be observed:<br />
CARTRIDGE<br />
INSERT CARTRIDGE AND PRESS OK<br />
Obsolete Product<br />
Open the<br />
machine top<br />
cover.<br />
Press on the<br />
front of the<br />
Ink Cartridge<br />
as shown in<br />
order to<br />
remove it.<br />
Continued on the next page.<br />
Page 3 - 32 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Printing Postage Section 3<br />
Carefully withdraw the used Ink Cartridge and discard.<br />
Remove the new Ink Cartridge from its packaging and<br />
carefully remove the tape seals.<br />
Do NOT touch or remove the copper strip on Ink<br />
Cartridges.<br />
Obsolete Product<br />
Place the new cartridge into its holder, and lock it in position<br />
by carefully pushing down on the depressed circle on top of<br />
the cartridge with your index finger, then using your thumb to<br />
push the rear of the ink cartridge in the direction illustrated.<br />
Close the machine top cover and press .<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 3 - 33
HASLER Printing Section 3<br />
After a short delay the prompt to make a Test Print will be<br />
observed:<br />
TEST PRINT<br />
09/19/02<br />
Please refer to Making a Test Print on in this section.<br />
Your <strong>WJ60</strong>/<strong>WJ90</strong> is supplied with a complimentary short life<br />
cartridge. You should order your next standard cartridge from<br />
<strong>Hasler</strong> or your local <strong>Hasler</strong> Dealer.<br />
Obsolete Product<br />
Complimentary short life<br />
cartridge approximately 12,500<br />
impressions<br />
Standard cartridge<br />
approximately 17,000<br />
impressions<br />
Page 3 - 34 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Moistener Section 4<br />
Your <strong>WJ60</strong>/<strong>WJ90</strong> Postage Meter used in conjunction with a<br />
Moistener Unit will seal and print envelopes in a single<br />
operation.<br />
• The moistener may be set to non-seal mode if sealing is<br />
not required enabling the unit to be used as a normal feed<br />
platform.<br />
• If seal only is required, the postage meter mode may be<br />
set to SEAL ONLY (please refer to PRINTING OPTIONS).<br />
• The Moistener Unit may be used with an Autofeed Unit or<br />
with the Hand Feed Platform.<br />
Using the Envelope Moistener with Plain Platform 4-1<br />
Using the Envelope Moistener with an Autofeed 4-2<br />
Filling the Reservoir 4-2<br />
Obsolete Product<br />
Using the Envelope Moistener with Plain Platform<br />
Set the Moistener ON/OFF control to (ON).<br />
Press the<br />
start.<br />
button, after a short pause the motor will<br />
Each envelope must be fed into the moistener unit with the<br />
flap downwards and top edge against the platform mail guide.<br />
Particular attention should be paid to keeping the envelope<br />
flat.<br />
A continuous sliding action is made until the envelope<br />
contacts the postage meter rollers. The envelope will be<br />
drawn through the postage meter and deposited into the<br />
receiving tray.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 4-1
HASLER Moistener Section 4<br />
Using the Envelope Moistener with an Autofeed<br />
Set the Moistener ON/OFF control to ON [ ].<br />
Load the Autofeed Platform as detailed in Printing Postage<br />
Section 3.<br />
Press the button, after a short pause the motor will start<br />
and sealed envelopes will be deposited into the receiving tray.<br />
Filling the reservoir<br />
For safety, always disconnect the postage meter from<br />
the power supply when filling the moistener reservoir,<br />
keep the postage meter top cover closed and take<br />
care not to spill sealing solution onto the machine.<br />
Obsolete Product<br />
Disconnect the unit from the power supply<br />
Open the reservoir compartment and fill with <strong>Hasler</strong> sealing<br />
solution.<br />
Close the reservoir compartment.<br />
CAUTION<br />
If sealing solution is spilt and enters the postage meter<br />
mechanism, DO NOT reconnect the machine to the<br />
power supply, DO NOT attempt to remove the machine<br />
covers, CONTACT YOUR LOCAL HASLER DEALER.<br />
Page 4 - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Meter Registers Section 5<br />
Your postage meter is equipped with a series of<br />
electronic registers to monitor franking transactions.<br />
A number of departments are available in which<br />
separate registers showing postage used and items<br />
printed are stored.<br />
Sample Register Displays 5-1<br />
Meter Register Selection 5-2<br />
Printing a Register 5-4<br />
Printing Registers with External Printer 5-5<br />
The values of these registers may be displayed and<br />
printed as follows.<br />
Main Registers<br />
All register values illustrated are typical:<br />
SUMMARY REPORT<br />
DESCENDING 150.20<br />
ASCENDING 749.70<br />
POST OFFICE ITEMS 540<br />
Obsolete Product<br />
DESCENDING = postage available, ASCENDING = postage used<br />
Postage Set<br />
All register values illustrated are typical:<br />
POSTAGE SET REPORT<br />
PREVIOUS DESCENDING 50.20<br />
AMOUNT PURCHASED 100.00<br />
NEW DESCENDING 150.20<br />
NEW CONTROL TOTAL 900.00<br />
TRANSACTION DATE 01/15/02<br />
Continued on the next page.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 5 - 1
HASLER Meter Registers Section 5<br />
Department Registers<br />
All register values illustrated are typical:<br />
DEPT NAME<br />
MARKETING<br />
TOTAL 25.67<br />
ITEMS 75<br />
LAST RESET 09/05/02<br />
Meter Register Selection<br />
To select a Meter Register from Ready Mode, press the<br />
key, the following screen will be observed:<br />
Obsolete Product<br />
1 REGISTERS<br />
2 CARTRIDGE<br />
3 SUPERVISOR<br />
4 CLEAR MAIL PATH<br />
Using the and keys, or the appropriate<br />
number key, move the cursor to REGISTERS and press<br />
to confirm, the list of registers available to view will<br />
now be displayed:<br />
1 MAIN REGISTERS<br />
2 POSTAGE SET<br />
3 DEPARTMENT REGISTERS<br />
Continued on the next page.<br />
Page 5 - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Meter Registers Section 5<br />
Using the and keys, or the appropriate<br />
number key, select a register option from the list then press<br />
to confirm.<br />
Example: DEPARTMENT REGISTERS:<br />
DEPT NAME<br />
MARKETING<br />
TOTAL 25.67<br />
ITEMS 75<br />
LAST RESET 09/05/02<br />
Current Department Displayed.<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 5 - 3
HASLER Meter Registers Section 5<br />
Printing a Register<br />
To print a register press , if the method of print is<br />
set to Internal, the following screen will be observed:<br />
After a few seconds, your register data will be printed on a<br />
label and you will be returned to the DEPARTMENT<br />
REGISTERS screen.<br />
If during the printing process the following display is observed:<br />
Obsolete Product<br />
First replenish the label dispenser then press<br />
to complete the report printing process.<br />
If after a short wait, you are returned to the register screen<br />
your method of print may be set to External Printer, please<br />
refer to Printing with External Printer below.<br />
Note: The method of print (Label or External Printer) is set in<br />
Supervisor Mode.<br />
Continued on the next page.<br />
Page 5 - 4 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Meter Registers Section 5<br />
Press<br />
to return to the REGISTERS screen.<br />
To return to Ready Mode press<br />
twice.<br />
Printing Registers with External Printer<br />
Before proceeding to print registers using an external<br />
printer ensure that the printer lead is connected to<br />
the Upper Accessory Port at the back of the machine,<br />
and that the printer power lead is connected to an<br />
adjacent power outlet.<br />
Set the printer to ON and the status to ONLINE.<br />
From your selected registers screen press ,<br />
after a short period of time, you will be returned to the<br />
screen and the register data will have been printed.<br />
Obsolete Product<br />
If the registers screen does not re-appear after a few<br />
seconds and the printer does not print, re-check all<br />
printer connections and ensure that the printer status<br />
is set to ONLINE.<br />
The external printer must be a serial printer and set<br />
as follows: Baud Rate - 9600, Data Bits - 8, Stop Bits<br />
- 1, Parity - None.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 5 - 5
This page intentionally left blank.<br />
Obsolete Product
HASLER Adding Postage Section 6<br />
Postage may be purchased from the Post Office, using the<br />
<strong>Hasler</strong> TMS® (Tele-Metering-System).<br />
