PC Control / Profi Control 645-12M Instruction Manual pdf - Kuhnke

More documents

Recommendations

Info

4.9.2.9. Overall program example This example program requests all services. The parameter field always starts with the same byte which means that is not possible to request several services at once: ======== KUBES ======================================================= Project Structure Project : 645 Network : DPCONTR created : Nov 24 1997 14:59 User : changed : Jan 22 1998 16:08 Comment : ====================================================================== ORG.ORG/1 | *———>CONTROL.PRO/1 | *———>DE_ACT.PRO/3 | *———>UN_FREEZ.PRO/4 | *———>UN_SYNC.PRO/5 | *———>SEE_DIAG.PRO/8 | *———>ERROR.PRO/2 | *———>CH_PARAM.PRO/6 | | | *———>BIPOLAR.INI/1 | | | *———>UNIPOLAR.INI/2 | *———>GET_DIAG.PRO/7 | *———>DP_CTRL.KNK/24 External modules: ======== KUBES ======================================================= Organisation Module IL Project : 645 Network : DPCONTR Module : ORG No.: 1 created : Nov 24 1997 15:00 User : changed : Jan 22 1998 16:21 ====================================================================== 1: ; Control and monitoring services 2: JPP CONTROL 1 3: 4 - 58
PC Control 645-12M on PROFIBUS ======== KUBES ======================================================= Program Module IL Project : 645 Network : DPCONTR Module : CONTROL No.: 1 created : Dec 08 1997 15:38 User : changed : Jan 22 1998 16:20 Comment: CONTROL ====================================================================== 1: ; __________________________________________________________________________ 2: ; Condition for new task: no task active 3: ; __________________________________________________________________________ 4: 5: L BASIS SBM02.00 ; (basic DP_CTRL address) 6: LSL 7: JPC END_CTRL ; task active if bit6 = 1 8: 9: ; Error analysis if not active 10: ; Analyse and clear any errors (bit7 of BASIS = 1 cond. error) 11: 12: ACTIVE L BASIS SBM02.00 ; (basic DP_CTRL address) 13: JPCN SERVICE7 14: = TASK SBM15.00 ; (active task flags+number) 15: 16: JPP ERROR 2 17: JP END_CTRL 18: ; __________________________________________________________________________ 19: 20: ; Activate/deactivate slave 21: SERVICE7 L ACTIVE SM00.00 ; (activate slave) 22: O DEACTIVE SM00.01 ; (deactivate slave) 23: JPCN SERVICE5 24: JPP DE_ACT 3 25: JP END_CTRL 26: 27: 28: ; FREEZE/UNFREEZE inputs 29: SERVICE5 L FREEZE SM00.02 ; (freeze inputs) 30: O UNFREEZE SM00.03 ; (unfreeze inputs) 31: JPCN SERVICE6 32: JPP UN_FREEZ 4 33: JP END_CTRL 34: 35: ; SYNC/UNSYNC outputs 36: SERVICE6 L SYNC SM00.04 ; (slave to freeze output data) 37: O UNSYNC SM00.05 ; (slave to update outputs) 38: JPCN SERVICE8 39: JPP UN_SYNC 5 40: JP END_CTRL 41: 42: ; Change USER parameters 43: SERVICE8 L USERPARA SM00.06 ; (change user parameters) 44: JPCN SERVICE9 45: JPP CH_PARAM 6 4 - 59
Page 1 and 2:
Kuhnke Electronics Instruction Manu
Page 3 and 4:
Table of contents Table of contents
Page 5 and 6:
Table of contents 4.5.2. External o
Page 7 and 8:
Table of contents B. PROFIBUS hardw
Page 9 and 10:
1. Purpose of PC Control 645-12M In
Page 11 and 12:
Introduction Advantages of decentra
Page 13 and 14:
Introduction VEBES VEBES, the netwo
Page 15 and 16:
2. Reliability and safety Reliabili
Page 17 and 18:
Reliability / safety 2.4. Safety Ou
Page 19 and 20:
Reliability / safety 2.5. Electroma
Page 21 and 22:
2.5.5. Protection against external
Page 23 and 24:
3. Hardware Hardware 3.1. Design 17
Page 25 and 26:
Hardware 3.2.2.1. Uninterrupted swi
Page 27 and 28:
Hardware 3.4.2. Setting the reset t
Page 29 and 30:
Hardware 3.5. Interfaces 3.5.1. V.2
Page 31 and 32:
Hardware 3.6. Memory PC Control 645
Page 33 and 34:
Hardware 3.8.2. How to avoid addres
Page 35 and 36:
Hardware -- Activate the "Memory" o
Page 37 and 38:
Hardware To reserve a memory range
Page 39 and 40:
i n 0 2 4LV o g 0 2 4LV o Sa t da t
Page 41 and 42:
PC Control 645-12M used as PLC 4.1.
Page 43 and 44:
PC Control 645-12M used as PLC -- S
Page 45 and 46: PC Control 645-12M used as PLC The
Page 47 and 48: 4.2. Going online with KUBES PC Con
Page 49 and 50: PC Control 645-12M used as PLC 4.2.
Page 51 and 52: 4.3. Memory settings PC Control 645
Page 53 and 54: 4.4. PLC working method PC Control
Page 55 and 56: 4.5.1.1. Short description of local
Page 57 and 58: 4.5.2. External operands as process
Page 61 and 62: 4.5.3.1. Status of PROFIBUS master
Page 63 and 64: 4.5.3.2. PEaxx.yy: DP slave status
Page 65 and 66: 4.6. Summary of commands PC Control
Page 73 and 74: 4.6.4. Shift and rotation commands
Page 79 and 80: 4.7. Types of operands PC Control 6
Page 83 and 84: PC Control 645-12M on PROFIBUS 4.9.
Page 85 and 86: PC Control 645-12M on PROFIBUS PROF
Page 87 and 88: PC Control 645-12M on PROFIBUS 4.9.
Page 89 and 90: 4.9.2.3.1. Choosing a station and g
Page 91 and 92: 4.9.2.4. Service 7: activate/deacti
Page 93 and 94: 4.9.2.6. Service 6: synchronise DP
Page 95: PC Control 645-12M on PROFIBUS 4.9.
Page 99 and 100: PC Control 645-12M on PROFIBUS ====
Page 107 and 108: PC Control 645-12M used as PLC 4.10
Page 109 and 110: 4.10.2. Undervoltage (supply, failu
Page 111 and 112: PC Control 645-12M used as PLC 4.10
Page 113 and 114: 4.10.5. Hierarchy error (failure #9
Page 115 and 116: A. Specifications Specifications A.
Page 117 and 118: Specifications A.2. Order specifica
Page 119 and 120: PROFIBUS hardware installation B. P
Page 121 and 122: PROFIBUS hardware installation B.1.
Page 127 and 128: PROFIBUS hardware installation Acti
Page 129 and 130: Index A accumulator 3-9 functional
Page 131 and 132: Index memory range 3-4 in DOS and W
show all

PC Control / Profi Control 645-12M Instruction Manual pdf - Kuhnke

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?