PC Control / Profi Control 645-12M Instruction Manual pdf - Kuhnke

More documents

Recommendations

Info

PROFIBUS hardware installation Order specifications Name Part number Passive bus terminator for cable type A ----- with horizontal cable OUT connector 690.180.07 ----- with vertical cable OUT connector 690.180.08 The bus terminator is to be supplied with power at all times. This cannot be guaranteed in the case of the above (passive) terminator because this type is supplied via the controller. When you switch the controller off, you also deactivate the bus terminator. There is no passive bus terminator available for cable type B. B - 8
PROFIBUS hardware installation Active bus termination For the above reason, use an active bus termination in networks that allow one terminal station to be switched off during bus operation. Active bus terminators are equipped with their own power supply so that their function is guaranteed at any time. Top view: Side view: L+ 0 PE 24 V DC On Termination RPOFIBUS Line A 680.180.14 70 115 ~121 45 Circuit diagram: PROFIBUS Line A Schirm (Shield) RxD/TxD-P RxD/TxD-N 1 3 8 Rt 220 Ω Ru 390 Ω +5 V Rd 390 Ω 0V PE L+ 24 V DC 0 Power supply D-Sub, 9p. Ill: Active bus terminator, 24 V DC power supply Active bus terminators have a snap-on device for installation on carrier rails. Install directly next to the terminal station. Connect a bus node to the terminal station that has a short line to the bus terminator. Order specifications Name Part number Active bus terminator, 230 V AC power supply -- for cable type A 680.180.12 -- for cable type B 680.180.10 Active bus terminator, 24 V DC power supply -- for cable type A 680.180.14 -- for cable type B 680.180.15 B - 9
Page 1 and 2:
Kuhnke Electronics Instruction Manu
Page 3 and 4:
Table of contents Table of contents
Page 5 and 6:
Table of contents 4.5.2. External o
Page 7 and 8:
Table of contents B. PROFIBUS hardw
Page 9 and 10:
1. Purpose of PC Control 645-12M In
Page 11 and 12:
Introduction Advantages of decentra
Page 13 and 14:
Introduction VEBES VEBES, the netwo
Page 15 and 16:
2. Reliability and safety Reliabili
Page 17 and 18:
Reliability / safety 2.4. Safety Ou
Page 19 and 20:
Reliability / safety 2.5. Electroma
Page 21 and 22:
2.5.5. Protection against external
Page 23 and 24:
3. Hardware Hardware 3.1. Design 17
Page 25 and 26:
Hardware 3.2.2.1. Uninterrupted swi
Page 27 and 28:
Hardware 3.4.2. Setting the reset t
Page 29 and 30:
Hardware 3.5. Interfaces 3.5.1. V.2
Page 31 and 32:
Hardware 3.6. Memory PC Control 645
Page 33 and 34:
Hardware 3.8.2. How to avoid addres
Page 35 and 36:
Hardware -- Activate the "Memory" o
Page 37 and 38:
Hardware To reserve a memory range
Page 39 and 40:
i n 0 2 4LV o g 0 2 4LV o Sa t da t
Page 41 and 42:
PC Control 645-12M used as PLC 4.1.
Page 43 and 44:
PC Control 645-12M used as PLC -- S
Page 45 and 46:
PC Control 645-12M used as PLC The
Page 47 and 48:
4.2. Going online with KUBES PC Con
Page 49 and 50:
Page 51 and 52:
4.3. Memory settings PC Control 645
Page 53 and 54:
4.4. PLC working method PC Control
Page 55 and 56:
4.5.1.1. Short description of local
Page 57 and 58:
4.5.2. External operands as process
Page 59 and 60:
Page 61 and 62:
4.5.3.1. Status of PROFIBUS master
Page 63 and 64:
4.5.3.2. PEaxx.yy: DP slave status
Page 65 and 66:
4.6. Summary of commands PC Control
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
4.6.4. Shift and rotation commands
Page 75 and 76: PC Control 645-12M used as PLC 4.6.
Page 79 and 80: 4.7. Types of operands PC Control 6
Page 83 and 84: PC Control 645-12M on PROFIBUS 4.9.
Page 85 and 86: PC Control 645-12M on PROFIBUS PROF
Page 89 and 90: 4.9.2.3.1. Choosing a station and g
Page 91 and 92: 4.9.2.4. Service 7: activate/deacti
Page 93 and 94: 4.9.2.6. Service 6: synchronise DP
Page 97 and 98: PC Control 645-12M on PROFIBUS ====
Page 107 and 108: PC Control 645-12M used as PLC 4.10
Page 109 and 110: 4.10.2. Undervoltage (supply, failu
Page 111 and 112: PC Control 645-12M used as PLC 4.10
Page 113 and 114: 4.10.5. Hierarchy error (failure #9
Page 115 and 116: A. Specifications Specifications A.
Page 117 and 118: Specifications A.2. Order specifica
Page 119 and 120: PROFIBUS hardware installation B. P
Page 121 and 122: PROFIBUS hardware installation B.1.
Page 123 and 124: PROFIBUS hardware installation B.2.
Page 125: PROFIBUS hardware installation B.2.
Page 129 and 130: Index A accumulator 3-9 functional
Page 131 and 132: Index memory range 3-4 in DOS and W
show all

PC Control / Profi Control 645-12M Instruction Manual pdf - Kuhnke

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?