TMS ® (Tele Meter Setting) permits the loading of postage<br />
funds into the <strong>WJ60</strong>/<strong>WJ90</strong> over a standard analog telephone<br />
line. Prior to printing indicia tapes, your <strong>Hasler</strong> <strong>WJ60</strong>/<strong>WJ90</strong><br />
must be loaded with funds.<br />
<strong>Hasler</strong>’s TMS ® (Tele Meter Setting) provides the means to<br />
download funds from your TMS ® Bank Account. With TMS ® ,<br />
you maintain a TMS ® Bank Account into which you deposit<br />
money for postage by either mailing a check to <strong>Hasler</strong> or by<br />
automatically debiting an account that you designate. These<br />
funds are deposited into your TMS ® Bank Account and are<br />
then available to download at any time into the <strong>WJ60</strong>/<strong>WJ90</strong>.<br />
Obsolete Product<br />
Modem Connection 6-2<br />
Adding Postage 6-2<br />
‘WARNING PENDING CREDIT’ Procedure 6-3<br />
Clearing A PO Lockout 6-4<br />
Maintaining Your TMS Account Number 6-5<br />
TMS Account Number 6-5<br />
TMS Account Balance 6-5<br />
TMS Statements 6-6<br />
Post Office Regulations 6-6<br />
PostageNow 6-7<br />
PostageNow TeleFunds 6-8<br />
PostageNow OnDemand 6-8<br />
Information whenever you want it online or by phone 6-8<br />
Managing Your Account 6-9<br />
Standard TMS Bank Accounts 6-10<br />
Where To Mail Your TMS Bank Account Deposit 6-11<br />
Contact Information 6-12<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 6 - 1
HASLER Adding Postage Section 6<br />
Modem Connection<br />
Connect one end of the telephone link cable to the Modem<br />
Socket ( ) at the rear of the machine and the other end to an<br />
adjacent telephone line outlet. The meter only requires the<br />
connection to the telephone line outlet during the Add Postage<br />
or Clear Lockout transaction. The modem dial-up phone<br />
number is 1-800-446-6029.<br />
Adding Postage<br />
From Ready Mode, press .<br />
The ENTER AMOUNT screen will be observed.<br />
ENTER AMOUNT<br />
$0.00<br />
Obsolete Product<br />
Using the numeric keypad, enter the amount of postage you<br />
wish to purchase (whole dollars only), example: 100.<br />
Press: , , and to confirm.<br />
You will now be asked to verify the amount before proceeding.<br />
CONFIRM AMOUNT<br />
$100.00<br />
Continued on the next page.<br />
Page 6 - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Adding Postage Section 6<br />
If the amount is incorrect, press<br />
from the Enter Amount screen.<br />
If the amount displayed is correct, press<br />
and start again<br />
to confirm.<br />
The display will show Dialing … Transacting … and on<br />
completion of the ADD POSTAGE transaction, the following<br />
screen will be observed:<br />
FUNDING DONE<br />
$100.00<br />
Press<br />
to exit.<br />
Obsolete Product<br />
‘WARNING PENDING CREDIT’ Procedure<br />
Completing an Interrupted Add Postage Transaction:<br />
If an Add Postage transaction is accidentally interrupted<br />
before the transfer has been completed, the WARNING<br />
PENDING CREDIT screen will be observed when returning<br />
from Locked mode after the machine has been unplugged.<br />
WARNING<br />
PENDING CREDIT<br />
In this case, press<br />
to return to Ready Mode.<br />
Continued on the next page.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 6 - 3
HASLER Adding Postage Section 6<br />
Press the FUNDS key to automatically finish the<br />
incomplete transaction.<br />
On completion of the Add Postage transaction, press<br />
to return to Ready Mode.<br />
Clearing A PO Lockout<br />
USPS regulations require that your meter must be set at least<br />
once every three months. The meter has an internal timer<br />
that tracks your reset activity. After three months without<br />
adding postage, a PO LOCKOUT message is displayed and<br />
postage printing is disabled.<br />
To clear the lockout:<br />
Obsolete<br />
WARNING<br />
PO LOCKOUT<br />
Product<br />
PRESS FUNDS KEY<br />
In this case, press to return to Ready Mode .<br />
Press the FUNDS key to automatically clear the PO<br />
Lockout.<br />
On completion of the Clear PO Lockout transaction, press<br />
to return to Ready Mode.<br />
Note: The machine only requires connection to the<br />
telephone line outlet during the Add Postage and Clear<br />
Lock-Out transaction.<br />
Page 6 - 4 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Adding Postage Section 6<br />
Maintaining Your TMS Account Number<br />
TMS Account Number<br />
After you sign a rental agreement for your meter, you will be<br />
assigned a TMS® (Tele Meter Setting) Bank Account<br />
Number. An account confirmation Welcome Letter will be<br />
mailed to you indicating your TMS® Bank Account Number<br />
and your Mailer Agreement Number. These number should<br />
be kept in a safe place, yet be readily available, because they<br />
are used for all TMS® account maintenance transactions.<br />
TMS Account Balance<br />
You can use the <strong>Hasler</strong> Automated TMS system to check<br />
your bank account status and other important TMS<br />
information. Simply call 1-800-248-8013 and use your<br />
touchtone phone to enter your TMS Bank Account Number<br />
and your Mailer Agreement Number. Then select from the<br />
menu options.<br />
Obsolete Product<br />
You can also go online to (1) www.infonowonline.com or (2)<br />
www.haslerinc.com and select Postage Accounts (TMS). You<br />
will need to enter TMS Bank Account Number and your Mailer<br />
Agreement Number. Then select from the menu options.<br />
With either system, you can learn details regarding your<br />
Account Balance (includes the current balance, the available<br />
balance and any unpaid advances). You can also receive<br />
information on holiday schedules, meter operating guides,<br />
licensing forms, payment addresses, and customized TMS<br />
Bank Account statements.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 6 - 5
HASLER Adding Postage Section 6<br />
Statements<br />
You can receive a daily, weekly, monthly, or quarterly<br />
statement of all activity in your TMS Bank Account. To be<br />
setup on Automatic Statements you must make a request by<br />
fax (203-925-5464) or by calling (1-800-248-8013). This<br />
statement includes deposits, remote meter settings,<br />
transaction fees and the ending account balance.<br />
Notes:<br />
a. If there is no account activity you will not receive a<br />
statement.<br />
b. You can request statements to be emailed or faxed<br />
automatically to your location.<br />
You can request statements for customized time periods by<br />
visiting our web site at www.haslerinc.com or<br />
www.infonowonline.com and selecting Postage Account<br />
Quicklink.<br />
Obsolete Product<br />
Post Office Regulations<br />
United States Postal Service regulations require that your<br />
meter must be audited at regular intervals (currently set at<br />
109 days). For your convenience an audit is automatically<br />
performed each time you add postage or do a "zero" reset<br />
(load $0.00 funds).<br />
If you do not add postage or perform an audit within the 109-<br />
day period, a “TIME LIMIT REACHED” message is displayed<br />
on the meter and postage printing is disabled.<br />
To clear the lockout, simply press the [C] key to clear the<br />
message and do an "audit" or do a TMS postage load via<br />
modem connection. When the transaction is completed,<br />
postage printing is enabled for another 109 days.<br />
Page 6 - 6 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Adding Postage Section 6<br />
Postage Now<br />
Get the postage you need, when you need it, without having to<br />
call ahead of time. Postage Now, a service of the United<br />
States Postal Service, gives you the option to seamlessly<br />
fund your postage needs simply by setting your postage<br />
meter. TMS fax back form<br />
Postage whenever you need it<br />
With PostageNow TeleFunds last-minute mailings are<br />
no longer a problem. Now, you can have immediate access to<br />
additional postage funds simply by setting your meter!<br />
Postage funds will automatically be debited from your<br />
specified corporate bank account, usually the next business<br />
day, but the postage is immediately provided by the USPS. No<br />
pre-funding required.<br />
No processing fees with PostageNow TeleFunds.<br />
Choosing seamless postage funds availability with<br />
PostageNow TeleFunds means you won’t have to<br />
maintain<br />
Obsolete<br />
a minimum balance in your<br />
Product<br />
TMS Bank Account. And,<br />
with PostageNow TeleFunds, there’s never a transfer<br />
