Room units and controllers - Domat International
Room units and controllers - Domat International Room units and controllers - Domat International
MODBUS UI01x User interface V3 Address bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 Function Range 77 LSB 10xsecs secs sec 00-59 77 MSB 0 10xmins mins min 00-59 78 LSB 0 10xhour 10xhour hours hour 00-23 78 MSB 0 0 0 0 0 weekday dow 01-07 79 LSB 0 0 10xday day day 01-31 79 MSB 0 0 0 10xmonth month month 01-12 80 LSB 10xyear year year 00-99 80 MSB 0 0 0 0 0 0 0 0 N/A 00 22
MODBUS UC100 Room controller V3 UC100 – room controller, knob + RTC 23 - 60 words can be read at the same time (i.e. 120 bytes) - whole range can be addressed bitwise name address type description notes / defaults module ID 1 LSB R module type identification 0300hex 1 MSB firmware 2 LSB 2 MSB R firmware version old LCD displays: less than 100 new LCD displays: 100 and above (PCB status LSB 3 LSB R, W RAM module status lower byte bit 0 – write to EEPROM enabled bit 4 – init EEPROM status MSB 3 MSB R, RAM module status upper byte bit 0 0: normal mode 1: init mode bit 1 address 4 LSB R,W EEPROM baud rate 4 MSB R,W EEPROM serial port settings 5 LSB R,W EEPROM 1: at the next EEPROM write attempt will all data be written to EEPROM 0: at the next EEPROM write attempt will all data be written to RAM only bit 2 – 1 – EEPROM initialized bit 3 – N/A bit 4 – 0 bit 5 – 1 bit 6 – 0 bit 7 – commissioning mode (1...active) Modbus module address (default = 1) 5 MSB reserved communication speed 10dec … 1 200 bps 11dec … 2 400 bps 12dec … 4 800 bps 13dec … 9 600 bps (default) 14dec … 19 200 bps 15dec … 38 400 bps 16dec … 57 600 bps 17dec … 115 200 bps serial line parameter settings (default = no parity, 1 stop bit) V1.6 and above) Init EEPROM follows if the INIT switch was ON at power up, and if INIT switch was OFF at setting bit 4 to 1 (indicated by bit 2 in Status MSB) !!! the change will be effective after restart only (however the register will be set immediately) !!! the change will be effective after restart only (however the register will be set immediately) bit 0-1 ... parity (00 – no parity, 01 – even, 10 – odd) bit 2 ... stop bits (0 – one, 1 - two) !!! the change will be effective after restart only (however the register will be set immediately)
- Page 1 and 2: Room units and controllers Communic
- Page 3 and 4: MODBUS General V3 General • All r
- Page 5 and 6: MODBUS UI01x User interface V3 stat
- Page 7 and 8: MODBUS UI01x User interface V3 set
- Page 9 and 10: MODBUS UI01x User interface V3 sett
- Page 11 and 12: MODBUS UI01x User interface V3 max
- Page 13 and 14: MODBUS UI01x User interface V3 dec
- Page 15 and 16: MODBUS UI01x User interface V3 allo
- Page 17 and 18: MODBUS UI01x User interface V3 disp
- Page 19 and 20: MODBUS UI01x User interface V3 prog
- Page 21: MODBUS UI01x User interface V3 actu
- Page 25 and 26: MODBUS UC100 Room controller V3 set
- Page 27 and 28: MODBUS UC100 Room controller V3 P b
- Page 29 and 30: MODBUS UC100 Room controller V3 pre
- Page 31 and 32: MODBUS UC100 Room controller V3 Rea
- Page 33 and 34: MODBUS UC200 Room controller V3 5 M
- Page 35 and 36: MODBUS UC200 Room controller V3 act
- Page 37 and 38: MODBUS UC200 Room controller V3 max
- Page 39 and 40: MODBUS UC200 Room controller V3 pro
- Page 41 and 42: MODBUS UC300 Room floor heating con
- Page 43 and 44: MODBUS UC300 Room floor heating con
- Page 45 and 46: MODBUS UC300 Room floor heating con
- Page 47 and 48: MODBUS UC300 Room floor heating con
- Page 49 and 50: MODBUS UC300 Room floor heating con
- Page 51 and 52: MODBUS FC010 Fancoil controller V3
- Page 53 and 54: MODBUS FC010 Fancoil controller V3
- Page 55 and 56: MODBUS FC010 Fancoil controller V3
- Page 57 and 58: MODBUS FC010 Fancoil controller V3
- Page 59 and 60: MODBUS FC010 Fancoil controller V3
- Page 61 and 62: MODBUS FC020 Fancoil controller V2
- Page 63 and 64: MODBUS FC020 Fancoil controller V2
- Page 65 and 66: MODBUS FC020 Fancoil controller V2
- Page 67 and 68: MODBUS FC020 Fancoil controller V2
- Page 69 and 70: MODBUS FC020 Fancoil controller V2
- Page 71 and 72: MODBUS UC210 Dynamic radiator contr
MODBUS UI01x User interface V3<br />
Address bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 Function Range<br />
77 LSB 10xsecs<br />
secs<br />
sec 00-59<br />
77 MSB 0 10xmins<br />
mins<br />
min 00-59<br />
78 LSB 0<br />
10xhour<br />
10xhour<br />
hours<br />
hour 00-23<br />
78 MSB 0 0 0 0 0 weekday<br />
dow 01-07<br />
79 LSB 0 0 10xday<br />
day<br />
day 01-31<br />
79 MSB 0 0 0 10xmonth month<br />
month 01-12<br />
80 LSB 10xyear<br />
year<br />
year<br />
00-99<br />
80 MSB 0 0 0 0 0 0 0 0 N/A 00<br />
22