PC Control / Profi Control 645-12M Instruction Manual pdf - Kuhnke

More documents

Recommendations

Info

Interfaces/memory 3.5.2. PROFIBUS interface The PROFIBUS interface is located on the lower of the two D-Sub connectors. It is a female 9-pin connector with the following wiring: pin function 1 and casing shield 3 RxD/TxD-P 5 Data-Gnd 6 VP (+5 V) 8 RxD/TxD-N Please refer to chapter "B. PROFIBUS hardware installation" to learn how to install PROFIBUS. 3 - 8
Hardware 3.6. Memory PC Control 645-12M has large memory ranges: -- Flash EPROM, 512 kbyte *) For: program and permanent data -- RAM, 256 kbyte *) For: variable data, operand ranges -- Dual-Port-RAM, 16 kbyte For: data communication with the PC via the ISA interface -- PROFIBUS process image For: status image of decentralised I/Os *) Some of the memory is reserved for the monitor program. Please refer to chapter "4.3. Memory settings" to learn how much user memory is available 3.7. NiCd accumulator PC Control 645-12M has a NiCd accumulator for buffering defined RAM areas. In the PLC these are the remanent markers, i.e. bit and byte ranges that are not reset in Reset events (see above). Max. buffer time is about 36 days at an ambient temperature of 0...40 °C. Due to different lengths of time spent in the warehouse the charging state of the accumulator is undefined at the time of delivery. Please supply the device with voltage for at least 72 hours to charge the accumulator. In chapter "4.5.1.2. Accumulator function test" you will find a program suggestion for testing the accumulator functions. 3 - 9
Page 1 and 2: Kuhnke Electronics Instruction Manu
Page 3 and 4: Table of contents Table of contents
Page 5 and 6: Table of contents 4.5.2. External o
Page 7 and 8: Table of contents B. PROFIBUS hardw
Page 9 and 10: 1. Purpose of PC Control 645-12M In
Page 11 and 12: Introduction Advantages of decentra
Page 13 and 14: Introduction VEBES VEBES, the netwo
Page 15 and 16: 2. Reliability and safety Reliabili
Page 17 and 18: Reliability / safety 2.4. Safety Ou
Page 19 and 20: Reliability / safety 2.5. Electroma
Page 21 and 22: 2.5.5. Protection against external
Page 23 and 24: 3. Hardware Hardware 3.1. Design 17
Page 25 and 26: Hardware 3.2.2.1. Uninterrupted swi
Page 27 and 28: Hardware 3.4.2. Setting the reset t
Page 29: Hardware 3.5. Interfaces 3.5.1. V.2
Page 33 and 34: Hardware 3.8.2. How to avoid addres
Page 35 and 36: Hardware -- Activate the "Memory" o
Page 37 and 38: Hardware To reserve a memory range
Page 39 and 40: i n 0 2 4LV o g 0 2 4LV o Sa t da t
Page 41 and 42: PC Control 645-12M used as PLC 4.1.
Page 43 and 44: PC Control 645-12M used as PLC -- S
Page 45 and 46: PC Control 645-12M used as PLC The
Page 47 and 48: 4.2. Going online with KUBES PC Con
Page 51 and 52: 4.3. Memory settings PC Control 645
Page 53 and 54: 4.4. PLC working method PC Control
Page 55 and 56: 4.5.1.1. Short description of local
Page 57 and 58: 4.5.2. External operands as process
Page 61 and 62: 4.5.3.1. Status of PROFIBUS master
Page 63 and 64: 4.5.3.2. PEaxx.yy: DP slave status
Page 65 and 66: 4.6. Summary of commands PC Control
Page 73 and 74: 4.6.4. Shift and rotation commands
Page 79 and 80: 4.7. Types of operands PC Control 6
Page 81 and 82:
PC Control 645-12M used as PLC 4.8.
Page 83 and 84:
PC Control 645-12M on PROFIBUS 4.9.
Page 85 and 86:
PC Control 645-12M on PROFIBUS PROF
Page 87 and 88:
Page 89 and 90:
4.9.2.3.1. Choosing a station and g
Page 91 and 92:
4.9.2.4. Service 7: activate/deacti
Page 93 and 94:
4.9.2.6. Service 6: synchronise DP
Page 95 and 96:
Page 97 and 98:
PC Control 645-12M on PROFIBUS ====
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
PC Control 645-12M used as PLC 4.10
Page 109 and 110:
4.10.2. Undervoltage (supply, failu
Page 111 and 112:
PC Control 645-12M used as PLC 4.10
Page 113 and 114:
4.10.5. Hierarchy error (failure #9
Page 115 and 116:
A. Specifications Specifications A.
Page 117 and 118:
Specifications A.2. Order specifica
Page 119 and 120:
PROFIBUS hardware installation B. P
Page 121 and 122:
PROFIBUS hardware installation B.1.
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
PROFIBUS hardware installation Acti
Page 129 and 130:
Index A accumulator 3-9 functional
Page 131 and 132:
Index memory range 3-4 in DOS and W
show all

PC Control / Profi Control 645-12M Instruction Manual pdf - Kuhnke

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?