processing<br />
fee—ever.<br />
To begin using PostageNow TeleFunds, simply fill out the<br />
ACH Customer Authorization and Agreement form, check<br />
the PostageNow TeleFunds option, and fax the form with<br />
a voided check. There is a one-time, $15 set-up fee for<br />
new accounts.<br />
Control your postage access<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 6 - 7
HASLER Adding Postage Section 6<br />
PostageNow OnDemand<br />
If you prefer to have more control over your postage, you<br />
may choose instead to call ahead to debit a specified<br />
amount of postage funds from your corporate bank account<br />
with PostageNow OnDemand.<br />
The PostageNow OnDemand option can only be accessed<br />
during the operating hours of the TMS Center (listed on the<br />
back of this brochure). There will be a $5 processing fee<br />
each time you call to debit funds.<br />
To begin using PostageNow OnDemand, simply fill out the<br />
ACH Customer Authorization and Agreement form, check<br />
the PostageNow OnDemand option, and fax the form with<br />
a voided check. There is a one-time, $15 set-up fee for<br />
new accounts.<br />
Obsolete Product<br />
Information whenever you want it online or by phone<br />
Now TMS customers can access all kinds of information<br />
at <strong>Hasler</strong>’s new TMS website. Simply log on to<br />
www.InfoNowOnline.com for previous business day TMS<br />
bank account balances, holiday schedules, meter operating<br />
guides, licensing forms, and payment addresses.<br />
You may also request a customized TMS bank account<br />
statement from any time period that you can receive by email<br />
or fax, and order payment coupons.<br />
You also have the option to get the same information by<br />
phone, using <strong>Hasler</strong>’s new easy-to-use, interactive service,<br />
InfoNow®. The number is 1-800-248-8013.<br />
For security purposes, you’ll need to have your TMS bank<br />
account number and your mailer agreement number handy<br />
when using either InfoNow or InfoNow Online.<br />
Automated statements<br />
Page 6 - 8 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Adding Postage Section 6<br />
Managing Your Account<br />
We’ve made managing your TMS bank account even easier.<br />
Now you can choose to receive automated statements on a<br />
schedule that works best for your workflow. Daily, weekly,<br />
monthly or quarterly. Choose to receive your statements by<br />
fax or email, whichever is most convenient for you.<br />
In addition, you can always access your account information<br />
whenever you want by logging on to the TMS website,<br />
www.infonowonline.com or calling <strong>Hasler</strong>’s automated<br />
phone service, InfoNow, at 800-248-8013.<br />
Call 800/248-8013 or visit www.Infonowonline.com<br />
anytime for information.<br />
What is ACH?<br />
Obsolete Product<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 6 - 9
HASLER Adding Postage Section 6<br />
Standard TMS Bank Accounts<br />
Standard TMS Bank Accounts are pre-funded and require that<br />
money be in your TMS Bank Account to add postage to your<br />
meter. After using the TMS system to add money to your<br />
meter, your account decreases by the amount of the postage<br />
added. Remember to deposit sufficient funds to cover your<br />
planned setting withdrawals.<br />
Upon receipt of the check, your TMS Bank Account will be<br />
credited with your deposit (allow 7 to 10 business days for the<br />
check to be received and posted).<br />
Make your check out to United States Postal Service, and<br />
write your TMS Bank Account on the check.<br />
Always enclose your USPS provided Coupon with your<br />
check. This will assure the fastest and most accurate bank<br />
processing.<br />
Obsolete<br />
You will receive a package<br />
Product<br />
of coupons in the<br />
mail shortly after setting up your TMS® Bank Account.<br />
Replacements are re-ordered automatically when you submit<br />
your 8th coupon with your check.<br />
Page 6 - 10 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Adding Postage Section 6<br />
Where To Mail Your TMS Bank Account Deposit<br />
There are three regional USPS Trust Account Lock Boxes to<br />
facilitate faster receipt of your deposit checks: PA -<br />
Pennsylvania, IL - Illinois and CA - California.<br />
USPS Trust Account Regional Remittance Lock Boxes<br />
PA IL CA<br />
Regular Mail Regular Mail Regular Mail<br />
CMRS-TMS CMRS-TMS CMRS-TMS<br />
P.O. Box 7247-0217 P.O. Box 0527 P.O. Box 894757<br />
Philadelphia, PA Carol Stream, IL Los Angeles, CA<br />
19170-0217 60132-0527 90189-4757<br />
Overnight Delivery<br />
Attn:Team One - TMS<br />
Citibank Lockbox #0217<br />
1615 Brett Road<br />
New Castle, DE 19720<br />
Obsolete Product<br />
Wire Transfers<br />
Citibank, 111 Wall St., New York, NY 10043<br />
ABA Routing # 021000089<br />
CMRS / <strong>Hasler</strong><br />
Account # 4067-8617<br />
Detail Payment Field: TMS Bank Account # (include it to ensure<br />
credit for your transfer).<br />
ACH Transfers<br />
Citibank, 111 Wall St., New York, NY 10043<br />
ABA Routing # 021000089<br />
CMRS / <strong>Hasler</strong><br />
Account # 4067-8617<br />
Type: CCD/CCD+TMS Bank Account # in positions 40 through 47.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 6 - 11
HASLER Adding Postage Section 6<br />
Contact Information<br />
<strong>Hasler</strong> ® , <strong>Inc</strong>.<br />
19 Forest Parkway<br />
Shelton, CT 06484-6140<br />
www.haslerinc.com<br />
Customer Service Helpdesk<br />
1-800-243-6275<br />
Call for customer service or for your local dealer telephone<br />
number for technical support. The Customer Service<br />
Helpdesk can also direct you on where to obtain supplies for<br />
your <strong>Hasler</strong> mailing system.<br />
TMS ® Automated Account Information<br />
1-800-248-8013<br />
Call to check Account Balance, or other account information<br />
via touch-tone telephone. You can also talk to a customer<br />
service representative using this number.<br />
Obsolete Product<br />
TMS ® Automated Account Information Online<br />
(1) www.infonowonline.com or (2) www.haslerinc.com and<br />
select Postage Accounts (TMS).<br />
It is an online site that can answer all your details regarding<br />
your Account Balance. You can also receive information on<br />
holiday schedules, meter operating guides, licensing forms,<br />
payment addresses, and customized TMS Bank Account<br />
statements.<br />
TMS ® Modem Telephone Number<br />
1-800-446-6029<br />
Modem telephone number set up in meter.<br />
Page 6 - 12 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Memory Functions Section 7<br />
Frequently used print combinations may be pre-programmed<br />
as a memory function with five preset memory slots available<br />
for selection.<br />
Saving A Memory Function 7-1<br />
Recalling A Memory Function 7-3<br />
Saving a Memory Function<br />
Setup your preferred print combination, then press the<br />
key twice (pressing once shows Memory Recall screen<br />
instead of Memory Save screen), the following screen will<br />
now be observed:<br />
Obsolete Product<br />
Select the Job Memory in which you wish to save your<br />
program and press to confirm. You will then be<br />
prompted to enter a name for your Job Memory.<br />
Continued on the next page.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 7 - 1
HASLER Memory Functions Section 7<br />
Use the , and keys to move the<br />
cursor to the character to be defined.<br />
The key is used to confirm selection and move the<br />
cursor to the next character.<br />
To delete a character press .<br />
Obsolete Product<br />
To enter a number in the Memory Name use the numeric<br />
keypad.<br />
To return to the previous screen with the Memory Name<br />
unchanged press .<br />
To confirm your entry press .<br />
This operation will overwrite the previous memory setting.<br />
To return to Ready Mode press .<br />
Page 7 - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Memory Functions Section 7<br />
Recalling a Memory Function<br />
From Ready Mode, press the key once (pressing the<br />
key twice brings the Memory Save screen instead of the<br />
Memory Recall screen) to display the JOB MEMORY screen:<br />
Select<br />
Obsolete<br />
option 1 MEMORY RECALL<br />
Product<br />
and press to<br />
confirm, a list of memories will now be observed:<br />
Using the key or the appropriate numerical key,<br />
move the cursor to make your memory recall selection.<br />
To confirm your selection, press .<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 7 - 3
