PC Control / Profi Control 645-12M Instruction Manual pdf - Kuhnke

More documents

Recommendations

Info

Operands 4.5.3.3. PSaxx.yy: Status of connections Status Description Operand range PSa00.00 to PEa07.13 contains the status messages for the DP slave connections, referenced by the station addresses. PSaxx.yy = slave station address xx*16 + yy: Operand DP slave address PSa00.00 0 PSa00.01 1 PSa00.02 2 etc. 0 Connection ok. 1 Connection not established. 2 Connection aborted. 3 Passive station. 4 No connection defined. 4 - 26
4.6. Summary of commands PC Control 645-12M used as PLC The following summary contains information about all available commands including the possible types of addressing, memory capacity and processing time required. Programming of external operands The execution times contained in the following tables are valid if a connection between the relevant PC Control 645 and the external participant has been established. When the network or a participant are switched on it may take a few seconds until the interconnections have been initialised. During this time, the signal states of external inputs are not current values. The same applies to the addressing of external outputs. 4.6.1. Logical operations commands Logic commands are the commands for logical operations between operands. This includes assignments of results. They can be executed with bit, byte and word operands. For further information on programming, use of the commands and programming examples please refer to our Programming Manual, E 417 GB. 4 - 27
Page 1 and 2:
Kuhnke Electronics Instruction Manu
Page 3 and 4:
Table of contents Table of contents
Page 5 and 6:
Table of contents 4.5.2. External o
Page 7 and 8:
Table of contents B. PROFIBUS hardw
Page 9 and 10:
1. Purpose of PC Control 645-12M In
Page 11 and 12:
Introduction Advantages of decentra
Page 13 and 14: Introduction VEBES VEBES, the netwo
Page 15 and 16: 2. Reliability and safety Reliabili
Page 17 and 18: Reliability / safety 2.4. Safety Ou
Page 19 and 20: Reliability / safety 2.5. Electroma
Page 21 and 22: 2.5.5. Protection against external
Page 23 and 24: 3. Hardware Hardware 3.1. Design 17
Page 25 and 26: Hardware 3.2.2.1. Uninterrupted swi
Page 27 and 28: Hardware 3.4.2. Setting the reset t
Page 29 and 30: Hardware 3.5. Interfaces 3.5.1. V.2
Page 31 and 32: Hardware 3.6. Memory PC Control 645
Page 33 and 34: Hardware 3.8.2. How to avoid addres
Page 35 and 36: Hardware -- Activate the "Memory" o
Page 37 and 38: Hardware To reserve a memory range
Page 39 and 40: i n 0 2 4LV o g 0 2 4LV o Sa t da t
Page 41 and 42: PC Control 645-12M used as PLC 4.1.
Page 43 and 44: PC Control 645-12M used as PLC -- S
Page 45 and 46: PC Control 645-12M used as PLC The
Page 47 and 48: 4.2. Going online with KUBES PC Con
Page 51 and 52: 4.3. Memory settings PC Control 645
Page 53 and 54: 4.4. PLC working method PC Control
Page 55 and 56: 4.5.1.1. Short description of local
Page 57 and 58: 4.5.2. External operands as process
Page 61 and 62: 4.5.3.1. Status of PROFIBUS master
Page 63: 4.5.3.2. PEaxx.yy: DP slave status
Page 73 and 74: 4.6.4. Shift and rotation commands
Page 79 and 80: 4.7. Types of operands PC Control 6
Page 83 and 84: PC Control 645-12M on PROFIBUS 4.9.
Page 85 and 86: PC Control 645-12M on PROFIBUS PROF
Page 89 and 90: 4.9.2.3.1. Choosing a station and g
Page 91 and 92: 4.9.2.4. Service 7: activate/deacti
Page 93 and 94: 4.9.2.6. Service 6: synchronise DP
Page 97 and 98: PC Control 645-12M on PROFIBUS ====
Page 107 and 108: PC Control 645-12M used as PLC 4.10
Page 109 and 110: 4.10.2. Undervoltage (supply, failu
Page 111 and 112: PC Control 645-12M used as PLC 4.10
Page 113 and 114: 4.10.5. Hierarchy error (failure #9
Page 115 and 116:
A. Specifications Specifications A.
Page 117 and 118:
Specifications A.2. Order specifica
Page 119 and 120:
PROFIBUS hardware installation B. P
Page 121 and 122:
PROFIBUS hardware installation B.1.
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
PROFIBUS hardware installation Acti
Page 129 and 130:
Index A accumulator 3-9 functional
Page 131 and 132:
Index memory range 3-4 in DOS and W
show all

PC Control / Profi Control 645-12M Instruction Manual pdf - Kuhnke

Create successful ePaper yourself

Delete template?

Save as template?