SUPER DIGITAL
SUPER DIGITAL SUPER DIGITAL
Check code Outdoor LED display Check and troubleshooting (Item without special mention Indicates part of outdoor unit.) [P19] ¡ ¥ ¡ ¥ ¡ l l l ¡ ¥ ¡ ¡ [4-way valve inverse error] Is operation of 4-way valve normal? (Check pipe temp., etc. in cooling/heating operation.) NO YES Temperature sensor check TE sensor CN601 TS sensor CN600 Indoor TC sensor Defect → Correct and repair Is the coil resistance value of 4-way valve between 1.3 and 1.6kΩ? NO Replace coil of 4-way valve. YES Check operation of outdoor P.C. board. (See below.) Error Check outdoor P.C. board. Defect → replace OK Check 4-way valve. Defect → Replace Check method of outdoor P.C. board operation (Self-hold valve type) 1) Set SW804 of Dip switch as the following figure and then push SW801 for approx. 1 second to check exchange operation to cooling cycle/heating cycle. • Power is turned on for approx. 10 seconds. • When checking again, check operation 1 minute or more after the first check because exothermic of part (Coil, resistance R700) is large. (There is no problem when coil is not connected.) 2) After check, turn off all the Dip switch SW804. Exchange to cooling cycle Exchange to heating cycle SW804 SW801 CN701 ON 1 2 3 4 1 Push 4 SW804 SW801 CN701 ON 1 2 3 4 1 Push 4 DC200V or more DC200V or more Note) Check by tester Analog tester : Good if over DC200V Digital tester : Good if Max. value is over DC200V though the varied value may be displayed. – 116 –
Check code Outdoor LED display Check and troubleshooting (Item without special mention Indicates part of outdoor unit.) [P20] ¡ l ¡ l ¡ ¥ l l ¡ ¥ ¡ ¡ [High pressure protective operation] Is valve fully opened? YES Reset the power supply and then perform test run matching to the season. NO Cooling season Cooling operation Open valve fully. Heating season Heating operation Is there no problem on outdoor TL sensor? (Measurement of resistance value) YES NO Replace sensor. Is there no crack or loosening of outdoor fan? NO YES Check outdoor fan. Defect → Replace, retightening Does not the outdoor fan perform abnormal operation? NO YES Check the same items as [P22] error. Is there no element which interfere heat exchange of outdoor unit? • Clogging of heat exchanger • Short circuit YES NO Eliminate interfering element. Check overcharge of refrigerant, clogging of cycle, broken pipe, abnormal overload, etc. Defect → Correct defective position. Does indoor fan normally operate? NO Are indoor fan motor and connector normal? NO YES YES Repair defective position. Are resistance values of indoor TC and TCJ sensors normal? NO Replace sensor. Is there no element which interfere heat exchange of indoor unit? • Clogging of filter • Clogging of heat exchanger • Short circuit NO YES YES Check indoor P.C. board. Defect → Replace Eliminate interfering element. Check overcharge of refrigerant, clogging of cycle, broken pipe, abnormal overload, etc. Defect → Correct defective position. – 117 –
- Page 65 and 66: No. Item Outline of specifications
- Page 67 and 68: No. Item Outline of specifications
- Page 69 and 70: No. Item Outline of specifications
- Page 71 and 72: No. Item Outline of specifications
- Page 73 and 74: No. Item Outline of specifications
- Page 75 and 76: Optional power supply CN309 (Yellow
- Page 77 and 78: - 77 - L-phase power supply lead (B
- Page 79 and 80: 3. Outdoor fan control SP110 SP140
- Page 81 and 82: 7. Current release value shift cont
- Page 83 and 84: 1. Pulse Motor Valve (PMV) control
- Page 85 and 86: 2) Heating fan control The outdoor
- Page 87 and 88: 10-1. Summary of Troubleshooting 1
- Page 89 and 90: 10-2. Troubleshooting 10-2-1. Outli
- Page 91 and 92: 10-2-2. Others (Other than Check Co
- Page 93 and 94: - 93 - Check Code List (Outdoor) Re