This page intentionally left blank.<br />
Obsolete Product
HASLER Supervisor Settings Section 8<br />
In Supervisor Mode, the supervisor can access all machine<br />
functions, except franking. Navigation procedure from screen<br />
to screen is the same as in the user mode, except that the<br />
supervisor mode includes a number of extra configuration<br />
function keys.<br />
By definition, the supervisor has free access to all the<br />
departments and as such he/she is not prompted by the<br />
machine to enter any code after the Supervisor Code has<br />
been entered. For security purposes, only a supervisor or<br />
other responsible person should be permitted to make<br />
changes to these settings.<br />
Entry to Supervisor Mode 8-2<br />
Departments Control 8-4<br />
Changing the User PIN 8-5<br />
Setting the User Status 8-6<br />
To Assign a Department 8-7<br />
To Change a Department Name 8-9<br />
Department Code 8-10<br />
To Change the Department Status 8-11<br />
To Reset the Department Registers 8-11<br />
<strong>WJ60</strong>/<strong>WJ90</strong> Machine Setup Menu 8-12<br />
Machine Setup 8-14<br />
High Value 8-14<br />
Low Credit 8-15<br />
Time 8-16<br />
Sleep Mode 8-17<br />
Key Beep 8-17<br />
Default Stamp Value 8-18<br />
Registration (Change Address, Audit, Withdraw) 8-19<br />
Telephone Settings 8-20<br />
Memory (Rate / Slogan) Cards 8-22<br />
How To Replace Data Using a Memory Card 8-24<br />
Text Messages 8-26<br />
Reports / Printing A Report 8-28<br />
Setting the Report Destination 8-30<br />
Printing with External Printer 8-31<br />
Obsolete Product<br />
The Supervisor Password is 9430.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 1
HASLER Supervisor Settings Section 8<br />
Entry to Supervisor Mode<br />
To enter SUPERVISOR mode from the Standby screen:<br />
Press the<br />
key.<br />
Or from the MAIN MENU in USER Mode by selecting<br />
SUPERVISOR. The prompt to ENTER SUPERVISOR PIN will<br />
be observed:<br />
Obsolete Product<br />
ENTER SUPERVISOR PIN<br />
- - - -<br />
Enter the Supervisor PIN … 9430.<br />
If an incorrect PIN is entered the machine will continue to<br />
prompt for SUPERVISOR PIN Entry until the correct PIN is<br />
used.<br />
Continued on the next page.<br />
Page 8 - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
Having successfully entered Supervisor Mode, the<br />
SUPERVISOR screen will be observed:<br />
The following functions may be accessed directly from the<br />
Supervisor Ready screen:<br />
SECURITY & DEPT:allows the supervisor to access the<br />
department setup and security functions.<br />
REGISTERS: provides access to registers<br />
Obsolete Product<br />
TEXT: enables supervisor to set personalized messages.<br />
LOAD FROM MEMORY CARD: enables supervisor to enter<br />
data to the machine memory e.g. Advert Cards, Rate Cards<br />
(When postal rates change) and Town Cards (When you<br />
change location).<br />
SETUP: allows access to machine setup.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 3
HASLER Supervisor Settings Section 8<br />
Departments Control<br />
• In Non-Departmental <strong>Operating</strong> mode, all values are<br />
assigned to Department 0.<br />
• In Departmental mode <strong>WJ60</strong> has 35 departments,<br />
while <strong>WJ90</strong> has 45 departments, available for<br />
assignment by the supervisor.<br />
From the SUPERVISOR menu, move the cursor to option 1<br />
SECURITY & DEPT. Press<br />
The following screen will now be observed:<br />
SECURITY & DEPT<br />
to confirm.<br />
1 STATUS DISABLED<br />
2 SET UP DEPT<br />
3 DEPTMENT SELECTION PICK FROM LIST<br />
4 LAST RESET ALL DEPT 00/00/00<br />
5<br />
Obsolete<br />
USER PIN 0000<br />
Product<br />
The following functions may be accessed directly from the<br />
Departments Control screen:<br />
STATUS: allows supervisor to enable Departmental<br />
operation.<br />
USER PIN: allows supervisor to set the 4-digit User PIN.<br />
USER STATUS: allows supervisor to set the User Status.<br />
LAST RESET ALL DEPT: allows supervisor to reset All<br />
Registers to zero.<br />
SET UP DEPT: allows supervisor to setup Departments.<br />
When in Departmental <strong>Operating</strong> Mode access to<br />
Non-Departmental <strong>Operating</strong> Mode (Department 0)<br />
is disabled.<br />
Page 8 - 4 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
Changing the User PIN<br />
Using the and keys, or the appropriate<br />
number key, move the cursor to 2 USER PIN and press<br />
to confirm, the following screen will be observed:<br />
USER PIN<br />
- - - - -<br />
To return to the previous screen with the User PIN<br />
unchanged, press .<br />
Obsolete Product<br />
To change the User PIN, enter the new 4 digit value, then<br />
press to confirm.<br />
To return to the SUPERVISOR screen press .<br />
The User Pin allows anyone that has the code<br />
access to the department.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 5
HASLER Supervisor Settings Section 8<br />
Setting the User Status<br />
Using the and keys, or the appropriate<br />
number key, move the cursor to 3 USER STATUS and press<br />
to confirm, the following screen will be observed:<br />
To return to the previous screen with the User Status<br />
unchanged, press .<br />
Obsolete Product<br />
Using the and keys, or the appropriate<br />
number key, make your selection and press<br />
confirm.<br />
To return to the SUPERVISOR screen press .<br />
to<br />
Closed = Users will not see the related department as a<br />
choice.<br />
Open = Users will see the related department as a choice.<br />
Locked = User has entered an incorrect access code 8<br />
times and has been locked out. Call the supervisor.<br />
Example: there are 3 departments: 1, 2, and 3. The users<br />
are closed for department 1. The users will only see<br />
departments 2 and 3 for departmental choices.<br />
Page 8 - 6 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
To Assign a Department<br />
From the SECURITY & DEPT menu, move the cursor to<br />
STATUS. Press<br />
will be observed:<br />
to confirm. The following screen<br />
1 DISABLED<br />
2 ENABLED<br />
Using the and keys, or the appropriate<br />
number key, move the cursor to ENABLED and press<br />
Obsolete Product<br />
to confirm, you will be returned to the<br />
SECURITY & DEPT screen with the status changed<br />
to ENABLED.<br />
SECURITY & DEPT<br />
1 STATUS ENABLED<br />
2 SET UP DEPT<br />
3 DEPTMENT SELECTION PICK FROM LIST<br />
4 LAST RESET ALL DEPT 00/00/00<br />
5 USER PIN 0000<br />
Using the and keys, or the appropriate<br />
number key, move the cursor to SET UP DEPT and<br />
press<br />
to confirm.<br />
Continued on the next page.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 7
HASLER Supervisor Settings Section 8<br />
The following screen will be observed:<br />
Again using the and keys, or the appropriate<br />
number key, move the cursor to the Number you wish to set<br />
and press to confirm, the DEPARTMENT<br />
SETTINGS screen for the selected department will be<br />
observed:<br />
Obsolete Product<br />
To set a Department Name, move the cursor to DEPT NAME and<br />
press to confirm, the following screen will be observed:<br />
Use the , and keys to move<br />
the cursor to the character to be defined.<br />
Page 8 - 8 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
The key is used to confirm the selection and move<br />
the cursor to the next character. To delete a character press<br />
.<br />
To enter numbers in the text use the numeric keypad, you do<br />
not need to press the<br />
when entering numbers.<br />
key to confirm selection<br />
A department name is limited to 16 characters including<br />
spaces.<br />
To return to the previous screen with the Department Name<br />
unchanged press<br />
until the screen changes to the<br />
previous one. To confirm your entry press .<br />
Obsolete Product<br />
To Change a Department Name , select DEPT NAME as<br />
described above.<br />
Using the<br />
key, delete characters of the old Department<br />
Name. Press as many times as required to erase the<br />
Department Name completely, then enter the new name as<br />
previously detailed.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 9
HASLER Supervisor Settings Section 8<br />
Department Code<br />
To set a Department Code move the cursor to DEPT CODE<br />
and press to confirm, the following screen will be<br />
observed:<br />
Using the numerical keypad enter/change the account<br />
number, press to confirm.<br />
To return to the previous screen with account number<br />
unchanged press .<br />
To<br />
Obsolete<br />
