PC Control / Profi Control 645-12M Instruction Manual pdf - Kuhnke

More documents

Recommendations

Info

Purpose of PC Control 645-12M 1.2. Summary of PROFIBUS-DP features PROFIBUS is a field bus. Its name is an acronym of the term "Process Field Bus". DP stands for "Decentralised Periphery". It was developed to network controllers (such as PC Control 645-12M, Profi Control 680I, Modu Control 657P etc.) while providing an interface to the field level, i.e. to sensors and actuators (e.g. via decentralised input/output devices such as Profi I/O 690E or 680S). Open communication The principle of open communication is meant to guarantee interconnections between devices of different manufacturers. The standard for this field bus is set in Euronorm "EN 50 170, Volume 2, PROFIBUS". Topology PROFIBUS is normally constructed as a line, but a tree structure is also possible. The number of stations on any one line is limited to 32. Where that is not enough, a second line can be opened which is connected to the first line by a bidirectional line amplifier (repeater). Repeaters also count as stations so that the number of "real" stations on one line is reduced to 31 (or 30 with 2 repeaters). The number of bus stations can thus be increased to up to 122 by applying up to 3 repeaters. Station address Each PROFIBUS station is assigned its own station address under which it can be addressed by the other stations. Valid addresses are in the range of 0 to a maximum of 126. PC Control 645-12M has assigned its station address by VEBES, the network configurator. 1 - 4
Introduction VEBES VEBES, the network operating software, is the PROFIBUS configurator for Kuhnke PROFIBUS masters. The program is used for defining bus parameters, creating station lists and setting up the communication links between individual stations. Bus protocol PROFIBUS provides various protocols (profiles) to be able to react to different requirements. PC Control 645-12M supports the PROFIBUS-DP (class 1 master) protocol. Baudrate and other bus parameters PC Control 645-12M supports the following baudrates for communication via POFIBUS-DP: 9.6 kbit/s, 19.2 kbit/s, 93.75 kbit/s, 187.5 kbit/s, 500 kbit/s, 150 kbit/s, 3000 kbit/s, 6000 kbit/s, 12000 kbit/ s Most of the bus parameters for the network, including the baudrate, are set via VEBES and transmitted to PC Control 645-12M together with the KUBES project. Changing any hardware settings on the card itself is not required. For a comprehensive description please refer to instruction manual PROFIBUS, E 365 GB. 1 - 5
Page 1 and 2: Kuhnke Electronics Instruction Manu
Page 3 and 4: Table of contents Table of contents
Page 5 and 6: Table of contents 4.5.2. External o
Page 7 and 8: Table of contents B. PROFIBUS hardw
Page 9 and 10: 1. Purpose of PC Control 645-12M In
Page 11: Introduction Advantages of decentra
Page 15 and 16: 2. Reliability and safety Reliabili
Page 17 and 18: Reliability / safety 2.4. Safety Ou
Page 19 and 20: Reliability / safety 2.5. Electroma
Page 21 and 22: 2.5.5. Protection against external
Page 23 and 24: 3. Hardware Hardware 3.1. Design 17
Page 25 and 26: Hardware 3.2.2.1. Uninterrupted swi
Page 27 and 28: Hardware 3.4.2. Setting the reset t
Page 29 and 30: Hardware 3.5. Interfaces 3.5.1. V.2
Page 31 and 32: Hardware 3.6. Memory PC Control 645
Page 33 and 34: Hardware 3.8.2. How to avoid addres
Page 35 and 36: Hardware -- Activate the "Memory" o
Page 37 and 38: Hardware To reserve a memory range
Page 39 and 40: i n 0 2 4LV o g 0 2 4LV o Sa t da t
Page 41 and 42: PC Control 645-12M used as PLC 4.1.
Page 43 and 44: PC Control 645-12M used as PLC -- S
Page 45 and 46: PC Control 645-12M used as PLC The
Page 47 and 48: 4.2. Going online with KUBES PC Con
Page 51 and 52: 4.3. Memory settings PC Control 645
Page 53 and 54: 4.4. PLC working method PC Control
Page 55 and 56: 4.5.1.1. Short description of local
Page 57 and 58: 4.5.2. External operands as process
Page 61 and 62: 4.5.3.1. Status of PROFIBUS master
Page 63 and 64:
4.5.3.2. PEaxx.yy: DP slave status
Page 65 and 66:
4.6. Summary of commands PC Control
Page 67 and 68:
PC Control 645-12M used as PLC 4.6.
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
4.6.4. Shift and rotation commands
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
4.7. Types of operands PC Control 6
Page 81 and 82:
Page 83 and 84:
PC Control 645-12M on PROFIBUS 4.9.
Page 85 and 86:
PC Control 645-12M on PROFIBUS PROF
Page 87 and 88:
Page 89 and 90:
4.9.2.3.1. Choosing a station and g
Page 91 and 92:
4.9.2.4. Service 7: activate/deacti
Page 93 and 94:
4.9.2.6. Service 6: synchronise DP
Page 95 and 96:
Page 97 and 98:
PC Control 645-12M on PROFIBUS ====
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
PC Control 645-12M used as PLC 4.10
Page 109 and 110:
4.10.2. Undervoltage (supply, failu
Page 111 and 112:
PC Control 645-12M used as PLC 4.10
Page 113 and 114:
4.10.5. Hierarchy error (failure #9
Page 115 and 116:
A. Specifications Specifications A.
Page 117 and 118:
Specifications A.2. Order specifica
Page 119 and 120:
PROFIBUS hardware installation B. P
Page 121 and 122:
PROFIBUS hardware installation B.1.
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
PROFIBUS hardware installation Acti
Page 129 and 130:
Index A accumulator 3-9 functional
Page 131 and 132:
Index memory range 3-4 in DOS and W
show all

PC Control / Profi Control 645-12M Instruction Manual pdf - Kuhnke

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?