- Page 95 and 96: Error mode detected by indoor unit
- Page 97 and 98: Error mode detected by outdoor unit
- Page 99 and 100: 10-2-4. Diagnostic Procedure for Ea
- Page 101 and 102: Revised 2: Jun., 2008 [E18 error] I
- Page 103 and 104: [P10 error] Is connection of float
- Page 105 and 106: [F02 error] Revised 2: Jun., 2008
- Page 107 and 108: [E03 error] (Master indoor unit) [
- Page 109 and 110: Check code Outdoor LED display Che
- Page 111 and 112: Check code Outdoor LED display Che
- Page 113 and 114: Check code [L29] Outdoor LED displa
- Page 115: Check code Outdoor LED display Che
- Page 119 and 120: Temperature sensor Temperature - Re
- Page 121 and 122: Lamp indication Check code Cause of
- Page 123 and 124: - 123 - Check Code List (Outdoor) R
- Page 125 and 126: Error mode detected by remote contr
- Page 127 and 128: 10-2-9. Diagnostic Procedure for Ea
- Page 129 and 130: [E18 error] Is inter-unit cable of
- Page 131 and 132: [P10 error] Revised 2: Jun., 2008
- Page 133 and 134: [F02 error] Revised 2: Jun., 2008
- Page 135 and 136: [E03 error] (Master indoor unit) [
- Page 137 and 138: Check code [F12] [Suction temp. sen
- Page 139 and 140: Check code [P22] [Fan system error]
- Page 141 and 142: 11. REPLACEMENT OF SERVICE P.C. BOA
- Page 143 and 144: Revised 2: Jun., 2008 Setting 4-way
- Page 145 and 146: Revised 2: Jun., 2008 Table 1. Sett
- Page 147 and 148: 12-1. Indoor Unit 12. SETUP AT LOCA
- Page 149 and 150: Procedure 1 2 Turn on power of the
- Page 151 and 152: 12-1-4. Function Selection Setup P
- Page 153 and 154: DN Item Contents At shipment from f
- Page 155 and 156: 12-1-6. Monitor Function of Remote
- Page 157 and 158: n Indoor unit power-ON sequence Pow
- Page 159 and 160: 4. Wiring specifications • Use 2-
- Page 161 and 162: 2. How to confirm the central contr
- Page 163 and 164: 4. How to set louver lock (Louver f
- Page 165 and 166: Be sure to make ceiling setting whe
Check<br />
code<br />
Outdoor<br />
LED display<br />
<br />
Check and troubleshooting<br />
(Item without special mention Indicates part of outdoor unit.)<br />
[P19]<br />
<br />
¡ ¥<br />
¡ ¥<br />
¡ l<br />
l l<br />
¡ ¥<br />
¡ ¡<br />
[4-way valve inverse error]<br />
Is operation of<br />
4-way valve normal?<br />
(Check pipe temp., etc. in<br />
cooling/heating operation.)<br />
NO<br />
YES<br />
Temperature sensor check<br />
TE sensor CN601<br />
TS sensor CN600<br />
Indoor TC sensor<br />
Defect → Correct and repair<br />
Is the coil<br />
resistance value of 4-way valve<br />
between 1.3 and 1.6kΩ?<br />
NO<br />
Replace coil of 4-way valve.<br />
YES<br />
Check operation of<br />
outdoor P.C. board.<br />
(See below.)<br />
Error<br />
Check outdoor P.C. board.<br />
Defect → replace<br />
OK<br />
Check 4-way valve.<br />
Defect → Replace<br />
Check method of outdoor P.C. board operation (Self-hold valve type)<br />
1) Set SW804 of Dip switch as the following figure and then push SW801 for<br />
approx. 1 second to check exchange operation to cooling cycle/heating cycle.<br />
• Power is turned on for approx. 10 seconds.<br />
• When checking again, check operation 1 minute or more after the first check<br />
because exothermic of part (Coil, resistance R700) is large.<br />
(There is no problem when coil is not connected.)<br />
2) After check, turn off all the Dip switch SW804.<br />
Exchange to cooling cycle<br />
Exchange to heating cycle<br />
SW804 SW801 CN701<br />
ON<br />
1 2 3 4<br />
1<br />
Push<br />
4<br />
SW804 SW801 CN701<br />
ON<br />
1 2 3 4<br />
1<br />
Push<br />
4<br />
DC200V or more<br />
DC200V or more<br />
Note) Check by tester<br />
Analog tester : Good if over DC200V<br />
Digital tester : Good if Max. value is over DC200V though the varied<br />
value may be displayed.<br />
– 116 –