set a Department PIN, move the<br />
Product<br />
cursor to DEPT PIN and<br />
press to confirm, the following screen will be<br />
observed:<br />
DEPT PIN<br />
- - - - -<br />
To change the Department PIN, enter the new value, then<br />
press to confirm.<br />
To return to the previous screen with the Department PIN<br />
unchanged, press .<br />
Page 8 - 10 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
To Change the Department Status, move the cursor to<br />
STATUS and press to confirm, the following<br />
screen will be observed:<br />
1 CLOSED<br />
2 OPEN<br />
3 LOCKED<br />
Using the and keys, or the appropriate<br />
number key, move the cursor to OPEN and press<br />
to confirm.<br />
Obsolete Product<br />
To Reset the Department Registers, move the cursor to<br />
LAST RESET and press<br />
screen will be observed:<br />
to confirm, the following<br />
DEPT DATA WILL BE ERAZED!<br />
To return to the previous screen with data unchanged, press<br />
.<br />
To reset current Department Data to zero, press<br />
to confirm.<br />
Continued on the next page.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 11
HASLER Supervisor Settings Section 8<br />
The following screen will now be observed with the current<br />
date displayed as LAST RESET:<br />
Your Department is assigned and ready for use.<br />
To return to the SUPERVISOR screen press .<br />
<strong>WJ60</strong>/<strong>WJ90</strong> Machine Setup Menu<br />
The<br />
Obsolete<br />
SETUP menu provides access<br />
Product<br />
to the following<br />
supervisor functions :<br />
1. High Value<br />
A High Value Warning will be displayed in User Mode when a<br />
value exceeding or equal to the High Value threshold is<br />
selected, this value may be changed. (Default High Value set<br />
to $1.00)<br />
2. Low Credit<br />
The Low Credit Warning will be displayed in User Mode when<br />
the credit level falls below or equal to the Low Credit<br />
threshold, this value may be changed. (Default Low Credit<br />
value set to $50.00)<br />
3. Time<br />
The machine clock is set to local time, the year cannot be<br />
changed, however to facilitate Summer/Winter time changes<br />
the time can be changed.<br />
Continued on the next page.<br />
Page 8 - 12 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
4. Sleep Mode<br />
If the machine is left for a period of time it will automatically<br />
return to Sleep Mode. To change the time out see Sleep<br />
Mode. (Default Sleep Mode time out set to 5 minutes)<br />
5. Motor Timeout<br />
Controls the length of time the motors run after processing<br />
the last item of mail. Short is approximately 5 seconds,<br />
Medium is approximately 15 seconds, and Long is<br />
approximately 30 seconds.<br />
6. Key Beep<br />
May be set to sound when a key is pressed, this setting may<br />
be changed. (Default set to ON)<br />
7. Default Stamp Value<br />
Enables the supervisor to define a default postage value.<br />
(Default Stamp Value set to $0.00)<br />
8. Telephone Settings<br />
The telephone numbers of the <strong>Hasler</strong> TMS Re-setting system<br />
and<br />
Obsolete<br />
Helpdesk are stored in the mailing<br />
Product<br />
machine.<br />
9. Registration<br />
Enables Change Address, Audit and Withdrawal<br />
transactions.<br />
10. Language<br />
Details Language setting (Factory set to American English).<br />
11. Report On<br />
Enables the supervisor to determine report printing mode e.g.<br />
internal label printer, remote printer or PC (Factory set to<br />
internal label printer).<br />
12. Firmware Update <strong>Hasler</strong> Service Only.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 13
HASLER Supervisor Settings Section 8<br />
Machine Setup<br />
From the SUPERVISOR menu, move the cursor to the<br />
SETUP option.<br />
Press to confirm.<br />
The following screen will now be observed:<br />
High Value<br />
From the SETUP screen select HIGH VALUE and press<br />
Obsolete Product<br />
to confirm, the following screen will be observed:<br />
To return to the SETUP menu with the original value<br />
unchanged, press .<br />
To change the High Value, enter the new value (with no point<br />
or comma, e.g. 100 corresponds to $1.00), then press<br />
to confirm.<br />
To return to the Supervisor Ready screen press<br />
twice.<br />
Page 8 - 14 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
Low Credit<br />
From the SETUP screen select LOW CREDIT and press<br />
to confirm, the following screen will be observed:<br />
LOW CREDIT<br />
$0.00<br />
To return to the previous screen with the original value<br />
unchanged, press .<br />
To change the Low Credit Threshold, enter the new<br />
value (with no point or comma, e.g. 5000<br />
Obsolete Product<br />
corresponds to $50.00), then press<br />
confirm.<br />
To return to the Supervisor Ready screen press<br />
twice.<br />
to<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 15
HASLER Supervisor Settings Section 8<br />
Time<br />
From the SETUP screen select TIME and press<br />
confirm, the following screen will be observed:<br />
to<br />
TIME<br />
_ _ : _ _<br />
To return to the previous screen with the Time Setting<br />
unchanged, press .<br />
Obsolete Product<br />
To change the Time Setting, enter the new value, (with no<br />
point or comma, e.g.:1345 corresponds to 1:45 pm,<br />
maximum variance + 3hours), then press<br />
confirm.<br />
To return to the Supervisor Ready screen press<br />
twice.<br />
to<br />
Page 8 - 16 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
Sleep Mode<br />
From the SETUP screen select Sleep Mode and press<br />
to confirm, the following screen will be observed:<br />
STANDBY TIMEOUT<br />
0<br />
To return to the previous screen with the original value<br />
unchanged, press .<br />
To change the Sleep Mode time period, enter the new value<br />
(with<br />
Obsolete<br />
no point or comma, e.g. 5 corresponds<br />
Product<br />
to 5 minutes),<br />
then press to confirm.<br />
To return to the Supervisor Ready screen press<br />
twice.<br />
Key Beep<br />
From the SETUP screen select KEY BEEP and press<br />
to confirm, the following screen will be observed:<br />
1 ON<br />
2 OFF<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 17
HASLER Supervisor Settings Section 8<br />
To return to the previous screen with the Setting unchanged,<br />
press .<br />
Use the and keys to change the setting, then<br />
press<br />
to confirm.<br />
To return to the Supervisor Ready screen press<br />
twice.<br />
Default Stamp Value<br />
From the SETUP screen select DEFAULT STAMP VALUE<br />
and press<br />
observed:<br />
to confirm, the following screen will be<br />
DEFAULT STAMP VALUE<br />
$0.00<br />
Obsolete Product<br />
To return to the SETUP menu with the original value<br />
unchanged, press .<br />
To change the DEFAULT STAMP VALUE, enter the new value<br />
(with no point or comma, e.g. 1000 corresponds to $1.000),<br />
then press<br />
to confirm.<br />
To return to the Supervisor Ready screen press<br />
twice.<br />
Page 8 - 18 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
Registration<br />
From the SETUP screen select REGISTRATION and press to confirm,<br />
the following screen will be observed:<br />
1 CHANGE ADDRESS<br />
2 AUDIT<br />
3 WITHDRAW<br />
Change Address<br />
If you have changed your address, call the <strong>Hasler</strong> Helpdesk at<br />
1-800-446-6027. A customer service representative will take<br />
your information and guide you through the update procedure.<br />
Obsolete Product<br />
Audit<br />
USPS regulations require that your meter must be set at least<br />
once every three months and the meter has an internal timer<br />
that tracks your reset activity. If you wish to avoid a PO<br />
LOCKOUT, you can perform an AUDIT transaction any time<br />
prior to the timer expiration. When the Audit transaction is<br />
completed, postage printing is enabled for another 3 months.<br />
Withdraw<br />
The Withdraw procedure is only required if you are canceling<br />
your meter contract or if there is a technical problem with your<br />
meter. Call the <strong>Hasler</strong> Helpdesk at 1-800-243-6275 and a<br />
customer service representative will take your information and<br />
guide you through the withdraw procedure. Your meter<br />
should always be withdrawn before returning it to <strong>Hasler</strong>.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 19
HASLER Supervisor Settings Section 8<br />
Telephone Settings<br />
The telephone number of the <strong>Hasler</strong> TMS® re-setting center<br />
is stored in the mailing machine. This is used when you want<br />
to purchase postage.<br />
Modification of the telephone number is permitted only by the<br />
supervisor. Such a setting may be necessary in case of<br />
modification of your telephone network (for example a new<br />
prefix for an external line), or if you are advised that the <strong>Hasler</strong><br />
TMS® number has changed.<br />
Telephone Number Change<br />
From the SETUP screen select TELEPHONE SETTINGS<br />
and press<br />
observed:<br />
to confirm, the following screen will be<br />
Obsolete Product<br />
If you are advised of a telephone number change, move the<br />
cursor to the number to be changed (e.g. 1 POSTAGE<br />
REFILL NUMBER) and press<br />
following screen will now be observed:<br />
to confirm, the<br />
Continued on the next page.<br />
Page 8 - 20 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
To return to the SETUP menu with the telephone number<br />
unchanged, press .<br />
Or enter the new number using the numeric keypad, then<br />
press<br />
to confirm.<br />
Changes to Prefix, Pause, Tone Delay and Dial Delay<br />
Settings<br />
PREFIX If your outside line is routed through a switchboard,<br />
telephone numbers must be prefixed by the appropriate<br />
outside line digit (for most systems this is a 9 or a 0).<br />
PAUSE With some telephone networks it may be necessary<br />
to enter a pause between the outside line digit and the<br />
telephone number.<br />
TONE DETECT Waits for a dial tone to be detected before<br />
dialing out.<br />
DIAL DELAY You may wish to enter delay a between dialing<br />
attempts.<br />
Obsolete Product<br />
Using the and keys, or the appropriate<br />
number key, move the cursor to make a selection and press<br />
to confirm, the following typical screen will be<br />
observed:<br />
Using the numerical keypad enter your prefix and press<br />
PREFIX<br />
NONE<br />
to confirm.<br />
Or, to return to the TELEPHONE SETTINGS screen with the<br />
prefix unchanged press .<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 21
HASLER Supervisor Settings Section 8<br />
Memory Cards<br />
The following memory cards are currently available from<br />
<strong>Hasler</strong>:<br />
Slogan Cards (one message per card)<br />
Rate Card (when postal rates change)<br />
How To Load Data Using a Memory Card<br />
The following example illustrates the loading of a<br />
slogan/message, (remember only 2 slogans/messages can<br />
be stored in the machine at any one time in addition to the 7<br />
preloaded slogans).<br />
From the SUPERVISOR screen select LOAD FROM<br />
MEMORY CARD and press<br />
following screen will be observed:<br />
to confirm, the<br />
Obsolete<br />
INSERT<br />
Product<br />
CARD<br />
Insert the memory card<br />
face uppermost into the<br />
card reader, on the right<br />
hand side of the<br />
machine as illustrated:<br />
Continued on the next<br />
page.<br />
Page 8 - 22 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
Press<br />
to confirm.<br />
The prompt to load the Memory Card Message/Slogan will<br />
now be observed:<br />
1 SLOGAN 1<br />
To return to the previous screen press .<br />
Obsolete Product<br />
Press<br />
to initiate the downloading operation.<br />
On completion of the downloading process the following<br />
screen will be observed:<br />
LOADING FROM MEMORY CARD<br />
LOADING COMPLETE<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 23
HASLER Supervisor Settings Section 8<br />
How To Replace Data Using a Memory Card<br />
From the SUPERVISOR screen select LOAD FROM<br />
MEMORY CARD and press<br />
following screen will be observed:<br />
to confirm, the<br />
INSERT CARD<br />
Insert the memory card<br />
face uppermost into the<br />
card reader, on the right<br />
hand side of the<br />
machine as illustrated:<br />
Obsolete Product<br />
Press<br />
confirm.<br />
to<br />
The prompt to load the<br />
Memory Card<br />
Message/Slogan will now be observed:<br />
1 SLOGAN 1<br />
To return to the previous screen press .<br />
Continued on the next page.<br />
Page 8 - 24 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
Press to confirm.<br />
The following display will now be observed:<br />
1 SLOGAN 1<br />
2 SLOGAN 2<br />
If you do not wish to replace a file, press<br />
return to the Supervisor Ready screen.<br />
twice to<br />
If you wish to replace a file, use the and keys,<br />
or the appropriate number key to move the cursor to the<br />
message/slogan to be replaced.<br />
Obsolete Product<br />
Now press to initiate the downloading operation.<br />
On completion of the downloading process the following<br />
screen will be observed:<br />
LOADING FROM MEMORY CARD<br />
LOADING COMPLETE<br />
To return to the Supervisor Ready screen press<br />
twice.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 25
HASLER Supervisor Settings Section 8<br />
Text Messages<br />
Starting from the SUPERVISOR menu, move the cursor to<br />
the TEXT option.<br />
Press<br />
observed:<br />
to confirm. The following screen will now be<br />
Using the and keys, or the appropriate<br />
number key, move the cursor to the message you wish to set<br />
and press<br />
observed:<br />
to confirm, the TEXT screen will be<br />
Obsolete Product<br />
_<br />
TEXT<br />
A B C D E F G H I J K L M N O P Q R S T<br />
U V W X Y Z # - ! % : $ ‘ . ?<br />
Use the , and keys to move the<br />
cursor to the character to be defined.<br />
The key is used to confirm the selection and move<br />
the cursor to the next character.<br />
To delete a character press .<br />
Continued on the next page.<br />
Page 8 - 26 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
To enter numbers in the text use the numeric keypad, you do<br />
not need to press the<br />
when entering numbers.<br />
key to confirm selection<br />
A text is limited to two lines of 16 characters including<br />
spaces.<br />
To return to the previous screen with the text message<br />
unchanged press<br />
previous one.<br />
until the screen changes to the<br />
To confirm your entry press .<br />
To Change a Text Message, select TEXT as described<br />
above.<br />
Obsolete Product<br />
Using the key, delete characters of the old text<br />
message. Press as many times as required to erase<br />
the message completely, then enter the new message as<br />
previously detailed.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 27
HASLER Supervisor Settings Section 8<br />
Reports<br />
Supervisor Reports can be printed using the mailing<br />
machine's self-adhesive label printer or by connection to an<br />
approved external printer. Your <strong>WJ60</strong>/<strong>WJ90</strong> has been factory<br />
set for internal (LABEL) printing, to select external (PRINTER)<br />
printing, see below.<br />
Typical Report<br />
DEPARTMENT REGISTERS<br />
DEP NAME TOTAL ITEMS<br />
MARKETING $235.67 759<br />
R & D $27.12 69<br />
ACCOUNTS $8.52 18<br />
SALES $107.52 512<br />
Printing a Report<br />
Starting from the SUPERVISOR menu, move the cursor to<br />
the REGISTERS option.<br />
Obsolete Product<br />
Press to confirm.<br />
The following screen will now be observed:<br />
Using the and keys, or the appropriate<br />
number key, select a register option from the list and press<br />
to confirm.<br />
Continued on the next page.<br />
Page 8 - 28 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
Example: 3 DEPARTMENT REGISTERS<br />
To print a register press , if the method of print is<br />
set to LABELS (Internal), the prompt to FEED LABEL will be<br />
observed:<br />
Obsolete Product<br />
Press .<br />
When report printing is initiated, the screen will display a label<br />
icon with a block/label number alongside. This number<br />
decrements as report printing progresses, (nine department<br />
label blocks for IJ35, twelve for IJ45), plus one label containing<br />
the user report).<br />
On completion of printing, the DEPARTMENT<br />
REGISTERS screen will be observed.<br />
If the method of print is set to EXTERNAL PRINTER, please<br />
refer Printing with External Printer.<br />
Continued on the next page.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 29
HASLER Supervisor Settings Section 8<br />
To change the method of print please refer to Setting the<br />
Print Destination.<br />
Press<br />
to return to the REGISTERS screen.<br />
To return to SUPERVISOR screen press<br />
twice.<br />
Setting the Report Destination<br />
From the SETUP screen select REPORT ON and press<br />
to confirm, the following screen will be observed:<br />
Obsolete Product<br />
Using the and keys, or the appropriate<br />
number key, move the cursor to make a selection and press<br />
to confirm.<br />
Or, to return to the SETUP screen with the print destination<br />
unchanged press .<br />
Page 8 - 30 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Supervisor Settings Section 8<br />
Printing with External Printer<br />
Before proceeding to print registers using an external<br />
printer ensure that the printer lead is connected to<br />
the Upper Accessory Port at the back of the machine,<br />
(please refer to Controls and Features in Section 2)<br />
and that the printer power lead is connected to an<br />
adjacent power outlet.<br />
Set the printer to ON and the status to ONLINE.<br />
From your selected registers screen, press<br />
, the WAIT screen will now be observed:<br />
Obsolete Product<br />
After a short period of time, the screen will return to<br />
DEPARTMENT REGISTERS and the registers will<br />
have been printed.<br />
There Is No External Printer Feedback To Your Mailing<br />
Machine, therefore If the DEPARTMENT REGISTERS<br />
screen does not re-appear after a few seconds and<br />
the printer does not print, re-check all printer<br />
connections and ensure that the printer status is set to<br />
ONLINE.<br />
The external printer must be a serial printer and set<br />
as follows: Baud Rate - 9600, Data Bits - 8, Stop Bits<br />
- 1, Parity - None.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page 8 - 31
This page intentionally left blank.<br />
Obsolete Product
HASLER Q&A Appendix A<br />
Contacting <strong>Hasler</strong><br />
<strong>Hasler</strong> , <strong>Inc</strong>.<br />
19 Forest Parkway<br />
Shelton, CT 06484-6140<br />
www.haslerinc.com<br />
Customer Service Helpdesk 1-800-446-6027<br />
Call for Product Questions and Support<br />
TMS Automated Account Information 1-800-248-8013<br />
Call to check Account Balance, Last Deposit or Last Meter<br />
Resetting via touch-tone telephone<br />
TMS Modem Telephone Number 1-800-446-6029<br />
Modem telephone number set up in meter<br />
Obsolete Product<br />
Contact Information A-1<br />
How To Perform Common Functions A-2<br />
Troubleshooting Tips A-3<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page A - 1
HASLER Q&A Appendix A<br />
How To<br />
Department/User , to choice,<br />
Enter PIN (example<br />
1 5 9 5)<br />
Set value (example<br />
95 cents)<br />
Confirm High Value<br />
(example:$15.00)<br />
Set Print Mode<br />
Select Slogan<br />
, , ,<br />
, , ,<br />
, , , , ,<br />
, Are you sure,<br />
, to choice,<br />
, Slogan, , to<br />
choice, ,<br />
Select Text<br />
, Text Message, ,<br />
Message<br />
Obsolete<br />
to choice,<br />
Product<br />
,<br />
Advance Date<br />
, Date Advance, ,<br />
Advance Date, ,<br />
Print Label<br />
Recall memorized<br />
jobs<br />
Recredit (example<br />
$100.00)<br />
Display Registers<br />
To print Registers<br />
, , , , ,<br />
Label quantity,<br />
, Memory Recall, ,<br />
Memory 1 or 2, ,<br />
, , , , ,<br />
,<br />
, Registers, ,<br />
to choice,<br />
As Registers, , ,<br />
Page A - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Q&A Appendix A<br />
Troubleshooting<br />
<strong>WJ60</strong>/<strong>WJ90</strong> will not<br />
start.<br />
• Is the <strong>WJ60</strong>/<strong>WJ90</strong> connected to the<br />
power supply?<br />
• Is the main power outlet switch set<br />
to ON?<br />
• Is the machine Top Cover properly<br />
closed?<br />
• Check plug fuse (5A).<br />
• Check machine fuse (1.6A).<br />
The printer does not<br />
operate.<br />
The Autofeed does<br />
not operate.<br />
The unit does not<br />
print.<br />
• Is the printer switched to ON?<br />
• Is the printer connected to the power<br />
supply?<br />
• Is the main power outlet switch set<br />
to ON?<br />
• Check plug fuse.<br />
• Have you selected the correct print<br />
mode?<br />
Obsolete Product<br />
Check the connection to the<br />
<strong>WJ60</strong>/<strong>WJ90</strong>.<br />
• Check that you have made the<br />
correct Print Mode Selection<br />
• Did you remove the protective tape<br />
from the Ink Cartridge before fitting?<br />
Poor print quality<br />
Envelopes not fed<br />
properly or fed<br />
double:<br />
Labels do not feed<br />
properly.<br />
The scale does not<br />
communicate<br />
• Clean the inker<br />
Autofeed incorrectly loaded.<br />
• Avoid leaving the labels in the<br />
machine for too long.<br />
• Avoid overloading the dispenser (50<br />
max).<br />
• Check the scale connection.<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page A - 3
This page intentionally left blank.<br />
Obsolete Product
HASLER<br />
Country Code Appendix B<br />
Country<br />
Rate Group<br />
A<br />
Afghanistan 5<br />
Albania 5<br />
Algeria 5<br />
Andorra 3<br />
Angola 5<br />
Anguilla 5<br />
Antigua & Barbuda 5<br />
Argentina 5<br />
Armenia 5<br />
Aruba 5<br />
Ascension 5<br />
Australia 4<br />
Austria 5<br />
Azerbaijan 5<br />
Country<br />
Rate Group<br />
Chad 5<br />
Chile 5<br />
China 5<br />
Colombia 5<br />
Comoros 5<br />
Congo, Democratic Republic of the<br />
5<br />
Congo, Republic of the 5<br />
Costa Rica 5<br />
Cote d’Ivoire (Ivory Coast) 5<br />
Croatia 5<br />
Cuba 5<br />
Cyprus 5<br />
Czech Republic 5<br />
B<br />
Bahamas 5<br />
D<br />
Denmark 3<br />
Bahrain 5<br />
Djibouti 5<br />
Bangladesh 5<br />
Dominica 5<br />
Barbados<br />
Obsolete<br />
5<br />
Product<br />
Dominican Republic 5<br />
Belarus 5<br />
Belgium 3<br />
E<br />
Belize 5<br />
Ecuador 5<br />
Benin 5<br />
Egypt 5<br />
Bermuda 5<br />
El Salvador 5<br />
Bhutan 5<br />
Equatorial Guinea 5<br />
Bolivia 5<br />
Eritrea 5<br />
Bosnia-Herzegovina 5<br />
Estonia 5<br />
Botswana 5<br />
Ethiopia 5<br />
Brazil 5<br />
British Virgin Islands 5<br />
Brunei Darussalam 5<br />
Bulgaria 5<br />
Burkina Faso 5<br />
Burma (Myanmar) 5<br />
Burundi 5<br />
C<br />
Cambodia 5<br />
Cameroon 5<br />
Canada 1<br />
Cape Verde 5<br />
Cayman Islands 5<br />
F<br />
Falkland Islands 5<br />
Faroe Islands 3<br />
Fiji 5<br />
Finland 3<br />
France 3<br />
French Guiana 5<br />
French Polynesia 5<br />
G<br />
Gabon 5<br />
Gambia 5<br />
Georgia, Republic of 5<br />
Germany 3<br />
Ghana 5<br />
Gibraltar 3<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page B - 1
HASLER Country Code Appendix B<br />
Country<br />
Rate<br />
Group<br />
Great Britain & Northern Ireland 3<br />
Greece 3<br />
Greenland 3<br />
Grenada 5<br />
Guadeloupe 5<br />
Guatemala 5<br />
Guinea 5<br />
Guinea-Bissau 1 5<br />
Guyana 5<br />
H<br />
Haiti 5<br />
Honduras 5<br />
Hong Kong 5<br />
Hungary 5<br />
Country<br />
Rate Group<br />
Libya 5<br />
Liechtenstein 3<br />
Lithuania 5<br />
Luxembourg 3<br />
M<br />
Macao 5<br />
Macedonia, Republic of 5<br />
Madagascar 5<br />
Malawi 5<br />
Malaysia 5<br />
Maldives 5<br />
Mali 5<br />
Malta 5<br />
Martinique 5<br />
Mauritania 5<br />
Mauritius 5<br />
I<br />
Iceland 3<br />
Mexico 2<br />
India 5<br />
Moldova 5<br />
Indonesia 5<br />
Mongolia 5<br />
Iran<br />
Obsolete<br />
5<br />
Montserrat<br />
Product<br />
5<br />
Iraq 5<br />
Morocco 5<br />
Ireland (Eire) 3<br />
Mozambique 5<br />
Israel 3<br />
Italy 3<br />
N<br />
J<br />
Jamaica 5<br />
Japan 4<br />
Jordan 5<br />
K<br />
Kazakhstan 5<br />
Kenya 5<br />
Kiribati 5<br />
Korea, Democratic People’s Republic<br />
of (North) 5<br />
Korea, Repub. of (South) 5<br />
Kuwait 5<br />
Kyrgyzstan 5<br />
L<br />
Laos 5<br />
Latvia 5<br />
Namibia 5<br />
Nauru 5<br />
Nepal 5<br />
Netherlands 3<br />
Netherlands Antilles 5<br />
New Caledonia 5<br />
New Zealand 4<br />
Nicaragua 5<br />
Niger 5<br />
Nigeria 5<br />
Norway 3<br />
O<br />
Oman 5<br />
P<br />
Pakistan 5<br />
Panama 5<br />
Page B - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
HASLER Country Codes Section B<br />
Country<br />
Rate<br />
Group<br />
Poland 5<br />
Portugal 3<br />
Q<br />
Qatar 5<br />
R<br />
Reunion 5<br />
Romania 5<br />
Russia 5<br />
Rwanda 5<br />
Country<br />
Rate<br />
Group<br />
Tanzania 5<br />
Thailand 5<br />
Togo 5<br />
Tonga 5<br />
Trinidad & Tobago 5<br />
Tristan da Cunha 5<br />
Tunisia 5<br />
Turkey 5<br />
Turkmenistan 5<br />
Turks & Caicos Islands 5<br />
Tuvalu 5<br />
S<br />
St. Christopher (St. Kitts) & Nevis 5<br />
Saint Helena<br />
5<br />
U<br />
Uganda<br />
Ukraine<br />
United Arab Emirates<br />
5<br />
5<br />
5<br />
Saint Lucia 5<br />
Uruguay 5<br />
Saint Pierre & Miquelon 5<br />
Uzbekistan 5<br />
Saint Vincent & Grenadines 5<br />
San Marino 3<br />
V<br />
Sao<br />
Obsolete<br />
Tome & Principe 5<br />
Product<br />
Vanuatu 5<br />
Saudi Arabia 5<br />
Vatican City 3<br />
Senegal 5<br />
Venezuela 5<br />
Serbia-Montenegro (Yugoslavia) 5<br />
Vietnam 5<br />
Seychelles<br />
5<br />
W<br />
Sierra Leone 5<br />
Wallis & Futuna Islands 5<br />
Singapore 5<br />
Western Samoa 5<br />
Slovak Republic (Slovakia) 5<br />
Slovenia 5<br />
Y<br />
Solomon Islands 5<br />
Yemen 5<br />
Somalia 11 5<br />
South Africa 5<br />
Z<br />
Spain 3<br />
Zambia 5<br />
Sri Lanka 5<br />
Zimbabwe 5<br />
Sudan 5<br />
Suriname 5<br />
Swaziland 5<br />
Sweden 3<br />
Switzerland 3<br />
Syrian Arab Republic (Syria) 5<br />
T<br />
Taiwan 5<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Page B - 3
This page intentionally left blank.<br />
Obsolete Product
<strong>Hasler</strong><br />
Index<br />
A<br />
Accounts<br />
… See Departments<br />
Add Dies<br />
… See Slogans<br />
Autofeed:<br />
Connection 1-7<br />
Printing Postage With 3-11<br />
Moistener with 4-2<br />
B<br />
Adding Postage:<br />
Adding Postage 6-2<br />
Clearing A PO Lockout 6-4<br />
Contact Information 6-13<br />
Maintaining Your TMS Account<br />
Number 6-5<br />
Mailing Your TMS Deposit 6-12<br />
Managing Your Account 6-10<br />
Modem Connection 6-2<br />
Postage Now 6-7<br />
Postage Now On Demand 6-9<br />
Postage Now Telefunds 6-8<br />
Post Office Regulations 6-6<br />
Standard TMS Bank Accounts<br />
6-11<br />
TMS Account Balance 6-5<br />
TMS Account Number 6-5<br />
TMS Account Statements 6-6<br />
WARNING PENDING CREDIT<br />
Procedure 6-3<br />
C<br />
Calculating Postage 3-19<br />
Cautions FCC-1<br />
Change Address 8-19<br />
Changing The User PIN 8-5<br />
Choosing A Slogan, Rate Die,<br />
or Text 3-25<br />
Obsolete Product<br />
Connecting:<br />
Autofeed 1-7<br />
Power Cord 1-9<br />
Telephone Line 1-8<br />
Weigh Platform 1-6<br />
Administrator Settings<br />
… See Supervisor Settings<br />
Assign A Department 8-7<br />
Attaching the Moistener Unit<br />
Platform 1-2,3<br />
Attaching the Weigh Platform<br />
1-4<br />
Audit 8-19<br />
Contact Information A-1<br />
Controls & Features:<br />
Control Descriptions 2-2<br />
Control Locations 2-3<br />
Display 2-5<br />
Function Keys 2-4<br />
Sample Indicia 2-5<br />
Country Codes B-1<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Index - 1
<strong>Hasler</strong><br />
Index<br />
D<br />
Date Advance 3-26<br />
Default Stamp Value 8-18<br />
Departments:<br />
Assign A Department 8-7<br />
Change A Department 3-10<br />
Change A Department Name 8-9<br />
Change The Department Status<br />
8-11<br />
Department Code 8-10<br />
Departmental Control 8-4<br />
Departmental Info 3-4<br />
Reset The Department Registers<br />
8-11<br />
Display 2-5<br />
Fitting the Moistener Unit<br />
Wick 1-2<br />
Function Keys 2-4<br />
G<br />
H<br />
High Value:<br />
High Value Selection 3-8<br />
High Value Setup 8-14<br />
How To Perform Common<br />
Functions A-3<br />
I<br />
E<br />
Obsolete Product<br />
Indicia, Sample 2-5<br />
Entry To Supervisor Mode<br />
8-2 Ink:<br />
Low Ink 3-31<br />
Envelope Moistener<br />
… See Moistener<br />
No Ink 3-31<br />
External Printer:<br />
Printing Report With 8-31<br />
Printing Registers With 5-5<br />
F<br />
FCC Compliance Statement<br />
FCC-1<br />
Ink Cartridge:<br />
Cleaning 3-28<br />
Replacing 3-32<br />
Installation Section 1<br />
Installation Tips 1-1<br />
Installation Safety FCC-2<br />
Insufficient Credit 3-8<br />
Filling the Label Dispenser<br />
1-5<br />
Filling the Moistener Reservoir<br />
1-11<br />
J<br />
Jam, Clear 3-13<br />
Index - 2 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
<strong>Hasler</strong><br />
Index<br />
K<br />
Key Beep 8-17<br />
L<br />
Label Dispenser Filling 1-5<br />
Loading Funds<br />
… See Adding Postage<br />
Log Off 3-10<br />
Log On (PIN Entry) 3-3<br />
Modem Approval<br />
Requirements FCC-2<br />
Modem Connection 6-2<br />
Modifying The Imprint 3-24<br />
Moistener:<br />
Filling The Reservoir 4-2<br />
Reservoir Filling 1-11<br />
Unit Platform Attachment 1-2,3<br />
Unit Wick 1-2<br />
Using With Plain Platform 4-1<br />
Using With Autofeed 4-2<br />
Low Credit:<br />
Low Credit 3-8<br />
Low Credit Setup 8-15<br />
M<br />
Machine Setup<br />
… See Supervisor Settings<br />
Macros<br />
… See Memory Function<br />
Memory Card<br />
… See Rate Card<br />
Moistener Reservoir Filling<br />
1-11<br />
Moistener Unit Platform<br />
Attachment 1-2,3<br />
Low Ink 3-31<br />
Obsolete Product<br />
Moistener Unit Wick 1-2<br />
N<br />
No Ink 3-31<br />
O<br />
Memory Functions:<br />
Recalling A Memory Function 7-3<br />
Saving A Memory Function 7-1<br />
Meter Registers:<br />
Meter Register Selection 5-2<br />
Printing A Register 5-4<br />
Printing Registers With External<br />
Printer 5-5<br />
Sample Register Displays 5-1<br />
P<br />
Phone Line Connection<br />
1-8<br />
PIN<br />
Changing The User Pin 8-5<br />
PIN Entry 3-3<br />
PO Lockout, Clearing 6-4<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Index - 3
<strong>Hasler</strong><br />
Index<br />
Postage Now<br />
… See Adding Postage<br />
Printing Registers With<br />
External Printer 5-5<br />
Positioning the Receiving Tray<br />
1-10<br />
Print Quality<br />
Proprietary Notice<br />
3-28<br />
Pub-1<br />
Power Cord Connection 1-9<br />
Publication Notice Pub-1<br />
Printing:<br />
Calculating Postage 3-19<br />
Change A Department 3-10<br />
Choosing A Slogan, Rate Die, or<br />
Q<br />
Text 3-25<br />
Cleaning Ink Cartridge 3-28<br />
Clear A Jam 3-13<br />
R<br />
Date Advance 3-26<br />
Rate Card<br />
Departmental Info 3-4<br />
Choosing A Rate Die 3-25<br />
High Value Selection 3-8<br />
Memory (Slogan/Rate) Cards 8-22<br />
Insufficient Credit 3-8<br />
Replace Data 8-24<br />
Log Off 3-10<br />
Log<br />
Obsolete<br />
On (PIN Entry) 3-3<br />
Low Credit 3-8 Receiving<br />
Product<br />
Tray Positioning<br />
Low Ink 3-31<br />
1-10<br />
Maintaining Print Quality 3-28<br />
Making A Test Print 3-29 Registers<br />
Modifying The Imprint 3-24<br />
… See Meter Registers<br />
No Ink 3-31<br />
Printing Tips<br />
Print Mode Selection<br />
3-2<br />
3-23<br />
Print Modes<br />
Print Postage Autofeed<br />
3-22<br />
3-11<br />
Registration<br />
Replacing Ink Cartridge<br />
8-19<br />
3-31<br />
Printing Reports 8-28<br />
Printing With External Printer 8-31 Reports:<br />
Printing With Labels 3-15<br />
Printing A Report 8-28<br />
Printing w/Weigh Platform 3-18<br />
Reports 8-28<br />
Replacing Ink Cartridge 3-31<br />
Setting Report Destination 8-30<br />
Select A Postage Value 3-6<br />
Stamping An Envelope 3-9<br />
Predating Mail 3-25<br />
Print Modes 3-22<br />
Print Mode Selection 3-23<br />
S<br />
Safety, Installation<br />
FCC-2<br />
Select A Postage Value 3-6<br />
Sleep Mode 8-17<br />
Index - 4 <strong>WJ60</strong>/<strong>WJ90</strong> 06/2003
<strong>Hasler</strong><br />
Index<br />
Slogans:<br />
Choosing A Slogan 3-25<br />
Memory (Slogan/Rate) Cards 8-22<br />
Stamping An Envelope 3-9<br />
Supervisor Code 9430<br />
Test Print 3-29<br />
Text Messages:<br />
Choosing A Text Message 3-25<br />
Text Messages Setup 8-26<br />
Time 8-16<br />
Supervisor Settings:<br />
Assign A Department 8-7<br />
Change A Department Name 8-9<br />
Change The Department Status<br />
8-11<br />
Changing The User PIN 8-5<br />
Default Stamp Value 8-18<br />
Department Code 8-10<br />
Departmental Control 8-4<br />
Entry To Supervisor Mode 8-2<br />
High Value 8-14<br />
Key Beep 8-17<br />
Low Credit 8-15<br />
Machine Setup Menu 8-12<br />
Machine Setup 8-14<br />
Memory (Rate/Slogan) Cards 8-22<br />
Printing A Report 8-28<br />
Printing With External Printer 8-31<br />
Replace Data 8-24<br />
Registration 8-19<br />
Reports 8-28<br />
Reset The Department Registers<br />
8-11<br />
Setting Report Destination 8-30<br />
Setting The User Status 8-6<br />
Sleep Mode 8-17<br />
Telephone Settings 8-20<br />
Text Messages 8-26<br />
Time 8-16<br />
T<br />
Tape Dispenser Filling 1-5<br />
TMS:<br />
Adding Postage Section 6<br />
Maintaining Account Number 6-5<br />
Postage Now 6-7<br />
Post Office Regulations 6-6<br />
Standard TMS Accounts 6-11<br />
TMS Account Balance 6-5<br />
TMS Account Number 6-5<br />
TMS Bank Account Deposits 6-12<br />
TMS Statements 6-6<br />
Troubleshooting Tips A-3<br />
Obsolete Product<br />
U<br />
User Pin<br />
… See PIN<br />
V<br />
W<br />
WARNING PENDING CREDIT<br />
Procedure 6-3<br />
Weigh Platform Attachment<br />
1-4<br />
Weigh Platform Connection<br />
1-6<br />
Withdraw 8-19<br />
Telephone:<br />
Telephone Line Connection 1-8<br />
Telephone Settings 8-20<br />
X, Y, Z<br />
06/2003 <strong>WJ60</strong>/<strong>WJ90</strong> Index - 5
Obsolete Product<br />
Form 50813 06/2003